秦山核电厂蒸汽发生器水位控制试验

简要介绍了蒸汽发生器水位控制系统的运行方式和试验方法。试验项目包括旁通阀控制试验、主给水阀控制试验和旁通阀与主给水阀的切换试验。文中给出了试验结果,即在液位扰动和核动率扰动时,蒸汽发生器液位的变化过程。经过两个月的运行和瞬态试验,证明蒸汽发生器水位控制系统满足设计要求。     

化工重大技术装备工作"十五"的成绩与"十一五"的任务

重大技术装备的制造水平是一个国家综合实力的直接体现,因此从上个世纪八十年代初开始,历届国务院领导人均兼任国家重大技术装备领导小组组长,通过推进重大技术装备的发展,促进     

High voltage (>1kV) and high current gain (32) 4H-SiC power BJTs using Al-free ohmic contact to the base

This letter reports the design and fabrication of 4H-SiC bipolar junction transistors with both high voltage (>1kV) and high dc current gain (/spl beta/=32) at a collector current level of I/sub c/=3.83A (J/sub c/=319 A/cm/sup 2/). An Al-free base ohmic contact has been used which, when compared with BJTs fabricated with Al-based base contact, shows clearly improved blocking voltage. A specific on-resistance of 17 m/spl Omega//spl middot/cm/sup 2/ has been achieved for collector current densities up to 289 A/cm/sup 2/.     

Bioprocess applications of model-based estimation techniques

The last decade has seen the development of a number of approaches for estimating those variables which are difficult to measure on-line in industrial process situations. Whilst a range of techniques is available, a common element is the use of process knowledge in the form of a system model. In the case of bioprocess systems, although a large range of models has been presented in the literature, their use in estimation schemes on an industrial scale has been limited. A number of reasons can be identified for their low level of utilisation. Of particular significance is the uncertainty which exists in quantifying system performance and the process-model mismatch which inevitably results. The level of ‘pre-defined model’ uncertainty, together with the knowledge gained during the course of the fermentation, serves to dictate estimator structure. The paper considers a range of estimation strategies and contrasts, through industrial applications, their performance characteristics and utility.     

A polymerizable photoredox initiation system for vinyl photopolymerization

A polymerizable photoredox system consisting of 4-methacryl oxbenzophenone (MABP) and N,N-dimethlaminoethyl methacrylate (DMAEMA) used for the photopolymerization of acrylonitrile (AN) was studied. It was found that the polymerization rate is proportional to the 0.93th power for the AN concentration, the 0.28th power for the MABP concentration, and the 0.25th power for the DMAEMA concentration. The overall activation energy of the polymerization obtained is 30.43 kJ/mol. The recorded ESR spectrum indicates that the excited-state MABP abstraets hydrogen mainly from the methyl group of the dimethylamino moiety. The comparison of the initiation ability of polymeric MABP or polymeric DMAEMA with their monomeric forms has also been done and the results indicate that in good solvents P (MABP) has a much higher initiation ability than that of monomeric MABP, but monomeric DMAEMA and P (DMAEMA) display almost the same initiation ability. In poor solvent, the initiation ability of P (MABP) is not so obviously higher than that in good solvents. The result of UV analysis of P (AN) initiated by the MABP–DMAEMA system indicates that both MABP and DMAEMA not only initiate the photopolymerization of AN, but also enter into P (AN) polymer chains. © 1994 John Wiley & Sons, Inc.     

STRUCTURE REPRESENTATION OF THE SPECIFIC FRACTIONS FROM PINGSHUO COAL

Basic data of four fractions, PM₁, PM₆, PM₇and PM₈, derived from Pingshuo bituminous coal were obtained by ultimate analyses, mean molecular weight measure, GC/MS, ¹³C-NM R, ¹H-NM R and FTIR technigues. A method of calculating the average molecular parameters of the fractions is introduced. Based on the calculated parameters, the molecular structure models of the fractions of PM₆, PM;and PM₈are constructed. Significant structural information about the saturated hydrocarbon and aromatic hydrocarbon with heteroatom groups is given also.     

Using thermally stimulated currents to find defective capacitors

BaTiO₃ multilayer capacitors with a nominal capacitance of 3.5nF have been carefully measured using the thermally stimulated current (TSC) technique. When a 300V polarization voltage is applied at room temperature, a new TSC peak appeared in defective sample A after it has been immersed in water. No new peak was found in good-quality sample B after a similar treatment. The accelerated life test shows that sample A hasa much shorter life than sample B in terms of insulation resistance.     

Effects of α‐form or β‐form nuclei on polymorphic crystalline morphology of poly(butylene adipate)

The effects of α‐form and β‐form nuclei on polymorphic morphology of poly(butylene adipate) (PBA) upon recrystallization from the molten state up to various T_max values were examined by differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD) and polarized light microscopy (PLM). In this study, PBA with complex melting and polymorphism behaviour was used as a model for examining different types and extents of residual nuclei. As the PBA initially containing the sole α‐crystal was brought to a molten state of various T_max, the extents of trace α‐form crystal nuclei varied and were dependent on T_max. Furthermore, it did not matter whether, initially, the PBA contained α‐ or β‐form crystals (or both) because only a single type of α‐nuclei could be left upon treatment to the molten liquid state at T_max. Therefore, only the α‐crystal in PBA had ‘memory capacity’ in the molten liquid state while the β‐crystal did not. This was so because the latter had been completely transformed into the solid state prior to being heated into a liquid. PBA crystallized before α‐nuclei could be packed into α‐crystal, regardless of the crystallization temperature (T_c). For recrystallization from molten PBA without any nuclei, the crystalline polymorphism was correspondingly influenced by T_c. Copyright © 2005 Society of Chemical Industry