Effect of ethanol–gasoline blends on engine performance and exhaust emissions in different compression ratios

Renewable energy sources for the gasoline engines alcohols gain importance recently. These renewable energy sources have attracted the attention of researchers as alternative fuel due to their high octane number. In addition, these are also clean energy sources and can be obtained from the biomass alcohols with low carbon like ethanol. In this study, the effect of compression ratio on engine performance and exhaust emissions was examined at stoichiometric air/fuel ratio, full load and minimum advanced timing for the best torque MBT in a single cylinder, four stroke, with variable compression ratio and spark ignition engine.     

Effects of premixed diethyl ether (DEE) on combustion and exhaust emissions in a HCCI-DI diesel engine

In this study, the effects of premixed ratio of diethyl ether (DEE) on the combustion and exhaust emissions of a single-cylinder, HCCI-DI engine were investigated. The experiments were performed at the engine speed of 2200 rpm and 19 N m operating conditions. The amount of the premixed DEE was controlled by a programmable electronic control unit (ECU) and the DEE injection was conducted into the intake air charge using low pressure injector. The premixed fuel ratio (PFR) of DEE was changed from 0% to 40% and results were compared to neat diesel operation. The percentages of premixed fuel were calculated from the energy ratio of premixed DEE fuel to total energy rate of the fuels. The experimental results show that single stage ignition was found with the addition of premixed DEE fuel. Increasing and phasing in-cylinder pressure and heat release were observed in the premixed stage of the combustion. Lower diffusion combustion was also occurred. Cycle-to cycle variations were very small with diesel fuel and 10% DEE premixed fuel ratio. Audible knocking occurred with 40% DEE premixed fuel ratio. NO_x-soot trade-off characteristics were changed and improvements were found simultaneously. NO_x and soot emissions decreased up to 19.4% and 76.1%, respectively, while exhaust gas temperature decreased by 23.8%. On the other hand, CO and HC emissions increased.     

Tungsten(VI) oxide supported rhodium nanoparticles: Highly active catalysts in hydrogen generation from ammonia borane

Herein, we report the use of tungsten(VI) oxide (WO₃) as support for Rh⁰ nanoparticles. The resulting Rh⁰/WO₃ nanoparticles are highly active and stable catalysts in H₂ generation from the hydrolysis of ammonia borane (AB). We present the results of our investigation on the particle size distribution, catalytic activity and stability of Rh⁰/WO₃ catalysts with 0.5%, 1.0%, 2.0% wt. Rh loadings in the hydrolysis reaction. The results reveal that Rh⁰/WO₃ (0.5% wt. Rh) is very promising catalyst providing a turnover frequency of 749 min^?1 in releasing 3.0 equivalent H₂ per mole of AB from the hydrolysis at 25.0 °C. The high catalytic activity of Rh⁰/WO₃ catalyst is attributed to the reducible nature of support. The report covers the results of kinetics study as well as comparative investigation of activity, recyclability, and reusability of colloidal(0) nanoparticles and Rh⁰/WO₃ (0.5 % wt. Rh) catalyst in the hydrolysis reaction.     

LU triangularization extreme learning machine in EEG cognitive task classification

Neural Computing and Applications - Electroencephalography (EEG) has been used as a promising tool for investigation of brain activity during cognitive processes. The aim of this study is to reveal...     

Offsite Manufacturing in the Construction Industry for Productivity Improvement

Offsite manufacturing (OSM) is believed to be an alternative means of improving construction productivity. However, OSM has attracted limited attention from researchers and industry stakeholders, particularly in developing countries. Therefore, this study considers the key factors hindering the industry-wide adoption of OSM in the Cambodian context. A survey conducted with 75 construction practitioners asked respondents to quantify the level of influence from 30 constraints pertaining to OSM. Multi-attribute utility and correlation coefficient analyses were used to statistically analyze the data. Six broad categories of constraints to adopting OSM underlie the challenges facing the local industry: project planning and methodology, construction cost, construction industry and culture, skill and shortage, supply chain and logistics, and construction site operations. The findings may be useful for construction engineering professionals seeking ways to improve construction productivity performance by implementing OSM as an alternative technique in developing countries.     

Immobilization of glucoamylase on magnetic poly(styrene) particles

Magnetic poly(styrene) particles including active groups were prepared for enzyme immobilization without any activation process. Glucoamylase, which is widely used in industry, was immobilized onto these particles. The effects of pH, buffer concentration, and temperature on immobilization were investigated; moreover, the effect of immobilization temperature on immobilized glucoamylase activity was determined for the hydrolysis of maltose. The acetate buffer with the concentration of 6 × 10⁻⁴ M at pH 4 and 20–30°C was found as the most suitable medium for the immobilization of the glucoamylase. The amount of bound protein is 8 mg/g particle with the immobilization yield of 70%. The maximum activity obtained with immobilized glucoamylase is approximately 70% of the free one. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 69–73, 1999     

微生物对混凝土的侵蚀

微生物侵蚀会导致混凝土的严重破坏,尤其导致了城市污水收集和处理系统的过早破坏,使其需要提前修复。世界范围内的研究结果表明:处于污水和下水道污泥中的混凝土会遭受由硫酸盐、酸、CO2等导致的严重破坏。评述了混凝土处于利于细菌生长和生物降解环境中时的细菌、微生物侵蚀破坏过程。此外还分析了硫酸产生的机理(硫循环)、用于污水管道系统和农用工业的混凝土的受侵蚀破坏机理以及评价混凝土抵抗微生物侵蚀的方法。     

Effect of Nitric Acid “Washing” Procedure on Electrochemical Behavior of Carbon Nanotubes and Glassy Carbon μ-Particles

The electroanalytic performances of glassy carbon paste electrode (GCPE), multi-walled carbon nanotube (MWCNT)-GCPE and double-walled carbon nanotube (DWCNT)-GCPE, which include HNO₃ washed/unwashed materials, were compared by monitoring cyclic voltammograms of potassium ferricyanide and catechol. Electrodes were prepared by introducing proper amount of DWCNT and MWCNT into GCPE. First untreated materials (DWCNT, MWCNT, GC μ-particles) were used in the electrodes and then HNO₃-treated materials were utilized for comparing difference in electrochemical performances. The effect of treatment procedure was also examined by applying Raman spectroscopy to treated and untreated materials. Moreover, TEM images were obtained for further investigation of MWCNT and DWCNT.