防止设备结垢延长乙烯装置运行周期

设备结垢堵塞问题已成为乙烯装置长周期运转的难点。笔者重点论述了急冷油塔和冷箱的结垢问题及防范措施。     

Numerical Study of Solid-Liquid Two-Phase Flow in Stirred Tanks with Rushton Impeller (Ⅰ) Formulation and Simulation of Flow Field

Three-dimensional solid-liquid flow is mathematically formulated by means of the "two-fluid" approach and the two-phase k-ε-Ap turbulence model. The turbulent fluctuation correlations appearing in the Reynolds time averaged governing equations are fully incorporated. The solid-liquid flow field and solid concentration distribution in baffled stirred tanks with a standard Rushton impeller are numerically simulated using an improved "inner-outer" iterative procedure. The flow pattern is identified via the velocity vector plots and a recirculation loop with higher solid concentration is observed in the central vicinity beneath the impeller. Comparison of     

基于流动平衡的塑料挤出模优化设计

在构建流道三维参数化模型的基础上,将有限元数值分析和优化技术相结合,以口模出口处型材截面上各子区域平均流速相等为优化目标,以压缩段入口壁厚和平直段长度为设计变量,对挤出模优化设计进行了研究。并以实例说明了优化设计的具体过程,验证了所用方法的正确性和有效性。     

Possible Energy Network with polygeneration system and CCS for China

On basis of adopting polygeneration systems for power and alternative fuels,capturing CO2 with near zero energy penalties,and storing CO2 on sites,a new kind of Energy Network can integrate energy utilization,CO2 capture,transportation and storage synthetically.Techno-economic analysis of this solution focusing on Inner Mongolia and the Yangtze River Delta districts had been carried with comparison to the chain method for energy utilization and CO2 sequestration.This solution can save 21.5% of energy,and re...     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...     

A novel shaft-less double suction mini pump

A novel double suction shaft-less mini pump was developed for heat control of small energy systems in this study.The mini pump impeller with an exit diameter of 40 mm was combined with the motor rotor supported by the hybrid dynamic bearing.The specific speed of the pump was 125 min-1 m3 min-1 m.The hydraulic performance of the pump was investigated experimen-tally under four rotational speeds.From the test results,it was recognized that the pump could provide a flow discharge of 5 L/min and head of 1.5 m,w...     

Fuel combustion test in constant volume combustion chamber with built-in adaptor

Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hol...     

Dynamic equivalent method of interconnected power systems with consideration of motor loads

The existing equivalent methods usually only deal with static load models and neglect the dynamic characteristics of loads such as induction motors.This paper presents a dynamic equivalent method which considers motor dynamics.At first,the clustering criterion of motor loads is given.The motors with similar dynamic characteristics are classified into one group.Then,reduction of motors in the same group is carried out.Finally,parameters of the equivalent motor are calculated and the equivalent system is thus...     

供热网循环水泵效率的研究

城市供热系统是极其重要而复杂的大系统,为了提高系统的社会效益和经济效益,从大连北海热电集团热电联产供热管网的实际出发,运用了最小二乘法原理,对采暖循环水泵的性能数据进行曲线拟合,得出了水泵的真正运行状况,并且对使用单台水泵、双台并联或3台并联水泵3种不同情况下的水力工况水泵效率进行了比较和分析。结果表明,单纯地增加并列泵数量对增加流量并无显著变化,并且使并列泵的效率明显下降,只有认真进行严格地工况分析,找到最佳工况点,才能保证整个热系统正常运行。