Effect of an abrupt change in pulling rate on microstructures of directionally solidified Al2O3-Er3Al5O12 eutectic and off-eutectic composite ceramics

Directionally solidified microstructures of Al₂O₃-Er₃Al₅O₁₂ eutectic and off-eutectic in situ composite ceramics were explored under abrupt-change pulling rate conditions. Corresponding temperature distributions and interface locations were studied. In eutectic composition, fluctuation of eutectic spacing occurred when the pulling rate increased abruptly. A gradually increase or abrupt increase in eutectic spacing was observed when the pulling rate decreased abruptly. In hypoeutectic and hypereutectic compositions, formation of the primary phases were suppressed when the pulling rate increased abruptly from 10?µm/s to 100?µm/s, while primary phases precipitated when the pulling rate decreased abruptly from 100?µm/s to 10?µm/s. The interface altitude decreased after the pulling rate increased abruptly, but increased after the pulling rate decreased abruptly. The liquid composition restriction (around the eutectic composition) at the eutectic interface plays an important role in the suppression of the primary dendrite and coupled eutectic oxides can be obtained in off-eutectic compositions even under higher solidification rate conditions.     

基于强度场的八球万向节内套结构与静强度设计匹配研究

为了对八沟道等速万向节内套进行结构和静强度设计,从钢球选型出发,对八沟道等速万向节内套进行了结构参数正向设计.对内套危险截面进行了全场静强度设计,以理想静强度场为目标,定量匹配了危险截面静强度的材料、热处理,并对全场静强度设计进行了定量评价.使用MTS静扭转试验机对等速万向节总成进行了静强度扭转试验,并用显微硬度计对内套进行了显微硬度试验以验证理论,结果表明按照基于强度场的机械结构和零部件的静强度设计与匹配方法设计的八沟道等速万向节星形套能够满足强度和功能需求.     

PCB废水总氮处理达标的工艺探讨

对PCB废水总氮的处理,从源头削减、分质收集、分质预处理到末端处理提出了多种方法,着重分析了MAP+管式微滤膜处理氨氮废水、多级组合式RO处理硝态氮废水和A2O+MBR处理综合废水,提出PCB废水总氮达标的组合工艺,项目建成后达到预期效果。     

基于Bayes方法的Al-Mg-Mn合金断裂韧度研究

基于Bayes方法研究了Al-5.2Mg-0.7Mn-0.20Sc-0.1Zr合金的平面应变断裂韧度。结果表明,Al-5.2Mg-0.7Mn-0.20Sc-0.1Zr合金热轧板在L-T和T-L取向KIC值分别为32.66和32.03 MPa·m1/2,平面应变断裂韧度各向异性差别较小。     

超高效液相色谱串联质谱法测定烟草中的噁霉灵残留

为降低烟草中噁霉灵检测中的基质干扰，提高检测灵敏度和和稳定性，通过试验建立了以QuEChERS为样品前处理方法、液相色谱串联质谱仪为检测仪器的烟草中噁霉灵残留检测方法。样品加水浸润后，经丙酮提取、盐析试剂包除水、石墨化炭黑除杂后，采用Agilent ZORBAX 300SB-C8液相色谱柱（2.1 mm×100 mm，1.8 μm）分离，甲醇-水程序洗脱，ESI雾化，串联质谱MRM检测。结果发现，该方法在0.0025~0.0500 mg/L范围内线性良好，决定系数r²=0.9996，定量检测限1.06 μg/L，回收率在90.8%~92.0%之间，相对标准偏差为5.1%。运用该方法测定烟草中的噁霉灵，操作简单，检测精度高，满足CORESTA对烟草农残检测的要求。     

Electrocatalytic Reduction of CO2 to Ethylene by Molecular Cu‐Complex Immobilized on Graphitized Mesoporous Carbon

The electrochemical reduction of carbon dioxide (CO₂) to hydrocarbons is a challenging task because of the issues in controlling the efficiency and selectivity of the products. Among the various transition metals, copper has attracted attention as it yields more reduced and C2 products even while using mononuclear copper center as catalysts. In addition, it is found that reversible formation of copper nanoparticle acts as the real catalytically active site for the conversion of CO₂ to reduced products. Here, it is demonstrated that the dinuclear molecular copper complex immobilized over graphitized mesoporous carbon can act as catalysts for the conversion of CO₂ to hydrocarbons (methane and ethylene) up to 60%. Interestingly, high selectivity toward C2 product (40% faradaic efficiency) is achieved by a molecular complex based hybrid material from CO₂ in 0.1 m KCl. In addition, the role of local pH, porous structure, and carbon support in limiting the mass transport to achieve the highly reduced products is demonstrated. Although the spectroscopic analysis of the catalysts exhibits molecular nature of the complex after 2 h bulk electrolysis, morphological study reveals that the newly generated copper cluster is the real active site during the catalytic reactions.     

Approximate cutting pattern optimization of frame-supported and pneumatic membrane structures

International Journal of Mechanics and Materials in Design - A simple iterative method is presented for cutting pattern optimization of frame-supported and pneumatic membrane structures for...