Effect of heating and acidic pH on characteristics of wheat gluten suspension

The effects of different pH treatments with and without heating on the characteristics of wheat gluten suspension was investigated. At pH 1, maximum changes in colour were observed with a concurrent 65% decrease in protein free-thiol content compared to the control gluten. The SDS-Extractability of protein (SDS-EP) chromatogram eluted at lower retention time and the presence of bands at the top lane even during reducing conditions in SDS-PAGE gel suggested complex formation involving bonds other than disulphides. An increase in the free-amino group content and the presence of an additional peak at a higher retention time in the SDS-EP chromatogram was suggestive of hydrolysis. At pH 2 and 3, similar decreases in SDS-EPs and free-thiol content indicated formation of complexes. When heated, the free-thiol content of the dispersions increased compared to the non-heated dispersions indicating disruption of disulphide bonds with changes in gluten structure and size distribution.     

Structure of lean premixed hydrogen-air flames in an annular microcombustor

Self-sustainable combustion and narrow stability limits are the most critical issues in microcombustors (length scale 1 mm) as increased heat losses can lead to thermal quenching of the flame. Hydrogen is a potential fuel for microcombustion due to its high specific energy and wide flammability limits. This work focuses on the lean premixed hydrogen-air flames stabilized in a newly developed annular microcombustor. Detailed axisymmetric numerical calculations involving multistep kinetics, multicomponent mass-heat transport, conjugate heat transfer, and thermal radiation in gas and solid media are performed. It has been shown that flame stabilization occurs by preheating even though wall temperatures are higher than the autoignition temperature. Results unravel the importance of H radical reactions in the kinetics of microflames in low- and high-temperature regions of the microcombustor.     

Structural and Luminescence Studies on Barium Sodium Borosilicate Glasses Containing Uranium Oxides

Barium sodium borosilicate glasses containing different amounts of uranium oxides were prepared by conventional melt quench method and investigated for their structural aspects by ²⁹Si and ¹¹B MAS NMR technique combined with steady‐state luminescence and lifetime measurements. Based on MAS NMR studies, it is confirmed that uranium ions act as network modifier up to 15 wt% and beyond which a separate uranium containing phase is formed. From the luminescence studies, it is inferred that uranyl species is in a highly distorted environment. For more than 15 wt% uranium oxide incorporation, weaker U–O–U linkages are formed at the expense stronger U–O–Si/B linkages, as suggested by the excited state lifetime value of the uranyl species as well as red shift in emission peak maximum. For glass samples containing more than 25 wt% uranium oxides, crystalline barium uranium silicate gets phase separated from glass matrix as confirmed by XRD studies.     

Numerical Analysis of Bird Impact on Glass-Reinforced Leading Edge of an Aircraft Wing

The paper describes the methodology of modeling and simulation of bird impact mechanism of GLARE laminate structures. The bird is modeled using Lagrangian concept. Explicit finite element techniques have been developed to simulate the impact mechanics. The study involves deeper understanding of impact dynamics and contact mechanics. The bird impact analysis has been carried out on typical configuration of GLARE 3/2, 4/3, 5/4, 6/5, 7/6 and 8/7. The results of stress propagation and material deformation at high strain rate have been obtained. Results from the numerical analysis are compared with experimental results, and the material is found to be capable of absorbing the impact energy. The results also show that the bird material model chosen to simulate for carrying out impact mechanics analysis is found to be capable of capturing most of the complex behavior exhibited by functional structural material GLARE.     

Ilmenite phase nickel titanate nanowhiskers as highly sensitive LPG sensor at room temperature

The NiTiO₃ nanoparticles with ilmenite phase were synthesized by the sol gel method and investigated for sensing of various volatile organic compounds. The resistive type sensing by NiTiO₃ towards LPG was not reported earlier where the sensor showed fair response towards hydrogen sulfide gas, but the sensitivity towards LPG was very high. The response % for 150 ppm of LPG was approximately 3200% at room temperature. The high response towards LPG was due to the presence of some amount of rutile TiO₂ in the composites. The response and recovery times of these sensors were very less (about 2 s) which could be attributed to the whiskers like structure of NiTiO₃.     

Modelling of wind energy‐based microgrid system implementing MMC

Nowadays, renewable energy systems have come up with more potential in power generation so as to meet the power demand. Among all the renewable systems, the wind energy generating system is believed to be at the peak. However, the wind energy‐based microgrid system is associated with many problems such as fluctuations in output voltage due to the fluctuated wind speeds and harmonics generations in the system. To address these issues, this article proposes a new method in order to achieve harmonic mitigation across its output by maintaining constant voltage. Nevertheless, particular attention has been given to the form and function of modular multilevel converter with multi‐winding transformer connected to the grid. Modular multilevel converter has been implemented with an advanced voltage controller tuned to control the voltage at its output. Also, a new system topology has been introduced with two wind turbines that are interconnected to multi‐winding transformer through asynchronous generators. The proposed system has been implemented with constant and variable wind speeds, and their respective results have also been analysed. The proposed scheme shows its effectiveness by theoretical calculations, verified by simulation and experimental results. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of rice analogues using extrusion technology

Rice is considered as staple food in many parts of the world. An issue of concern is the breakage of rice kernels in milling processes, and these broken kernels are not generally accepted by consumers. These broken kernels can be mixed with some desired additives to improve their quality and extruded for the preparation of reconstituted rice kernels or rice analogues. Various studies have been conducted for the preparation of the rice analogues in the past few decades, and recently attempts have been made to fortify these analogues with protein, certain vitamins and minerals. The main features such as colour, shape, size, texture, and cooking characteristics and cooking time of these rice‐like grains can be tailored to the requirements of specific applications by modification of the extrusion parameters. Various organisations, such as Wuxi NutriRice Co. (DSM/Buhler) and China National Cereals, Oils and Foodstuffs Corporate (COFCO), Superlative Snacks Inc., Vigui and PATH, have utilised this technique to prepare fortified and reconstituted rice. Studies have shown that it is possible to improve the nutritional quality of rice by fortified rice analogues. This article reviews research results of the many approaches to the formation of fortified rice analogues by extrusion‐based technologies.