用热分析法研究硝化棉的熔化过程

用ＭＤＳＣ，显微镜温台熔点测定仪和固体原位反应池／快速扫描傅立叶变换红外光谱联用装置考察了硝化棉的熔化过程。ＭＤＳＣ曲线表明吸热过程是可逆的，它系由ＮＣ和部分分解凝聚相产物的混合物的固液相变所引起。由ＮＣ的ＭＤＳＣ曲线得到的熔点，熔化含，熔化熵，分解含和分解反应热温熵分别为４７６．８４Ｋ，２０５．６Ｊ．ｇ＾－１，０．４３１２Ｊ．ｇ＾－１．Ｋ＾－１，－２４７５．０Ｊ．ｇ＾－１，－５．２４２Ｊ．ｇ＾－     

Advanced thin-film silicon-on-sapphire technology: microwavecircuit applications

This paper reviews the prospects of thin-film silicon-on-sapphire (TFSOS) CMOS technology in microwave applications in the 1-5 GHz regime and beyond and presents the first demonstration of microwave integrated circuits based on this technology, MOSFET's optimized for microwave use, with 0.5-μm optically defined gate lengths and a T-gate structure, have f_t values of 25 GHz (14 GHz) and f_max values of 66 GHz (41 GHz) for n-channel (p-channel) devices and have noise figure values below 1 db at 2 GHz, some of the best reported performance characteristics of any silicon-based MOSFET's to date. On-chip spiral inductors exhibit quality factors above ten. Circuit performance compares favorably with that of other CMOS-based technologies and approach performance levels similar to those obtained by silicon bipolar technologies. The results demonstrate the significant potential of this technology for microwave applications     

Stress-affected transformation to lower bainite

Experiments have been conducted on the formation of lower bainite under the influence of an externally applied stress. It was found that both the ferritic and cementite components of the microstructure respond to the stress. The ferrite plates that grow appear to comply best with the applied stress, leading to an aligned microstructure. Within any given ferrite plate, the stress was found to favour the formation of a single variant of cementite. The results are consistent with a displacive mechanism of transformation, and provide an explanation for the frequent observation that cementite precipitates in a single orientation within any given plate of lower bainite ferrite.     

A structured procedure for analysis and design of order pick systems

We present a structured procedure for order pick system (OPS) analysis and design that has been established on literature review and interviews with and presentations to OPS experts. In particular, we attempt to include the thinking processes that occur between OPS designers and owners. The design procedure and related issues are discussed in the order of input, selection, and evaluation stages.     

Feasibility of adding a personal communications network to anexisting fixed-service microwave system

This paper examines the feasibility of adding a personal communication network (PCN) to a frequency band which is already allocated to fixed-service microwave systems. To achieve this goal, spread spectrum techniques are used to spread narrowband PCN signals into wideband. The forward and reverse link performance of PCN users under the influence of the microwave system and the influence of PCN users on the microwave system are both examined. It is proven that spectrum sharing between the PCN network and microwave systems is indeed feasible. Although our analysis is done based upon the consideration of only one microwave system, it can be easily extended to allow the appearance of two or more microwave systems     

Performance of GaAs-AlGaAs V-grooved inner stripe quantum-well wirelasers with different current blocking configurations

GaAs-AlGaAs V-grooved inner stripe (VIS) quantum-well wire (QWW) lasers grown by metalorganic chemical vapor deposition with different current blocking configurations, n-blocking on p-substrate (VIPS), p-n-p-n blocking on n-substrate (VI(PN)_nS) and p-blocking on n-substrate (VINS) have been fabricated and characterized. The VIPS QWW lasers show the most stable characteristics with effective current confinement: one of the lasers shows fundamental transverse mode, lasing up to 5 mW/facet, typical threshold current of 39.9 mA at 818.5 mm, an external differential quantum efficiency of 24%/facet, and characteristic temperature of 92 K. The current tuning rate was almost linear at 0.031 mm/mA, and the temperature tuning rate was measured to be 0.14 nm/°C. Comparison of the light output versus current characteristics of the lasers with different current blocking configurations is presented here     

Multigrid computation for curve fitting in the wavelet domain

A multi-layer multigrid algorithm for curve fitting in the wavelet domain is presented. This algorithm is achieved by applying a wavelet transform to each grid of the conventional multigrid structure. Using a wavelet transform, the convergent rate in each grid is improved and the total system can converge more quickly     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.     

PDC钻头在胜利油田深井钻井中的应用

胜利油田为提高深井钻井速度，试验应用了PDC钻头，结果表明，深井钻井应用PDC钻头可大幅度提高机械钻速，缩短建井周期，降低钻井成本，经济效益明显。通过大量的现场试验，扩大了PDC钻头在胜利油田的使用范围，并取得很好的效果，初步形成了PDC钻头推广应用区域模式。详细介绍了胜利油田不适用PDC钻头钻进的地层岩性，给出了钻头选型及钻井参数选择原则，并对应用效果进行了分析。