子母车系统效率分析与验证

在子母车系统中,研究一台母车配合两台子车在同层进行复合作业的效率问题,提高系统作业效率计算的准确性,优化系统整体布局和物流设备的选择。首先分析一台母车配合两台子车在同层的循环复合作业过程;然后结合子母车的运动特性得到其作业效率计算模型;最后采用MATLAB工具计算效率模型分别在随机组合作业对和FEM9.851标准作业对的作业效率,通过对比验证,两种循环作业的效率绝对偏差符合工程实际。在工程实际中可以参照FEM9.851标准作业对代替随机组合作业对进行子母车系统的效率计算。     

基于DSP的多元数据同步采集与存储系统的设计与实现

从硬件和软件两个角度出发,介绍基于DSP的多元数据同步采集与存储系统的组成、工作模式以及功能的测试。系统主要由上位机和数字采集与存储单元组成,其中数字采集与存储单元的硬件部分包括电源模块,值班电路模块,数据采集模块,数据存储模块,时钟同步模块。系统采用DSP作为中央处理芯片,利用经过同步后的秒脉冲作为触发信号,实现同步数据采集。以CF卡作为存储介质,实现数据自容式存储。软件部分实现自检、同步、数据采集存储功能。经过测试,系统工作稳定,功能正常,同步精度在100ns以内。     

PGNAA技术对铜精矿元素及水分进行在线检测的应用研究

目前对铜精矿元素含量及水分的检测大多基于试验室取样分析，存在取样代表性差，分析时间长等问题。针对上述问题，采用基于瞬发γ中子活化分析（PGNAA）技术设计的在线分析仪对国内某铜精矿样品进行主要元素含量及水分在线检测研究。结果表明：铜精矿中各主要元素含量及水分检测量线性相关性良好，满足指导铜精矿生产的要求。     

某进口固体废物“铁精粉”的鉴别方法探析

为了确保不进口污染环境的固体废物，针对某冒充铁精粉的进口固体废物，通过外观、成分、物相分析进行了系统的鉴别。确定样品主要为经研磨加工的氧化铁皮，属于禁止进口的固体废物——轧钢产生的氧化皮。     

An engineering method for complex structural optimization involving both size and topology design variables

This work presents an engineering method for optimizing structures made of bars, beams, plates, or a combination of those components. Corresponding problems involve both continuous (size) and discrete (topology) variables. Using a branched multipoint approximate function, which involves such mixed variables, a series of sequential approximate problems are constructed to make the primal problem explicit. To solve the approximate problems, genetic algorithm (GA) is utilized to optimize discrete variables, and when calculating individual fitness values in GA, a second-level approximate problem only involving retained continuous variables is built to optimize continuous variables. The solution to the second-level approximate problem can be easily obtained with dual methods. Structural analyses are only needed before improving the branched approximate functions in the iteration cycles. The method aims at optimal design of discrete structures consisting of bars, beams, plates, or other components. Numerical examples are given to illustrate its effectiveness, including frame topology optimization, layout optimization of stiffeners modeled with beams or shells, concurrent layout optimization of beam and shell components, and an application in a microsatellite structure. Optimization results show that the number of structural analyses is dramatically decreased when compared with pure GA while even comparable to pure sizing optimization.     

YSZ/MoS2 self-lubricating coating fabricated by thermal spraying and hydrothermal reaction

Thermal sprayed ceramic coatings have extensively been used in components to protect them against friction and wear. However, the poor lubricating ability severely limits their application. Herein, yttria-stabilized zirconia (YSZ)/MoS₂ composite coatings were successfully fabricated on steel substrate with the combination of thermal spraying technology and hydrothermal reaction. Results show that the synthetic MoS₂ powders are composed of numbers of ultra-thin sheets (about 7 ~ 8?nm), and the sheet has obvious lamellar structure. After vacuum impregnation and hydrothermal reaction, numbers of MoS₂ powders, look like flowers, generate inside the plasma sprayed YSZ coating. Moreover, the growing point of the MoS₂ flower is the intrinsic micro-pores of YSZ coating. The friction and wear tests under high vacuum environment indicate that the composite coating has an extremely long lifetime (>?100,000 cycles) and possesses a low friction coefficient less than 0.1, which is lower by about 0.15 times than that of YSZ coating. Meanwhile, the composite shows an extremely low wear rate (2.30?×?10^?7 mm³ N^?1 m^?1) and causes slight wear damage to the counterpart. The excellent lubricant and wear-resistant ability are attributed to the formation of MoS₂ transfer films and the ultra-smooth of the worn surfaces of hybrid coatings.     

低觉醒脑电识别与唤醒的可穿戴系统研究

为智能化地识别警戒作业人员出现的低觉醒、注意力下降的生理状态，本文介绍了一种基于FPGA和脑电信号处理的低觉醒状态检测与唤醒系统，系统通过传感器从大脑头皮采集脑电信号，转换为数字信号，经傅里叶变换获取了脑电信号的θ相对能量、α相对能量、重心频率、谱熵等4个特征量，由4个特征量表征低觉醒状态并运用支持向量机对低警戒状态进行识别，当识别出低觉醒状态时采用声音报警模块发出声音，唤醒警戒作业人员。设计系统能够较好地识别出低觉醒状态，识别率达90.8%，可为提高警戒作业工作绩效提供一种可穿戴的智能装备。     

碳基采暖电热材料研究进展

近几年,由于节能与环保的需求,电取暖的方式得到大力的推广,电热材料的研究与应用受到人们广泛的重视。非金属碳基电热材料是新型的节能型电热采暖材料,本文重点对影响非金属碳基电热材料中的炭黑基电热材料、碳纤维基电热材料、碳晶电热材料电热性能的因素及相关应用进行了综述。     

2A12铝合金化学铣切加工工艺探讨

为了精确加工2Al2铝合金,探讨了化铣时间和温度对其化铣速率及表面粗糙度的影响,采用现代技术对化铣工件的力学性能进行了测试与分析.结果表明:延长非化铣部位保护胶固化时间并使保护部位向非加工面位移3～5 mm可很好地解决未化铣区域的腐蚀问题;随化铣时间的延长,化铣速率降低,且化铣温度与化铣速率呈现正相关性;化铣表面的粗糙度随化铣时间的延长而增加,随化铣温度的升高呈先减小后增加的趋势;化铣后材料的抗拉强度和屈服强度均有所提高.