CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

活性酯硬化水玻璃砂的研究

用焙烧活性砂混制而成的活性酯硬化水玻璃砂与普通酯硬化水玻璃砂相比，强度成倍提高，从而减少水玻璃的加入量，改善水玻璃砂的溃散性。实验证明：原砂的表面活性直接影响在水玻璃砂中水玻璃的加入量，是改善水玻璃砂溃散性的关键之一。焙烧活性砂的水玻璃加入量只要１．５％～２．０％，即能满足实际生产的强度要求。     

氰化氢在终冷塔中气液两相之间转移的研究

分析了煤气中氰化氢的形成,论述了氰化氢在煤气和其冷凝液中的平衡机理,讨论了影响氰化氢相平衡的因素,研究了直接终冷、间接终冷时煤气中氰化氢的转移情况。     

聚碳酸酯的吹塑成型

简介聚碳酸酯吹塑容器的特性与用途,着重分析其吹塑(包括挤出吹塑、共挤吹塑和注射吹塑)成型的机械(螺杆、机筒、型坯机头与吹塑模具)设计要点及工艺条件。     

含CO2气体混合物在60℃时的混合性质

测定了６０℃和２－６００ｂａｒ时由ＣＯ２和Ｈｅ、Ａｒ、ＳＦ６以及ＣＨＦ３组成的等分子二元混合物的压缩因子，根据纯物质和混合物的压缩因子计算了压力混合效应和过剩体积。对于真实气体混合性质的描述，本文采用五参数的ＢＡＣＫ方程，方程计算值与实验值符合较好。     

纤维素衍生物液晶相转变和织态结构

本文综述了纤维素衍生物液晶态相转变和织态结构。描述了纤维素衍生物从各向同性态向液晶态的转变过程和液晶态的织构特征。讨论了溶液浓度和温度对液晶相织构的影响。探讨了各种因素,如溶剂、取代基含量、外加力场和外加磁场等对液晶相的形成及织态结构的影响。     

Relative image similarity learning with contextual information for Internet cross-media retrieval

With the fast explosive rate of the amount of image data on the Internet, how to efficiently utilize them in the cross-media scenario becomes an urgent problem. Images are usually accompanied with contextual textual information. These two heterogeneous modalities are mutually reinforcing to make the Internet content more informative. In most cases, visual information can be regarded as an enhanced content of the textual document. To make image-to-image similarity being more consistent with document-to-document similarity, this paper proposes a method to learn image similarities according to the relations of the accompanied textual documents. More specifically, instead of using the static quantitative relations, rank-based learning procedure by employing structural SVM is adopted in this paper, and the ranking structure is established by comparing the relative relations of textual information. The learning results are in more accordance with the human’s recognition. The proposed method in this paper can be used not only for the image-to-image retrieval, but also for cross-modality multimedia, where a query expansion framework is proposed to get more satisfactory results. Extensive experimental evaluations on large scale Internet dataset validate the performance of the proposed methods.