三种检测方法对比水中莠去津残留研究

介绍三种方法检测水中莠去津残留,水样经过二氯甲烷液液萃取后,可分别采用液相色谱法、气相色谱法(NPD检测器、ECD检测器)三种方法进行检测,分别对比了三种色谱分析方法的实验条件和实验方法及如何制作标准曲线,并进行了精密度、回收率及检出限实验.结果表明,三种方法均可行,均适用于生活水和水源水中莠去津的检测.     

Au-Ag-Si新型中温共晶钎料的研究

根据合金相图的基本原理,分析了Au-Ag-Si系相图,研制出熔化温度在400℃～500℃的共晶钎料合金.通过钎料合金与Ni板的润湿性测试和润湿后界面的微观组织分析.结果表明:Au-Ag-Si系钎料对于纯Ni具有良好的漫流性和润湿性,在450℃～500℃范围内,可以对Ni板进行钎焊.     

N3-Kethoxal-Based Bioorthogonal Intracellular RNA Labeling

There is growing interest in developing intracellular RNA tools. Herein, we describe a strategy for N₃-kethoxal (N₃K)-based bioorthogonal intracellular RNA functionalization. With N₃K labeling followed by an in vivo click reaction with DBCO derivatives, RNA can be modified with fluorescent or phenol groups. This strategy provides a new way of labeling RNA inside cells.     

化学交联聚酰亚胺隔膜增强锂离子电池性能研究

隔膜作为锂离子电池的重要组成部分,用于阻隔阴极和阳极直接接触,同时为锂离子在电极间的传输提供有效通道。聚酰亚胺隔膜因其具有充放电循环寿命长、机械强度适中、良好的电绝缘性能以及自熄能力等优点,而受到广泛关注。以对苯二甲胺作为交联剂,将聚酰亚胺隔膜进行化学交联,研究了交联时间与隔膜形貌、结构及性能之间的构效关系。随着交联时间的增加,隔膜的孔隙率和吸液率逐渐降低,电解液接触角和机械强度逐渐增大。电化学测试表明,随着交联时间的增加,隔膜的本体阻抗逐渐增大,进而离子电导率逐渐降低,而交联隔膜的界面阻抗均远小于未交联隔膜,且交联隔膜的电化学窗口也均大于未交联隔膜。通过组装半电池测试发现,交联隔膜所组装电池的倍率性能和循环性能均优于未交联隔膜,当交联时间为48 h时,电池性能表现最优,循环100次以后,放电比容量为130.2 mA·h/g,容量保留率为91.1%。     

准贝氏体铸钢正火热处理工艺的研究

研究了准贝氏体铸钢不同奥氏体温度正火对其组织与力学性能的影响 ,结果表明 ,随奥氏体化温度的提高 ,准贝氏体铸钢的强韧性改善 ,在 10 4 0℃正火 ,准贝氏体铸钢具有最佳强韧性配合。分析了高温奥氏体化正火强韧性提高的原因。     

Effect of laser fluences on the structure of carbon nitride films deposited by direct current plasma assisted pulsed laser ablation

Carbon nitride films were deposited by direct current plasma assisted pulsed laser ablation of a graphite target under a nitrogen atmosphere at room temperature. The surface morphology, composition and bonding structure of the deposited films were characterized by atomic force microscopy (AFM), Fourier transform infrared (FTIR) spectroscopy, Raman, and X-ray photoelectron spectroscopy (XPS). The effect of laser fluences in the range 0.5–3 J/cm² on the surface morphology, composition and bonding structure of the carbon nitride films were systematically studied. As laser fluence is increased, AFM results show a great decrease in the surface roughness of carbon nitride films. FTIR and XPS results indicate an increase in the N/C ratio and the content of N atoms bonded to sp³ C, as well as a decrease in the content of H atoms and the content of N atoms boned to sp² C in the deposited films, and Raman spectra indicate an increase in the content of disordered sp² C atoms and the sp² cluster size. The increase in the film density and the decrease in the particle fraction contribute to the decrease of surface roughness with increasing laser fluence.     

逆向工程技术在复杂铸造模具制造中的应用

首先介绍了逆向工程技术与传统制造技术的区别,然后着重讨论利用逆向工程技术快速制造复杂铸造模具的过程及工艺路线,同时给出一些具体应用实例。最后得出与传统制造方法相比具有效率高、成本低、操作简单等优点的结论。     

聚铝溶液pH值及盐基度的相关性研究

为聚铝溶液进行了ＰＨ值和盐基度的分析和估算,给出了聚铝溶液的极限ＰＨ值和极限盐基度与总溶解铝浓度的关系曲线,最终计算结果表明：在平衡条件下,聚铝溶液的ＰＨ值和盐基度具有相关性,即当基中一个参数发生变化时。另一个参数必然要发生相应的改变。     

红河州磷肥厂6万t／a半水－二水法磷酸装置试生产情况

主要介绍了红河州磷肥厂引进的６万ｔ／ａ半水一二水法磷酸生产技术及三年来该装置的试生产情况，着重介绍了针对试生产中存在问题进行的技术改造。现该套装置运行正常，生产指标已接近设计值。