Experimental Research on Erbium-doped Superfluorescent Fiber Source

The effects of the variations in fiber length, fiber mirror reflectance on efficiency and output power are experimentally investigated for erbium-doped double pass backward superfluorescent fiber sources (SFSs). The influence of fiber length on mean wavelength stability (MWS) has also been demonstrated. By incorporating a short section of un-pumped erbium-doped fiber (EDF) at the output port, the pump power dependent on MWS becomes independent of pumped EDF length. This is a novel phenomenon that hasn‘t been reported up to now,and should be helpful to SFS fabrication and theory analysis. By using a fiber Michelson interferometer as spectrum slicing component,a multi-wavelength fiber source (MWFS) with ～20 channels (from 1542nm to 1559nm) is got. The MWFS has a channel spacing of ～0. 8 nm which satisfies ITUstandard. The intensity fluctuation among channels is less than 0.5dB,and the extinction ratio of all channels is above 14dB. This kind of MWFS should be useful to wavelength division multiplexing systems.     

关于海面无线传播模型的探讨

现有文献中一般都认为海面环境的无线传播模型近似于自由空间传播模型，但在实际测试中发现，自由空间模型预测值与实测值差别较大，不能很好地解释此类环境的信号传播。笔者根据多次海面覆盖测试的数据，分析并拟合出了新的海面传播模型。     

Preirradiation grafting of acrylic and methacrylic acid onto polyethylene films: Preparation and properties

The method of preirradiation grafting of acrylic acid and methacrylic acid onto polyethylene films was studied. The trapped radicals and hydroperoxides or diperoxides appeared to be able to induce graft polymerization. Mohr's salt was added to depress homopolymerization. The influences of crystallinity, dosage, and storage period on the grafting behavior were investigated from the viewpoint of practical application. At elevated temperature, the degree of grafting increased rapidly with reaction time initially, and then leveled off to the value of final percent grafting. Dosage and storage periods had greater extent of influence on the final percent grafting of LDPE than on that of HDPE. Electrical properties, transport properties, and mechanical properties were measured to compare the differences between acrylic-acid-and methacrylic-acid-grafted copolymer films. It was found that the properties of methacrylic-acid-grafted copolymer film was superior to those of acrylic-acid-grafted copolymer film, especially in electrical conductivity. The KOH diffusion test confirmed that grafting occurred not only on the surface but also in the interior of the polymer matrix, and the grafting is believed to proceed from the surface to the interior of the matrix.     

Traveling-wave piezoelectric linear motor Part I: the stator design.

A new type of piezoelectric linear motor incorporating a traveling wave has been developed. The linear motor is comprised of a stator and a carriage. The stator design, which consists of a meander-line structure and gear teeth mounted on the meander-line structure, is the focus of this article. The meander-line structure is constructed with bimorph actuators arranged in a line. These actuators are driven by two phased sets of alternating current (ac) in order to generate a traveling wave. The traveling wave is transferred to the gear teeth, by which the carriage is driven. Modeling of the stator is derived by use of a strain energy method. The performance of various materials is evaluated by analytical and experimental methods. The analytical and the experimental results are quite approximate. Modal analysis is investigated using ANSYS. Appropriate modes associated with ultrasonic levels of resonant frequency are selected to obtain desired motion and to enhance the output performance. Surface speed for various applied input voltage are studied and indicate a nearly linear relationship. The stator in combination with the carriage makes up the linear motor.     

IF板与08Al板的成形性能研究

通过模拟成形性试验，对新型超深冲用IF钢板和传统冲压用08Al钢板的冲压成形性能进行了研究．结果表明：IF板的拉深性能、扩孔性能、胀形性能以及“拉深-胀形”复合性能等均优于08Al板，其中，扩孔性能和平面各向异性的改善最为显著；各项试验中，IF板的成形力普遍小于08Al板。     

Optimum power-saving method for power MOSFET width of DC/DC converters

An optimum power metal-oxide-semiconductor field effect transistor (MOSFET) width technique is proposed for enhancing the efficiency characteristics of switching DC-DC converters. By implementing a one-cycle buck DC-DC converter, it is demonstrated that the dynamic power MOSFET width controlling technique has a much improved power reduction whether the load current is light or heavy. The maximum efficiency of the buck converter is ~92% with a 3% efficiency improvement for the heavy load condition. The efficiency is further improved by ~16% for the light load condition as a result of the power reduction from the large power MOSFET transistors. Also proposed is a new error-correction loop circuit to enable a better load regulation than that of previous designs. Compared with the adaptive gate driver voltage technique, the optimum power MOSFET width can achieve a significant improvement in power saving. It is also superior to the low-voltage-swing MOSFET gate drive technique for switching DC-DC converters     

加油站油品用体积交接存在的问题及建议

叙述了目前加油站在实行按任意温度下的体积交接，由于未考虑油品体积随温度、压力、密度的变化，出现了零售损耗很大的问题。建议加油站在现阶段采用“准标准体积”交接；在由体积转换为质量计算加油站损溢时，使用油库当月发出的平均密度；当财会核销损溢时，不使用盘存的体积和固定密度进行计算的方法，而使用实际盘点的质量数，以真实反映加油站的当期损溢。     

机械CAD课程教学改革探讨

文章分析了机械CAD技术的特点以及国内CAD教学的现状,提出了机械CAD教学改革的方法,并从教学体系、教学方法、考试方式等方面进行了探讨.     

猪场沼气工程改造技术研究

一、概况南平市种猪场位于延平区浆甲村 ,距市区 13km ,地处 316国道旁 ,面临沙溪口库湾边。年存栏猪760 0头 ,其中母猪 60 0头 ,后备种猪 2 5 0 0头 ,商品猪 4 5 0 0头 ,是闽北集种猪、商品猪生产及科研繁育于一体的副食品基地之一。该场日排猪粪便污水约140t,未建沼气工程前 ,直接排入水库 ,严重污染水体。1999年 ,种猪场采用厌氧发酵技术 ,处理猪粪便污水 ,兴建 4× 2 0 0m3沼气工程 ,技术落后 ,基本属于农村户用水压式沼气池的简单放大 ,猪粪便污水直接进入厌氧发酵池 ,出水直接排入水库。工程设计的主要问题是 :1 不设前处理装置 ,冲洗…