富氧燃烧技术在梭式窑中的应用

研究了富氧燃烧技术对梭式窑烧成的影响.研究结果表明,随着氧浓度从21%-30%的逐渐增加,CO总浓度和NO总浓度都先明显下降,后缓慢上升;节能效果在初始段较为明显,而后效果不明显;而实际烟气量与氧浓度成反比,与过剩空气系数成正比.     

调整水量法(代用法)测定水泥标准稠度用水量方法的改进

结合兰州市的水泥标准稠度用水量方法测定 (代用法 )的实例 ,分析代用法测定标准稠度用水量的缺点 ,并对此方法提出了一些改进措施     

Two-dimensional symmetric multimode interferences in silicon square waveguides

Symmetric interference in two-dimensional multimode silicon waveguides is experimentally investigated. For a 100/spl times/100 /spl mu/m/sup 2/ cross section, 2700-/spl mu/m-long waveguide fabricated on silicon-on-insulator substrate, an 8/spl times/8 matrix of replicated images with high contrast ratio is demonstrated for 1530-1570 nm wavelength range. Symmetric interference results in reduced device length, and the actual device length is consistent with the theoretical expectation. The device also exhibits stable imaging in terms of good loss uniformity, and low wavelength and polarization dependencies among the replicated images.     

Growth of highly orientated strontium barium niobate thin films on Si substrates through the sol–gel process using a K: SBN template layer

We report the growth of highly C-axis orientation of Sr _x Ba_1−x Nb₂O₆ (SBN) thin films on p-type (100) Si substrates by using a potassium-substituted SBN template layer with the sol–gel method. The crystallization of SBN thin films was found closely related to the potassium ion doping concentration and the postannealing temperature of the K-SBN template layer. Secondary ion mass spectrometry analysis showed that potassium elements were accumulated at the interface of the template layer and silicon substrate. SBN films postannealed at 750 °C with K-SBN template layer has a smaller full width at half maximum of X-ray rocking curve of 2.45° than that of 5.40° for the pure SBN films. By introducing a template layer, the surface morphologies of SBN films fabricated on silicon substrate were greatly improved.     

乳化型轧制液的质量标准研究

对国内目前所使用的冷轧薄钢板(汽车钢板)轧制液母液和乳化液的质量指标及常用试验评定方法进行了考察，并对产品的性能要求进行了研究与分析，制订出一套标准以供参考，包括乳化液稳定性、润滑性、防锈性、抗泡性、使用周期及粘度、闪点等性能。     

压电量测系统漏电影响分析

本文通过对压电量测系统等效电路图的逐步简化,得出矩形脉冲信号的漏电方程;并对系统在各种情况下的时间常数,漏电相对误差进行了计算,最后就系统在校准和现场测试中经常碰到的几种情况,进行了定量估算,从而解决了压电量测系统在使用中的一些具体问题。     

Successive interference cancellation for multiuser asynchronousDS/CDMA detectors in multipath fading links

There has been an increasing interest in the use of code-division multiple access (CDMA) in cellular mobile and wireless personal communications. The choice of such multiaccess technique is attractive because of its potential capacity increases and other technical factors such as privacy and multipath rejection capabilities. However, it is well known that the performance of CDMA can be significantly degraded due to cochannel interference (CI) and the near-far effects. We consider the performance of direct-sequence (DS)-based CDMA over fading channels that are modeled as slowly varying Rayleigh-fading discrete multipath channels. Specifically, we propose and analyze an adaptive multistage interference cancellation strategy for the demodulation of asynchronous DS spread-spectrum multiple-access signals. Numerical results show that the proposed multistage detector, which alleviates the detrimental effects of the near-far problem, can significantly improve the system performance     

彩色PDP用玻璃基板

本文讨论了彩色ＰＤＰ现用钠钙玻璃的热稳定性，指出由于这种玻璃在热处理过程中易变形和收缩，因而不适合作大面积彩色ＰＤＰ基板材料，介绍了彩色ＰＤＰ基板玻璃的制造方法和特点。最后介绍了日本旭硝子公司和美国康宁公司各自为彩色ＰＤＰ新开发的玻璃基板材料ＰＤ２００和ＣＳ２５。     

晶须取向对SiCw／Al复合材料切削表面质量的影响

切削与晶须取向方向间的夹角对ＳｉＣｗ／Ａｌ复合材料切削表面质量有很大影响。当切削角为４５°时，晶须拔出和转动现象均较少，复合材料切削表面粗糙度最低。当切削角为１３５度时，晶段转动造成的撕裂破坏程度很大，复合材料切削表面粗糙度最大。