Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

等规聚丙烯β晶型成核剂研究

精选了一系列有机和无机化合物为成核剂,使用砂浴法和热台法制备了一系列不同β晶含量的等规聚丙烯,发现最有效的β成核剂是溶靛素灰 IBL 和溶蒽素金黄 IGK,首次表明β成核剂具有排列紧密的稠球结构特征,且含有硫原子。     

部分种子成分的特征X射线在等效生物材料中衰减的测定

用Ｓｉ（Ｌｉ）探测器实现了Ｎａ、Ｍｇ、Ｓ、Ｃｌ的特征Ｘ射线在有机膜中的相对衰减以及与Ｏ、Ｋ元素的特征Ｘ射线能量相当的Ｘ射线或轫致辐射在有机膜中的相对衰减，分别得出了它们减的数学描述，并把实验得到不同能量的Ｘ射线在有机膜中的质量吸收系数与Ｂｅｒｋｅｌｅｙ的ＯＣＧ软件计算出的结果相比，相关都小于３０％。     

Gain equalization by mitigating self-filtering effect in a chain ofcascaded EDFA's for WDM transmissions

A simple method of alternatively using high-inversion and moderate-inversion erbium-doped fiber amplifiers (EDFA's) in an optical amplifier chain is presented to mitigate the self-filtering effect and equalize both signal power and signal-to-noise ratio (SNR) of multiple wavelength channels in wavelength-division multiplexing (WDM) transmission systems. The performance of the compensated system with alternatively used high- and moderate-inversion amplifiers is compared with the uncompensated ones where only moderate- or high-inversion amplifiers are employed. The result shows that the compensated system has a flatter gain profile, a lesser signal power spread, and SNR degradation     

化学束外延

本文介绍了化学束外延(CBE)的发明和发展,论述了CBE的原理和设备。文中还介绍了最近提出的一种生长机理。     

The relationship among oxygen content, defect distribution and superconductivity in BiSrCaCuO systems

The effect of oxygen content on superconductivity of the 2212 and 2223 phase has been studied. By comparing the excess oxygen, the modulation vector, the XRD patterns, and the electric resistivity of 2212 and 2223 phase samples obtained with different post-annealing conditions, i.e., annealing at 600°C or quenching from 860°C, it was found that the super-conductivity is markedly influenced by both the defect distribution in non-Bi layers and the interstitial oxygens incorporated in the Bi-O layers. A tentative explanation for this is given.     

Observation of atomic steps on CaCO3 crystal surface

By using scanning polarization force microscopy,the deliquescence process and the atomic steps on the cleavage surface of CaCO3 in air were studied in situ.Under an exposure to medium umidity(-57%),the sloiw step movement has been observed.     

Synthesis, characteristics and oxygen-sensitive properties of SrMgxTi 1 − xO3 nanocrystals

SrMg_xTi_{1 - x}O₃ nanocrystals (x = 0.1–0.6) were synthesized by the stearic acid gel method. Powder samples were characterized by X-ray diffraction and X-ray photoelectron (XP) spectroscopy. The results showed that the lattice parameter a and the O 1s XP spectrum changed not only with the Mg content x but also with the grain size d of the samples. The conductivity of a thick film specimen fabricated on an aluminium oxide wafer was investigated in a nitrogen—oxygen atmosphere.     

小方坯连铸机的PLC自动控制

本文对弧型小方坯连铸机工艺与设备进行了分析，介绍了连铸生产的ＰＬＣ控制系统。及其软件设计。