Evaluation of accuracy of measuring intraocular pressure by handheld non-contact applanation tonometer

PURPOSE: To evaluate the accuracy of measuring intraocular pressure by handheld non-contact applanation tonometer. METHOD: 58 patients' (113 eyes) intraocular pressure were measured by Keeler, non-contact tonometer and R 900 Goldmann applanation tonometer and the results of measurement of intraocular pressure by the two kinds of tonometers were compared. RESULT: The mean intraocular pressure measured by non-contact is 16.31 +/- 5.59 mmHg and 17.49 +/- 6.13 mmHg (1 mmHg = 0.1333 kPa) by Goldmann applanation tonometer, respectively. There was no statistical significance to be found (P > 0.05) between the two methods. By linear correlation and regression analysis, a positive correlation was found between the two methods (r = 0.8942, b = 0.8154). CONCLUSION: The handheld non-contact tonometer has the same accuracy and reliability of measurement of intraocular pressure comparing with Goldmann applanation tonometer, and it can be used in glaucoma clinic and screening.     

锆(Ⅳ)-3,5-diBr-PADAP-安替比林三元配合物的分光光度研究与应用

本文提出在安替比林存在下,以3,5-diBr-PADAP为显色剂,分光光度测定微量锆的新方法。在pH1～2的HCl介质中,锆(W)与试剂和安替比林形成配合比为1:1:1的红色三元配合物,最大吸收值在615nm波长处,摩尔吸光系数ε=1.35×10~5。锆(Ⅳ)量在0～25μg/25ml范围内,遵守比尔定律。方法简单、快速、准确。若采用钽试剂—苯萃取法分离共存离子,可适用于钽铌矿和合金中痕量锆的测定。     

一种新型背面接触式H~+-ISFET

简要地介绍了氢离子敏场效应晶体管(H~+-ISFET)的基本结构和工作原理,提出了一种新型背面接触式H~+-ISFET。对该结构在版图、工艺设计中的有关问题,进行了探讨。最后指出:它在pH值的测量中有较好的实用价值。     

Effect of Stress State on Growth of Interfacial Intermetallic Compounds Between Sn-Ag-Cu Solder and Cu Substrates Coated with Electroless Ni Immersion Au

Excessive intermetallic compound (IMC) growth in solder joints will significantly decrease the reliability of the joints. IMC growth is known to be influenced by numerous factors during the component fabrication process and in service. It is reported that, other than temperature and holding time, stress can also influence the IMC growth behavior. However, no existing method can be used to study the effect of stress state on IMC growth in a controlled manner. This paper presents a novel method to study the effect of stress on interfacial IMC growth between Sn-Ag-Cu solder and a Cu substrate coated with electroless Ni immersion Au (ENIG). A C-ring was used and in-plane bending induced tensile and compressive stresses were applied by tightening the C-ring. Results revealed that in-plane compressive stress led to faster IMC growth as compared with in-plane tensile stress.     

非水解溶胶-凝胶法低温合成硅酸锆

以工业纯ZrCl4、 Si(OC2H5)4为前驱体,通过非水解溶胶-凝胶法合成了硅酸锆.采用DTA-TG和XRD等测试手段研究了凝胶热处理过程中的物相变化.结果表明:当前驱体溶胶中未引入矿化剂时,硅酸锆的合成温度高达1450℃;相比之下,溶胶中引入矿化剂LiF后在600℃下便开始出现了ZrSiO4衍射峰,在700℃合成的硅酸锆不仅合成率高,而且晶体发育好,实现了低温合成硅酸锆的目标.     

Material removal and surface damage in EDM of Ti3SiC2 ceramic

Material removal and surface damage of Ti₃SiC₂ ceramic during electrical discharge machining (EDM) were investigated. Melting and decomposition were found to be the main material removal mechanisms during the machining process. Material removal rate was enhanced acceleratively with increasing discharge current, i_e, working voltage, u_i, but increased deceleratively with pulse duration, t_e. Microcracks in the surface and loose grains in the subsurface resulted from thermal shock were confirmed, and the surface damage in Ti₃SiC₂ ceramic led to a degradation of both strength and reliability.     

Effect of fluoropolymer antidripping agent on the microstructure and properties of polyesters

Poly(ethylene terephthalate) (PET) is of excellent mechanical properties and melt processability and is widely used as raw material for textile fibers. However, the flame retardant properties of PET were rather poor, and both reactive and additive phosphorus- and halogen-containing compounds have been employed to enhance the reaction-to-fire properties while the meltdripping behaviour during burning hasn’t been handled properly with the flame retardants. In this work, fluoropolymer was blended with both pure PET (pPET) and reactive phosphorus-containing flame retarded copolyester (fPET), and the flame retardance and char formation and mechanical properties of the resulted pPET and fPET blends were investigated. The tensile strengths of modified pPET samples were worsen whereas those of modified fPET samples were improved at low concentrations. The initial thermal degradation in nitrogen was accelerated remarkably for the two polyesters with fluoropolymer. The oxygen indices of the all modified samples were reduced while char formation and meltdripping suppression were encouraged. The apparent melt viscosity and elasticity for the two polyesters were gained much with antidripping agent. Therefore, fluoropolymer improved char formation of the two polyesters based on the gaseous phase mechanism while the partial suppression of meltdripping behavior and the decrease of mechanical properties mainly originated from the increase of melt viscosity via fibrillation for pPET.     

Evolving Fault-Tolerant Neural Networks

In this paper, genetic algorithm is used to help improve the tolerance of feedforward neural networks against an open fault. The proposed method does not explicitly add any redundancy to the network, nor does it modify the training algorithm. Experiments show that it may profit the fault tolerance as well as the generalisation ability of neural networks.     

Validation and modification of WAVE spray model for diesel combustion simulation

In CFD simulation of diesel combustion, the predictive capabilities of the spray model play the most important role. Consequently, under the strict guidelines of the V&V, a method to adjust parameters of diesel spray model WAVE to accompany with the in-cylinder physical progress has been investigated in this paper. Moreover, the simulation of the spray has been validated by high-speed photography experiments and verified by the equation proposed by Hiroyasu. Finally, a modified setup for the WAVE spray model has been proposed and applied in the spray and combustion simulation for Deutz1013 diesel in different engine speed.     

Viscoelastic properties of polyarylene ether nitriles/thermotropic liquid crystalline polymer blend

Polyarylene ether nitriles (PEN)/thermotropic liquid crystalline polymer (TLCP) blend was prepared via melt mixing. The immiscible phase morphologies, linear and nonlinear, as well as transient viscoelastic properties of the blend were studied using SEM, rheometer, and DMA. The linear dynamic viscoelastic behavior of the blend shows temperature dependence due to further evolution of the immiscible morphology and, as a result, the principle of time‐temperature superposition (TTS) is invalid. In the steady shear flow, the discrete TLCP phase is difficult to be broken up because of the high viscosity ratio of the blend systems, while is easy to be coarsened and followed by elongation, and finally, to form fibrous morphology at high TLCP content and high shear level. During this morphological evolution process, the transient stress response presents step increase and nonzero residual relaxation behavior, leading to increase of the dynamic viscoelastic responses after steady preshear. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008