薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

不同粒度松散煤体的氧扩散特性实验研究

以自行研制的煤对氧扩散特性测试装置为实验手段,在常温环境条件下测试了不同粒度松散煤体对氧的自由扩散特性.实验结果表明:煤样粒度的变化对取气腔氧浓度流出曲线的影响表现出2个极限值,煤样粒度在20～100目之间时,取气腔氧气浓度梯度随煤样粒度的增大而增大;当煤样粒度<20目或>100目时,煤样粒度的再变化对氧浓度流出曲线的影响则微乎其微;取气腔氧浓度曲线流形基本符合指数曲线的变化规律.     

合成2,4-二叔丁基苯酚工业试验

以离子交换树脂为催化剂，苯酚和甲基叔丁基醚为原料合成2，4-二叔丁基苯酚(简称2，4酚)，合成产物经过滤再经间歇真空精馏精制提纯，得到高纯度的2，4酚成品。成品精馏后釜中残液在酸性白土催化剂的作用下通过歧化反应生成对叔丁基苯酚，再经精馏提纯得到成品对叔丁基苯酚。通过工艺优化，使2，4酚、对叔丁基苯酚形成联产生产工艺，降低了生产原料消耗和成本。     

An alternative method to compute the component fractions in the geometrical optical model: visual computing method

A method called visual computing was used to solve angular four-components' proportions and directional vegetation cover fraction for discrete canopies and continuous row-planted plants. It proved effective to predict the angular characteristics on pixel scale. The method could be an alternative way to a classical solution of geometrical optical models. A visual computing method would be effective especially when the canopies' spatial distribution and shapes were irregular and could not be described statistically.     

光学薄膜在光通信中的应用

主要介绍了光学薄膜在光通信的无源型器件中的原理及应用,并与光纤光栅和平面光波导型的无源器件作简单比较。     

EPON媒体接入控制的关键技术研究

文章简要介绍了基于以及太网的无源光网络（EPON）这种新型的接入网技术，将其与基于ATM技术的无源光网络（APON）的优缺点进行了比较，并对其媒体接入控制（MAC）的关键技术测距及上行接入进行了讨论，初步提出了光网络单元（ONU）的软、硬件实现方案。     

一种嵌入式TCP／IP的实现

针对许多小型嵌入式系统要求结构紧凑、开销小的TCP／IP协议栈的需求，提出一种可移植的非路由器TCP／IP原型的实现。该TCP／IP原型基于某种小型嵌入式系统，依据RFC1122兼容性规定，提供IP、ARP、TCP、UDP服务和Berkeley Socket编程接口。该实现代码短小，开销低，性能能够满足多数应用需求，具有较强的可移植性。     

脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。