High PVC film‐forming composite latex particles via miniemulsification,part 1: Preparation

Miniemulsification technology was used to encapsulate TiO₂ particles inside a styrene/n‐butyl acrylate copolymer with high loading levels (11 to 70% PVC (pigment volume concentration)). In this approach, a St/BA copolymer dissolved in toluene in the presence of a costabilizer (hexadecane) was mixed with a dispersion of TiO₂ particles in toluene and sonified, and then emulsified in an aqueous surfactant solution by sonification. The effect of sonification time on both the dispersibility of the TiO₂ particles in the presence of the copolymer and hexadecane and on the encapsulated particle size was investigated. Particle size analysis by dynamic light scattering showed that these composite latexes are quite stable. It was also found that as the TiO₂ loading increased from 11 to 43% PVC, the particle size of the TiO₂ dispersion decreased while the polymer‐encapsulated TiO₂ particle size increased. The effect of surfactant concentration (sodium lauryl sulfate, SLS) on the encapsulated particle size was investigated using four different SLS concentrations in the 11% PVC system. The results showed that as the SLS concentration increased the particle size decreased, as expected. Also it was found that the minimum surfactant concentration that gives stable encapsulated TiO₂ particles is above 10 mM SLS. The role of HD in the recipe was studied for an artificial latex containing no TiO₂ and one prepared at 11% PVC, in terms of particle size before and after solvent stripping, and its effect on the T_g. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4504–4516, 2006     

Dense Al2O3/ZrO2 Particulate Composites by Free Sintering of Coated Powders

Composite powders, prepared by coating coarse ZrO₂ particles with fine Al₂O₃ powder using a chemical precipitation technique, were compacted and sintered freely at a constant heating rate of 4°C/min to ∼1600°C. Composites containing up to ∼30 vol% inclusions were sintered to nearly full density under the same conditions used for the unreinforced matrix. Furthermore, the sintering kinetics were not influenced significantly by the inclusion volume fraction. The sinterability of the composites formed from the coated powders was significantly better than that for similar composites formed from mechanically mixed powders. The present data provide a further demonstration that the use of coated powders may have widespread applicability for the fabrication, by free sintering, of dense ceramic particulate composites.     

HColonies: a new hybrid metaheuristic for medical data classification

Medical data feature a number of characteristics that make their classification a complex task. Yet, the societal significance of the subject and the computational challenge it presents has caused the classification of medical datasets to be a popular research area. A new hybrid metaheuristic is presented for the classification task of medical datasets. The hybrid ant–bee colonies (HColonies) consists of two phases: an ant colony optimization (ACO) phase and an artificial bee colony (ABC) phase. The food sources of ABC are initialized into decision lists, constructed during the ACO phase using different subsets of the training data. The task of the ABC is to optimize the obtained decision lists. New variants of the ABC operators are proposed to suit the classification task. Results on a number of benchmark, real-world medical datasets show the usefulness of the proposed approach. Classification models obtained feature good predictive accuracy and relatively small model size.     

Rheological behaviour of polysaccharide aqueous solutions

Several data relative to the viscosity of water-soluble polysaccharide solutions were collected from the literature and processed by different rheological models. Some relationships between the viscosity of these polymer solutions, their molecular weight and their solution concentrations, were established and their validity checked. Thus, an accurate equation correlating the viscosity and both the shear rate and the solution concentration of different water soluble polysaccharides (xanthan, hyaluronan, carboxymethylcellulose) was deduced on the basis of Cross' model which suggests two domains in which the viscosity is constant, i.e. very low and very high shear rate ranges. Then, an expression relating the zero-shear viscosity (A) and the concentration of their solutions was proposed. Finally, an alternative equation to that of Mark–Houwink correlating the molecular weight and the intrinsic viscosity of the water-soluble polysaccharides studied in this paper was found.     

Role of sand on curing of partex surface by UV radiation

A partex surface was modified by a UV‐curing system with epoxy acrylate (EB‐600). A set of formulations was prepared with oligomer and the trifunctional monomer trimethylol propane triacrylate in different combinations of percentages (1–5%) of sand to study the role of sand in various physical properties of UV‐cured thin films, as well as partex surfaces. Increased pendulum hardness (PH), gloss, adhesion, and abrasion values were obtained by the addition of sand into the partex surfaces. The best results were obtained with the formulation containing 3% sand. An enhanced PH and a decreased percentage of gel content of the UV‐cured film was observed with an increase of the sand concentration. A simulated weathering test was performed with partex surfaces cured by a formulation containing 3% sand in the base coat. The losses of the physical properties were found to be lower over the surface treated with the formulation containing sand. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2385–2392, 2002     

