Further study on the cooling correction in bomb calorimetry: Theoretical aspects of approximate formulae

On the basis of the compensation of errors it is postulated that the most accurate correction may not always give the most accurate result for calorific value, and experimental evidence for this is presented. A new criterion is therefore suggested for judging the best (not necessarily the most accurate) cooling correction. Using this principle the cooling correction formula previously proposed is improved which results in higher accuracy whilst retaining the original simplicity.     

Motion and structure interpretation of an optical switch

This paper focuses on tracking, reconstruction and motion estimation of a well-defined MEMS optical switch from a microscopic view. For out-of-view reconstruction, a homography capable of transforming feature points and feature lines between a microscopic image and a CAD model of the switch is implemented. The homography between two sequential microscopic images is decomposed and factorized for motion estimation. Optical flow has also been explored to provide rough estimations of rotation centre and angle. The paper also illustrates motion parameter optimization principles to deal with uncertainty inherent in micro world. After non-linear optimization, estimation accuracy for rotation angle and rotation centre can reach 0.06° and pixel level, respectively.     

Amorphous diffusion bonding of steel pipe and its impact toughness

An iron-based amorphous foil (FeNiCrSiB) was used as an interlayer for the amorphous diffusion bonding of low carbon steel pipes under argon flux. The microstructure and mechanical properties of the joint were analyzed using an electron probe micro-analyzer (EPMA), tensile test, bending test and impact test. The results show that the joint microstructure resembles that of the base metal and no precipitates form at the joint. Melting point depressants (B, Si) diffuse far away from the joint and the base metal element is homogenous across the joint. The joint impact toughness is greater than the base metal toughness and the mechanical properties of the joint are similar around the pipe.     

Magnetic properties and thermal stability of CoFeNi-based amorphous films

CoNiFe-based amorphous films were magnetron-sputtered to investigate their structural and magnetic properties, including annealing-induced effects and interfacial influence from additional layers of Ta and Cu. The amorphous structure was confirmed by diffraction experiments. The magnetic measurements showed a well-defined uniaxial anisotropy in plane, arising possibly from atom oblique incidence effects competing with the stray field of the magnetron. The anisotropy could be influenced by using a Ta buffer layer, though the interfacial reaction gives rise to a dead layer. A coercive force H _c of 1–2 Oe and a magnetization of 680 emu/cm³ were measured at room temperature; properties which show promise for application in magnetotunneling junction devices. Thermal analyses showed a two-stage crystallization behavior, which started at 400°C and ended at about 600°C. The Curie temperature of the amorphous phase was estimated to be about 440°C.     

真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。     

Optimal diagonal precoder for multiantenna communication systems

In this paper, we examine a multiantenna single-user wireless communication system fitted with a QR-based successive cancellation receiver (QR receiver). Initially, our consideration is confined to uncoded binary phase shift keying (BPSK) signals transmitted through independent and identically distributed (IID) Rayleigh fading channels and to the design of an optimum precoder for the transmitter. For minimum feeding back of the channel state information (CSI) to the transmitter from the receiver, we stipulate the precoder to be in the form of a power loading square diagonal matrix. We proceed to develop the theory for the design of this diagonal matrix based on the minimization of the lower bound of the average bit error rate (BER) of transmission. The design obtained provides substantially lower error rates than most of other existing schemes under the same environment. The corresponding gain in signal-to-noise ratio (SNR) can be several decibels. To further improve the performance, we extend the design to include an optimal detection order of the received bits using an iterative approach. This iterative process proves to have fast convergence and results in a design providing significant SNR gain. We also propose a subchannel dropping scheme for cases in which SNR is low, and when the minimum BER precoder is equipped with this scheme, its average performance can be substantially superior to the Vertical Bell Laboratories Layered Space-Time (V-BLAST) detection. We extend our design of the optimum precoder to quadrature amplitude modulation (QAM) modulation scheme and similar performance gain has been observed.     

月桂醇聚氧乙烯醚硝酸酯助燃降污性能的研究

通过柴油发动机台架试验证明 ,月桂醇聚氧乙烯醚硝酸酯用作柴油添加剂 ,既可提高柴油的燃烧性能 ,又可降低排放尾气中的一氧化碳 (CO)、未燃碳氢化合物 (HC)、氮氧化物 (NOx)含量及烟度等多种功能 ,是一种良好的多功能柴油助燃消烟添加剂。     

高柔韧性尼龙1010材料的制备

对尼龙1010/NBR/增塑剂体系进行了系统研究,发现在挤出机中环氧扩链剂可以对尼龙进行扩链反应,且环氧树脂对尼龙1010的扩链反应活性较高,扩链效果比较明显;N-丁基苯磺酰胺是尼龙的良好增塑剂,经增塑、增韧后可以使经扩链后的尼龙1010柔韧性有明显提高.采用SEM和TEM对所制备的材料进行了形貌分析,发现用NBR增韧尼龙,对于不同的基体材料,橡胶粒子的形貌有很大不同,粒子由增韧纯尼龙的椭球形变为在增塑尼龙基体中不规则的形状.     

Studies on the microstructure of the black-glazed bowl sherds excavated from the Jian kiln site of ancient China

The Jian kiln, located in present-day Jianyang county of Fujian province, mainly produced black-glazed tea bowls. Jian tea bowl was used as a utensil for tea tasting and was greatly appreciated by emperor Huizong of the Northern Song dynasty. The black glaze of Jian bowl was sometimes marked with streaks or spots, usually called “hare's fur” or “oil spot”, which are the crystalline markings of iron oxide precipitated during firing in the dragon kiln. In this study, black-glazed Jian bowl sherds excavated from the late Northern Song strata of Luhuaping and Daluhoumen Jian kiln sites were adopted as test samples. Based on the physico-chemical foundation for the formation of glaze microstructure, the correlation among composition, microstructure, and visual appearance has been investigated by means of energy-dispersive X-ray fluorescence, X-ray diffraction, and field emission electron microscopy. For the first time, the study provides realizing proofs for two kinds of microstructural forming mechanics.