Effect of Heat Treatment on Microstructure and Mechanical Properties of Extruded PM Ti–6Al–4V Alloy With Deformation Flowlines

Metallurgical and Materials Transactions A - Two heat treatments, namely 955°C/2h/AC (AC = air cooling) and 955°C/4h/FC (FC = furnace cooling), were carried out on...     

Effect and Evolution of Oxide Film in the HDH-Ti Powder Surface on Densification Behavior During Sintering

Metallurgical and Materials Transactions A - In this work, we used hydride-dehydride Ti (HDH-Ti) powders (with the oxygen levels of 0.17 and 0.51 wt pct, respectively) combined with microstructural...     

Development of ultra-narrow gap welding with constrained arc by flux band

0 IntroductionThe merits of narrow gap welding (NGW) such ashigh productivity and quantity, minimal distortion, highcost-effectiveness, and all position capability are wellknown. The narrower the gap, the more significant the a-bove merits. Moreover, while an ultra-narrowgap welding(UNGW) process with less than 5 mm gap width is used,its some advantages are very useful for preventing thestress corrosion crack in austenitic steel piping, and forwelding some update steels. For example, in aus…     

工业控制中实时数据传递新技术

采用面向对象机制，论述了Ｗｉｎｄｏｗｓ环境下动态数据传递的基本原理，介绍了主要动态数据交换事务以及在工业控制中动态数据传递的流程。并采用ＢｏｒｌａｎｄＣ＋＋语言给出了工业控制中动态数据传递的基本实现     

Defining Specifications for Custom Products: A Multi-Attribute Negotiation Approach

Defining product specifications so that customers' needs could be well matched with suppliers' capabilities is a very challenging task in custom product design. This research links technical requirements on product design with product management issues and formulates specification definition as multi-attribute negotiation. Specification negotiation is modeled as an iterative process of give and take in search of a mutually acceptable configuration. A negotiation support system is developed based on a product configuration system to identify among the multiple attributes what to give, what to take, and by how much so as to facilitate specification negotiation operationally.     

含硫氰酸盐、硫化物固体废物中总氰化合物测定方法

实验建立了含硫氰酸盐、硫化物固体废物中总氰化合物的测定方法,采用硝酸银滴定法、异烟酸-吡唑啉酮分光光度法分别测定总氰化合物含量高、低的样品。通过条件实验优化了前处理方式、称样量和干扰去除方法。该方法测定结果的相对标准偏差为0.43%～1.33%,加入标准物质回收率为91.5%～101.5%,精密度和准确度良好,符合测定要求。     

方管两侧同时冲孔模设计

通过对零件的工艺分析，改进了工艺方案，用一副对冲孔模完成两边同时冲孔，降低了生产成本，提高了生产效率；并介绍了该对冲孔模具的结构特点、设计思路、应注意的问题和装配工艺性。     

An electrochemical method for the preparation of Mg–Li alloys at low temperature molten salt system

Mg–Li alloys have been prepared by electrolysis in a molten salt electrolyte of 50% LiCl–50% KCl (mass%) at low temperature of 420–510 °C. The effects of electrolytic temperature and cathodic current density on alloy formation rate and current efficiency were studied. For the deposition of metallic lithium on the cathode consisting of solid Mg and liquid Mg–Li, both electrolytic temperature and cathodic current density have no obvious influence on current efficiency; while for the deposition of metallic lithium on the solid magnesium cathode, both electrolytic temperature and cathodic current density greatly affect alloy formation rate and current efficiency. The optimum electrolysis condition is—molten salt mixture, LiCl:KCl = 1:1 (mass%), electrolytic temperature: 480 °C, cathode current density: 1.13 A cm⁻². Mg–Li alloys with low lithium content (about 25 wt% Li) were prepared via electrolysis at low temperature following by thermal treatment at higher temperature.     

17-4PH沉淀硬化不锈钢氮离子注入及其复合改性的研究

采用N+注入，N-C-O共渗结合N+注入的表面复合改性方法，探索强化17－4PH钢表面的有效途径，该方法赋予基体表面一定深度的改性范围与低摩擦系数，因而强化效果达到最佳。同时还探索了不同时效温度下，基体心部硬度变化的规律。     

强流脉冲离子束表面再制造技术原理与应用

采用TEMP-6型强流脉冲离子束(HIPIB)装置开展了HIPIB表面再制造技术的研发.HIPIB装置主体由高压脉冲电源系统和高功率离子二极管系统组成,通过高压短脉冲在二极管中放电产生阳极等离子体并引出ns级强流离子束.HIPIB辐照材料表面,发生显著的熔融、蒸发和剧烈烧蚀,物质喷射的反冲作用在辐照表面形成由表及里的应力波,导致材料表层强烈的热-力学效应.利用HIPIB与材料表面的相互作用,应用于涡轮叶片表面的清洗维修,可有效去除涡轮叶片基体因高温氧化形成的氧化物,伴随表层的重熔将叶片基体表面微观缺陷焊合,获得了光滑、平整的涡轮叶片修复表面.实现了HIPIB辐照在涡轮叶片表面再制造方面的应用.