Thermal transport and chemical conversion in single reacting sorbent particles

The effects of particle size and carbon dioxide concentration on chemical conversion in engineered spherical particles undergoing calcium oxide looping are investigated. Particles are thermochemically cycled in a furnace under different carbon dioxide concentrations. Changes in composition due to chemical reactions are measured using thermogravimetric analysis. Gas composition at the furnace exit is evaluated with mass spectroscopy. A numerical model of thermal transport phenomena developed previously is adapted to match the physical system investigated in the present study. The model is used to elucidate effects of reacting medium characteristics on particle temperature and reaction extent. Experimental and numerical results show that (1) an increase in particle size results in a decrease in carbonation extent, and (2) the carbonation step consists of fast and slow reaction regimes. The reaction rates in the fast and slow carbonation regimes increase with increasing carbon dioxide concentration. The effect of carbon dioxide concentration and the distinction between the fast and slow regimes become more pronounced with increasing particle size.     

分光光度法测定PVB中微量氯含量

建立了PVB树脂中氯含量的测定方法.采用添加混合试剂高温灰化,沸水浸取,分光光度法测定PVB树脂样品中的氯含量.该方法具有良好的精密度和准确度,分析成本低.     

Characterizations of friction welding joint interface for AISI 316

Because of heat amount is different from peripheral to central of friction welding interface, which is leaded to vary the characterizations along that interface. Current study, respectively, focused on the effect of different friction pressure on micro-structural and mechanical properties of that friction welding joint interface. Presently, these friction pressures are 110, 130, 150 and 170 MPa while kept all other conditions constant. The effects of different friction pressure on welding interface characterization were investigated by EDX, SEM, tensile, compression, impact and hardness tests. The tensile tests carried out on the standardized test piece with diameter 6 mm and 8 mm, thus, compression tests were extracted from the positions of 0°, 45° 90° with test specimen of 4 mm diameter and 6.5 mm length at weld center. Whereas, the impact test pieces were picked up in two positions, the first one is symmetrical, which it obtained to the respect of the rotation axis and the interface, on the other hand, the second one is non-symmetrical with the axis of rotation and symmetrical to the interface, for making the notch head coincide with the center of the welded joint, The obtained results showed that with reducing of friction pressure will present lack of bonding increasing from peripheral toward the welding center, which will responsible on reducing of the mechanical properties such as tensile, compression and impact strength.     

床温及SNCR脱硝对CFB锅炉NOx和N2O排放影响的试验研究

为了研究循环流化床（CFB）锅炉燃用无烟煤时床温及选择性非催化还原（SNCR）脱硝对于NO和N2O排放的影响，在1 MW CFB试验装置上开展了试验研究。结果表明:床温由880 ℃提高到970 ℃，NO排放质量浓度由119.5 mg/m3上升到226.0 mg/m3，N2O排放质量浓度由216.0 mg/m3降低到102.2 mg/m3；在氨氮摩尔比（NSR）为0~3.7之间，随着NSR的提高，脱硝效率从0上升到50.72%；进一步提高NSR到5.2，脱硝效率升至53.61%，增加较为缓慢；随着NSR从0提高到1.7，N2O排放质量浓度由84.3 mg/m3上升至118.3 mg/m3，增长较为缓慢；进一步提高NSR至2.0，N2O排放质量浓度上升至187.7 mg/m3，增长速度提高；继续提高NSR至5.2，N2O排放质量浓度上升至381.4 mg/m3；CFB锅炉采用以尿素为还原剂的SNCR脱硝工艺时，单纯通过加大NSR来提高脱硝效率不仅效果有限，过量喷入的还原剂会造成N2O排放量的显著提高。     

蛋类礼盒包装结构的缓冲性能研究

目的研究蛋类礼盒包装结构的缓冲性能。方法以蛋类尺寸为基础,建立可发性聚乙烯(expandable polyethylene. EPE)缓冲单元结构和组合结构,进行静态仿真分析和实验验证,比较结构在形状、叠合层数、组合形式等参数变化时的载荷与位移。结果结构层数变化相同时,单元结构的极限载荷从143N增加到236 N,组合结构的极限载荷从224 N增加到476 N,均呈近线性增长。结论蛋类礼盒包装中,组合结构的承载能力优于单元结构,通过单元结构的组合,可满足不同蛋类的包装要求。     

Passive micromixer with baffles distributed on both sides of microchannels based on the Koch fractal principle

Since the beginning of the 21st Century, the development of microfluidic chip technology has been very rapid and has attracted the attention of more and more scholars. As an important part of the microfluidic chip, the performance of the micromixer is critical. The fractal structure in the microchannels helps to improve the mixing performance of the micromixer and improve the mixing efficiency of the micromixer. The research results of other scholars are of great significance to the research of the present paper, which mainly studies the effect of changing the baffle state on the mixing efficiency of the micromixer based on the Koch fractal principle. Through simulation analysis, it was found that the mixing efficiency of the baffles distributed on both sides of the microchannel was higher than the mixing efficiency of the baffles distributed on the microchannel side. When the distance between adjacent baffles was divided into 0.15, 0.25 and 0.35 mm, simulated data suggested that the baffle distance of 0.15 mm was best. Increasing the number of baffles from six to eight groups increased the mixing path of the fluid in the microchannel and improved mixing efficiency. A comparison of mixing efficiencies of the 0°, 15° and 30° baffle angles revealed that very significant improvement in mixing efficiency was obtained at 30°. © 2019 Society of Chemical Industry     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

喷油方式对斜齿轮齿面温度的影响

为探讨喷油方式对齿面温度的影响，以斜齿轮为研究对象，通过CFD仿真和试验研究不同喷油方式对斜齿轮齿面温度的影响。针对斜齿轮喷油润滑过程的特点，分析其齿面摩擦生热量，简化轮齿喷油润滑计算模型，并基于CFX进行齿面对流换热仿真研究，得到了不同喷油方式下的齿面温度；基于功率开放式斜齿轮试验平台，对不同喷油方式下的齿面温度进行了试验测量，与仿真计算结果进行对比分析。结果表明：在高速重载斜齿轮传动系统中，啮出侧喷油润滑的方式比啮入侧喷油润滑方式的冷却降温效果要好。