非金属电镀用导电漆的研制

介绍了导电漆、作为导电填料的片状镀银铜粉的制备工艺流程。分别研究了漆膜表面单位电阻与镀银铜粉的含量及其粒径以及钛酸酯偶联剂的含量之间的关系。结果表明,当镀银铜粉的粒径为400目、质量分数在57%~65%之间,钛酸酯偶联剂的质量分数为10%时,所得涂膜的导电性能最佳。加入含C-18的油酸可以使导电漆长期贮存而电阻值不变。经检测,所得涂膜具有良好的性能:附着力1级,硬度1 H,柔韧性1 mm,冲击强度50 kg/cm2,膜厚10~15μm,漆膜表面每厘米电阻0.15Ω,每分米电阻0.47Ω。指出了导电漆应用过程中的注意事项。     

环氧SBS开环制备顺酐化离聚体及其物化性能的研究

利用环氧化苯乙烯-丁二烯-苯乙烯嵌段共聚物（ESBS）的环氧基与顺丁烯二酸氢钾（HKM）在相转移催化剂和开环催化剂存在的条件下开环反应制得钾离聚体。研究了其反应条件，由于添加了助剂BM，环氧基开环率达到了95．2％，并用FTIR确定了离聚体的生成；通过对不同环氧值ESBS开环反应，研究了不同离子基团质量摩尔浓度对离聚体物化性能的影响。     

MODEL FOR PREDICTING THE LATERAL DISPERSION COEFFICIENT OF SOLIDS IN GAS-SOLIDS FLUIDIZED BEDS

The lateral mixing of solids in a gas-solids fluidized bed is very complicated.It can be caused by:(a)bubble movement through the bed,(b)bubble burst at the bed surface,and(c)gross particle circulation in thebed.However,experiments show that the major factors effected the lateral mixing of solids are the bubblemovement through the bed and the bubble burst at the bed surface.Thus a model with two mixing re-gions,i.e.mixing in bubble rising region and mixing in bubble breaking region,was proposed.Based on thismodel,an equation for predicting the lateral dispersion coefficient of solids in gas-solids fluidized beds wasderived without any adjustable parameter.The calculated values by this equation are well comparable withthe observed data including the present work and the other investigations.     

Possible Energy Network with polygeneration system and CCS for China

On basis of adopting polygeneration systems for power and alternative fuels,capturing CO2 with near zero energy penalties,and storing CO2 on sites,a new kind of Energy Network can integrate energy utilization,CO2 capture,transportation and storage synthetically.Techno-economic analysis of this solution focusing on Inner Mongolia and the Yangtze River Delta districts had been carried with comparison to the chain method for energy utilization and CO2 sequestration.This solution can save 21.5% of energy,and re...     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...     

A novel shaft-less double suction mini pump

A novel double suction shaft-less mini pump was developed for heat control of small energy systems in this study.The mini pump impeller with an exit diameter of 40 mm was combined with the motor rotor supported by the hybrid dynamic bearing.The specific speed of the pump was 125 min-1 m3 min-1 m.The hydraulic performance of the pump was investigated experimen-tally under four rotational speeds.From the test results,it was recognized that the pump could provide a flow discharge of 5 L/min and head of 1.5 m,w...     

一种基于优先级的Ad hoc网络QoS模型*

提出一种基于优先级业务分类的Ad hoc网络QoS模型,它能够为多种优先级多种类别的业务提供不同等级的服务。源端判断业务是否允许接入,中间节点只负责转发允许接入的业务。在资源不足的情况下,能为最高优先级业务提供相对稳定的带宽资源,高优先级业务能获得比低优先级业务更高的调度权限。通过OPNET下的仿真,证明该模型能满足不同级别QoS的要求。     

气压驱动式自动离合器控制技术研究

为了以较低成本实现AMT系统中离合器执行机构的气压驱动,在对离合器控制过程深入分析的基础上结合气动控制特点,提出了通过高速开关电磁阀以PWM方式驱动纯气动离合器执行机构的方法,及离合器参考模型自适应控制方法.通过多位驾驶员在不同道路条件和环境条件下的实车道路考核,验证了这种控制方法的可行性,研究结果同时表明:采用该方法的离合器执行机构价格低廉,为进一步实现产业化奠定了基础.     

韧性断裂准则在板料成形中应用研究进展

对板料成形中的成形极限应力图、最大变薄率、成形极限图以及韧性断裂准则等预测成形极限的方法进行了综述和分析,提出了利用韧性断裂准则能够较好地预测塑性差的板料成形极限,而且还能考虑应变路径的变化.利用有限元方法模拟时,韧性断裂准则既可以运用到完全耦合的弹塑性损伤模型的增量方法中,也可以运用到一步有限元逆算法中.指出了为准确地预测成形极限,除了提高有限元模拟精度外,应找到一种本质地反映材料性能的准则.     

基于SVM的汉语句子片段划分

针对长句子引起句法分析性能下降的问题,本文提出了一种基于SVM的句子片段划分方法:先根据语法结构将句子划分为多个片段,识别出每个片段的类别;然后根据片段的类别将句子分割为几个部分,每个部分作为句法分析的基本单元;最后将句法分析之后的各个部分进行合并,形成完整的分析结果.该方法减小了句法分析的复杂度,提高了分析的准确率.