Effect of alkali and ultraviolet (UV) radiation pretreatment on physical and mechanical properties of 1,6‐hexanediol diacrylate–grafted jute yarn by UV radiation

To improve the physicomechanical properties of jute yarn, grafting with 1,6‐hexanediol diacrylate (HDDA) monomer was performed by a UV radiation technique. A series of HDDA solutions of various concentrations in methanol were prepared. A small quantity of photoinitiator (Darocur‐1664) was also added to HDDA solutions. To optimize the conditions for grafting, the effects of monomer concentration, soaking time, and radiation doses were studied by varying the number of soaking times along with variation of monomer concentrations and UV radiation intensities. The extent of polymer loading and the mechanical properties like tensile strength (TS), elongation at break (Eb), and tensile modulus of both treated and untreated jute were investigated. The highest tensile strength, polymer loading, and modulus were achieved with 5% HDDA concentration, 5 min soaking time, and the 4th pass of UV radiation. This set of conditions was selected as optimum and produced enhanced tensile strength (67%), modulus (108%), and polymer loading (11%) over those of virgin fiber. To further improve the mechanical properties the jute yarns were pretreated with alkali (5% NaOH) solution and after that the alkali‐treated yarn were treated under UV radiation of various intensities. The pretreated samples were grafted with optimized monomer concentration (5% HDDA). Increased properties of alkali + UV‐pretreated and grafted samples such as polymer loading (12%), tensile strength (103%), elongation at break (46%), and modulus (114%) were achieved over those of virgin jute yarn. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 18–24, 2004     

Arylidene polymers. XVIII. Synthesis and thermal behavior of organometallic arylidene polyesters containing ferrocene derivatives in the main chain

A new interesting category of organometallic polyesters based on diarylidenecycloalkanones containing ferrocene derivatives in the polymer main chain has been prepared by interfacial polycondensation of 1,1′-dichlorocarbonyl ferrocene or 1,1′-dichlorocarbonyl-4,4′-diiodoferrocene with 2,5-bis(p-hydroxybenzylidene)cyclopentanone, 2,5-divanillylidenecyclopentanone, 2,6-bis(p-hydroxybenzylidene)cyclohexanone, 2,6-divanillylidenecyclohexanone, and 2,7-bis(p-hydroxybenzylidene) cycloheptanone. The resulting polyesters were characterized by elemental analyses, infrared spectroscopy, solubility, and viscometry measurements. The thermal behavior of the synthesized polymers was evaluated by thermal gravimetric analysis and correlated with their structures. The crystallinity of all polymers were examined by x-ray diffraction analysis. Moreover, the electrical conductivity of a selected example of polymer was investigated above the temperature range (300–500 K) and showed that it followed an Arrhenius-type equation with activation energy 2.09 eV. © 1993 John Wiley & Sons, Inc.     

Antimicrobial activity of statistical polymethacrylic sulfopropylbetaines against gram‐positive and gram‐negative bacteria

A series of statistical copolymers derived from 2‐(dimethylamino)ethyl methacrylate with four different hydrophobic comonomers (ethyl, butyl, cyclohexyl, and octyl methacrylates) have been prepared via conventional free radical copolymerization under bulk conditions. The copolymers have been subsequently modified, with 1,3‐propanesultone to yield the corresponding polysulfoproylbetaine derivatives. Those copolymers exhibiting the requisite aqueous solubility have been screened with respect to their antimicrobial activity against two common and notorious pathogens, namely Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli). We show that certain copolymers do indeed exhibit antimicrobial activity. The extent of activity is related to the molecular characteristics of the materials such as the molar composition and structure of the hydrophobic comonomer. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1036–1041, 2006     

Sintering of Ceramic Particulate Composites: Effect of Matrix Density

Composites consisting of a fine-grained, polycrystalline zinc oxide matrix and <10 vol% coarse, rigid silicon carbide inclusions were prepared by the same mixing procedure and then compacted to produce samples with matrix densities of 0.45 and 0.68 of the theoretical. The samples were sintered under identical temperature profiles in separate experiments that employed either a constant rate of heating of 4°C/min or near isothermal heating at 735°C. The ratio of the densification rate of the composite matrix to the densification rate of the unreinforced zinc oxide was found to be independent of the initial matrix density. This ratio increased significantly with temperature in the constant-heating-rate experiments but was relatively constant in the isothermal experiments. The results indicate that microstructural coarsening may be an important mechanism for explaining the reduced sinterability of polycrystalline matrix composites.