月亮湾燃机电厂5号机海水泵阀门轴承座连接端失效原因分析

采用宏观检查、化学分析、金相检验、能谱分析和断口扫描等方法,对月亮湾燃机电厂5号机海水泵阀门轴承座失效原因进行分析。分析结果显示,失效主要为缝隙腐蚀引起的沿晶脆性断裂,对此提出了使用不吸湿的垫片或填料、轴承座边缘部位喷耐蚀涂层(?)刷防腐涂料,以及改变设计结构,避免出现缝隙及停滞区等措施。     

建立雷诺方程的一种新概念

针对工程应用中所存在的多种具体物理形式和多种工况条件的流体膜润滑型式,归纳给出了3类典型摩擦副流体膜润滑所对应的3种微圆柱流量物理模型、几何楔和有效法向速度差特征式的概念,由可压缩流微圆柱流量连续方程导出了有关的常用支承流体膜润滑广义雷诺方程。这样使分析方法和物理意义简明;同时还修正了此前长期被一些广为流传的专著或论文所忽视的有关问题;并给出了一些对基本形式雷诺方程润滑理论的实验验证。     

喷雾反应器中甲烷水合物生长动力学模型

提出了喷雾反应器中甲烷水合物的形成机理,并引入传质对水合反应影响的有效因子等参数,得到了喷雾法生成水合物的改进动力学方程.通过实验验证,实验数据与模型计算数据基本吻合,平均误差为4.63%.方程回归得出甲烷水合物表观活化能(Ea)为54.25 kJ/mol,根据文献结果,说明喷雾反应器中甲烷水合物生长过程由表面反应所控制.     

劣化导热油的离心沉降处理探索

采用离心沉降方法处理受到粗对苯二甲酸（TA）污染和劣化的加氢精制系统导热油,对离心沉降时间、离心沉降转速等工艺条件对导热油的固体杂质和胶质含量、酸值的影响进行了讨论,确定了最佳的工艺条件,试验结果表明离心沉降的处理方法可以显著降低导热油中的固体杂质和胶质含量及酸值。     

浅谈电镀生产中的质量管理

阐述了以提高电镀生产的一次合格率来提升生产效率,从而实现节能降耗的观点。结合多年生产实际,总结了对电镀生产的全过程实施直接监控时应注意的事项,以避免可预见的、能预防的镀层缺陷。分析了除油、镀液维护、物料添加及操作环节对镀层质量的影响。简单说明了在电镀生产过程中应严格控制和重点注意的一些问题。     

双中心节点的网络软RAID系统的设计与实现

随着计算机技术与网络技术的快速发展,基于网络的分布式存储逐渐成为研究的重点,通过网络提供方便、可靠与大容量的存储服务成为可能。该文设计并实现了双中心节点的网络软RAID系统,并对系统结构、工作原理和技术要点进行了详细介绍。     

Single-event effects induced by medium-energy protons in 28 nm system-on-chip

Single-event effects(SEEs) induced by medium-energy protons in a 28 nm system-on-chip(So C) were investigated at the China Institute of Atomic Energy. An on-chip memory block was irradiated with 90 MeV and70 MeV protons, respectively. Single-bit upset and multicell upset events were observed, and an uppermost number of nine upset cells were discovered in the 90 MeV proton irradiation test. The results indicate that the SEE sensitivities of the 28 nm SoC to the 90 MeV and 70 MeV protons were similar. Cosmic Ray Effects on Micro-Electronics Monte Carlo simulations were analyzed, and it demonstrates that protons can induce effects in a 28 nm SoC if their energies are greater than 1.4 MeV and that the lowest corresponding linear energy transfer was 0.142 MeV cm~2 mg~(-1). The similarities and discrepancies of the SEEs induced by the 90 MeV and 70 MeV protons were analyzed.     

Effect of W on formation and properties of precipitates in Ni-based superalloys

The formation and properties of precipitates in wrought Ni-based superalloys with different W contents during long-term exposure to high temperatures were inves...     

Injectable silk/hydroxyapatite nanocomposite hydrogels with vascularization capacity for bone regeneration

Localized and sustained osteogenic-angiogenic stimulation to bone defects is critical for effective bone repair.Here,desferrioxamine(DFO)was loaded on silk fibroin nanofibers and blended with hydroxyapatite nanorods(HA),forming injectable DFO-loaded silk fibroin-HA nanocomposite hydrogels.The composite hydrogels remained homogeneous distribution of HA with high ratio(60%)and also higher stiffness than that of pure silk fibroin nanofiber hydrogels,which provided stable osteogenic stimulation niches for tissue regeneration.Without the scarify of injectability,the hydrogels achieved slow delivery of DFO for above 60 days,resulting in suitable angiogenesis in vitro and in vivo and better osteogenesis than DFO-free systems.Compared to previous injectable silk fibroin-HA hydrogels,the introduction of vascularization capacity further stimulated the osteogenic differentiation of stem cells and accelerated new bone formation.Quicker and better bone healing were detected at defect sites after the injection of DFO-loaded nanocomposite hydrogels,indicating the effective synergistic effect of osteogenic and angiogenic cues.This work provides a simple and effective strategy of introducing angiogenic cues to bone matrices.We believe that the injectable nanocomposite hydrogels are suitable for the regeneration of bone tissues.