Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

高柔韧性尼龙1010材料的制备

对尼龙1010/NBR/增塑剂体系进行了系统研究,发现在挤出机中环氧扩链剂可以对尼龙进行扩链反应,且环氧树脂对尼龙1010的扩链反应活性较高,扩链效果比较明显;N-丁基苯磺酰胺是尼龙的良好增塑剂,经增塑、增韧后可以使经扩链后的尼龙1010柔韧性有明显提高.采用SEM和TEM对所制备的材料进行了形貌分析,发现用NBR增韧尼龙,对于不同的基体材料,橡胶粒子的形貌有很大不同,粒子由增韧纯尼龙的椭球形变为在增塑尼龙基体中不规则的形状.     

Influence of the preparation conditions on the size and morphology of nanocrystalline lanthanum orthoferrite

Nanocrystalline LaFeO₃ is prepared by the dehydration of coprecipitated lanthanum and iron(III) hydroxides. It is shown that the behavior of the samples during heating and the size distribution of LaFeO₃ nanocrystals can be considerably different depending on the scheme used for coprecipitation of lanthanum and iron hydroxides; independently of the method employed for coprecipitation of the initial compounds, sintering of the samples at 950°C leads to the formation of lanthanum orthoferrite crystals up to 100 nm in size.     

逆向工程技术在机械领域的应用

逆向工程技术已成为联系新产品开发过程中各种先进技术的纽带,并成为实现新产品快速开发的重要技术手段.介绍了逆向工程的概念、技术流程、测量系统、常用软件以及实际应用.     

Perfect Blind-Channel Shortening for Multicarrier Systems

In multicarrier systems, when the order of a channel impulse response is larger than the length of the cyclic prefix (CP), there is a significant performance degradation due to interblock interference (IBI). This paper proposes a blind-channel shortening method in which the equalizer parameter vector is formed by the noise subspace of the received signal correlation matrix so that the output power is maximized. The proposed method can not only shorten the effective channel impulse response to within the CP length but also maximize the output signal-to-interference-and-noise ratio while eliminating the IBI. We point out that the performance depends on the choice of a decision delay and propose a simple method for determining the appropriate delay. We propose both a batch algorithm and an adaptive algorithm and show by simulation that they are superior to the conventional algorithms.     

ADI-FDTD Method With Fourth Order Accuracy in Time

This letter presents an unconditionally stable alternating direction implicit finite-difference time-domain (ADI-FDTD) method with fourth order accuracy in time. Analytical proof of unconditional stability and detailed analysis of numerical dispersion are presented. Compared to second order ADI-FDTD and six-steps SS-FDTD, the fourth order ADI-FDTD generally achieves lower phase velocity error for sufficiently fine mesh. Using finer mesh gridding also reduces the phase velocity error floor, which dictates the accuracy limit due to spatial discretization errors when the time step size is reduced further.