高质量的一级光栅1．55μmDFB激光器

本文详细叙述了ＤＦＢ激光器的设计要点和新的工艺。采用一级全息光栅和二步液相外延法批量研制出高稳定单纵模工作的１．５５μｍ分布反馈激光器（ＤＦＢ—ＬＤ）。外延片成品率＞４０％。器件特性：２５℃时阈值电流２０ｍＡ，单面光功率＞１０ｍｗ，主边模抑制比ＳＭＳＲ达４３ｄＢ（λ／４相移光栅），谱线宽度△ν－２０ｄＢ＝０．３ｎｍ，调制速率＞１．８ＧＨｚ。可靠性测试显示：高温监测光谱稳定，２５°Ｃ时阈值退化率△Ｉｔｈ／ｔ＜０．３ｍＡ／ｋｈ，对应器件预估寿命将超过１０万ｈ。     

Enhancement of oxide break-up by implantation of fluorine inpoly-Si emitter contacted p+-n shallow junctionformation

In this study, it is demonstrated that the incorporation of fluorine can enhance poly-Si/Si interfacial oxide break-up in the poly-Si emitter contacted p⁺-n shallow junction formation. The annealing temperature for breaking up the poly-Si/Si interfacial oxide has been found to be as low as 900°C. As a result, the junction depth of the BF₂-implanted device is much larger than that of the boron-implanted device     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry     

锌钾硼对甜菜产质量效应及最佳施肥措施的研究

本文利用最优回归设计“310”方案,研究了黑土地甜菜 Zn、K_2O、B的效果及合理施用问题。得出甜菜块根产量、含糖、产糖量、灰分 K 和有害 N 与 ZnK_2O、B 肥回归关系显著的回归模型,分析了 Zn、K_2O、B 对上述五个指标的效应,明确了 Zn 是影响各项指标的主要因子,并采用频率筛选法,提出了兼顾上述五项指标的优质高产施肥措施。     

高扬的旗帜——博山电机厂集团股份有限公司精神文明建设纪实

建厂已近60年的博山电机厂,在企业发展的历史上曾经有过辉煌:40年代,作为军工厂,在抗日战争的烽火和解放战争的硝烟中为新中国的解放事业做出了很大的贡献;50年代,作为全国八大电机厂之一,又为新中国的建设事业提供了许多优良的产品,而且作为汽车电机、直流微电机、交流     

SIMATIC S5—115U可编程控制器

本文通过对SIMATIC S5—115U可编程控制器性能的简介,简述国外PC技术的现状和发展,并提出对PC国产化的看法.