A 640 by 480 Pixels Readout Circuit for IR Imaging

A readout circuit for a 640 × 480 pixels FPA (focal plane array) has been successfully designed, fabricated and tested. The circuit solution is based on a per pixel source-follower direct injection (SFDI) pre-amplifier. Signal multiplexing is performed in both X and Y direction. The pixel size is 25 m × 25m. The chip is optimized for a QWIP (quantum well infrared photodetector) operating at a temperature of 70 K. The circuit has been realized in a standard 0.8 m CMOS process.     

Shear elastic modulus estimation from indentation and SDUV on gelatin phantoms

Tissue mechanical properties such as elasticity are linked to tissue pathology state. Several groups have proposed shear wave propagation speed to quantify tissue mechanical properties. It is well known that biological tissues are viscoelastic materials; therefore, velocity dispersion resulting from material viscoelasticity is expected. A method called shearwave dispersion ultrasound vibrometry (SDUV) can be used to quantify tissue viscoelasticity by measuring dispersion of shear wave propagation speed. However, there is not a gold standard method for validation. In this study, we present an independent validation method of shear elastic modulus estimation by SDUV in three gelatin phantoms of differing stiffness. In addition, the indentation measurements are compared to estimates of elasticity derived from shear wave group velocities. The shear elastic moduli from indentation were 1.16, 3.40, and 5.6 kPa for a 7%, 10%, and 15% gelatin phantom, respectively. SDUV measurements were 1.61, 3.57, and 5.37 kPa for the gelatin phantoms, respectively. Shear elastic moduli derived from shear wave group velocities were 1.78, 5.2, and 7.18 kPa for the gelatin phantoms, respectively. The shear elastic modulus estimated from the SDUV, matched the elastic modulus measured by indentation. On the other hand, shear elastic modulus estimated by group velocity did not agree with indentation test estimations. These results suggest that shear elastic modulus estimation by group velocity will be bias when the medium being investigated is dispersive. Therefore, a rheological model should be used in order to estimate mechanical properties of viscoelastic materials.     

Comb-Push Ultrasound Shear Elastography (CUSE): A Novel Method for Two-Dimensional Shear Elasticity Imaging of Soft Tissues

Fast and accurate tissue elasticity imaging is essential in studying dynamic tissue mechanical properties. Various ultrasound shear elasticity imaging techniques have been developed in the last two decades. However, to reconstruct a full field-of-view 2-D shear elasticity map, multiple data acquisitions are typically required. In this paper, a novel shear elasticity imaging technique, comb-push ultrasound shear elastography (CUSE), is introduced in which only one rapid data acquisition (less than 35 ms) is needed to reconstruct a full field-of-view 2-D shear wave speed map (40 × 38 mm). Multiple unfocused ultrasound beams arranged in a comb pattern (comb-push) are used to generate shear waves. A directional filter is then applied upon the shear wave field to extract the left-to-right (LR) and right-to-left (RL) propagating shear waves. Local shear wave speed is recovered using a time-of-flight method based on both LR and RL waves. Finally, a 2-D shear wave speed map is reconstructed by combining the LR and RL speed maps. Smooth and accurate shear wave speed maps are reconstructed using the proposed CUSE method in two calibrated homogeneous phantoms with different moduli. Inclusion phantom experiments demonstrate that CUSE is capable of providing good contrast (contrast-to-noise ratio ≥ 25 dB) between the inclusion and background without artifacts and is insensitive to inclusion positions. Safety measurements demonstrate that all regulated parameters of the ultrasound output level used in CUSE sequence are well below the FDA limits for diagnostic ultrasound.     

Surface and interfacial fourier transform infrared spectroscopic studies of latexes. XIV. Surface phase separation in polystyrene/poly-n-butyl acrylate latex films

This study focuses on the behavior of sodium dioctylsulfosuccinate (SDOSS) in 50/50 w/w % polystyrene/poly(butyl acrylate) (p-Sty/p-BA) latex films. Specifically, mobility and orientation are examined in the context of the film formation by the use of dynamic mechanical thermal analysis and attenuated total reflectance (ATR) Fourier transform infrared (FT-IR) spectroscopy. While for the homopolymer blends of p-Sty and p-BA, two T_g values resulting from a phase separation of p-Sty and p-BA phases are observed, only a single T_g is detected for a copolymer of the same mixture, indicating a single phase within the film. ATR FTIR spectroscopic data indicate that the phase separation of p-Sty and p-BA blends does not occur uniformly across the film. After coalescence, p-Sty particles produce a significant degree of stratification at approximately 1.6 μm from the film surface. At this depth, the polystyrene rings assume preferentially parallel orientation to the film surface. At the same time, the hydrophilic groups of SDOSS surfactant (SO⁻₃Na⁺) are oriented preferentiallyparallel to the surface. Under high relative humidity conditions, water is able to diffuse into the film and swells the surface layers, thus causing them to expand. As a result, the top, predominately poly-n-BA surface becomes “thicker», and p-Sty phase appears to be near 2.3 μm from the surface. The polystyrene rings maintain their preferential parallel orientation to the surface, but the hydrophilic groups of SDOSS are able to diffuse into the film with the water uptake and are thus not present at the filmair interface. © 1996 John Wiley & Sons, Inc.     

Rotor dynamics of a sliding vane turbineRotor dynamik von turbinen mit gleitenden turbinenblaettern

A general mechanical design and performance analysis is presented for a sliding vane turbine. The analysis is general in the sense that it is valid for any stator profile and that there is no restriction on the turbine use. This analysis includes a dynamic force analysis on the vane, rotor dynamics, and vane kinematics. As an example, an eliptical stator sliding vane turbine is considered for the purpose of illustrating the procedure of applying the general analysis and presenting results by graphs as a function of significant design parameters.     

Novel phthalocyanine/polyol high-solids coatings: Structure—property relationships

A convenient synthetic procedure for preparing nickel carboxylated phthalocyanine is reported. Upon further hydroxylation, such metal phthalocyanine moieties are incorporated into several melamine-based polyester high-solids systems and the structure—property correlations are examined. Molecular level spectroscopic FTIR analysis and mechanical testing are correlated in an effort to establish structure—property relations in these coatings. It is found that the presence of metal phthalocyanine macrocycle as a cross-linking agent enhances such properties as adhesion, hardness, and impact resistance. © 1993 John Wiley & Sons, Inc.     

浅议村镇宏观布局模式

村镇体系在理论上为区域中心镇、一般乡镇、中心村、基层村的等级结构形式,其空间布局以点轴模式、中心地模式和散点模式最为常见。村庄的完善发展应是村庄合并。     

高效旋风分离器轴向速度和径向速度的计算

在赵伟中采用凯尔文定理推出的轴向速度和径向速度计算方法的基础上,引入下降流量的概念,推出了新的计算方法。该计算方法不仅在理论上优于原计算方法,而且与实测结果也符合较好。