A compact LTCC branch-line coupler UsingModified-T equivalent-circuit modelfor transmission line

In this letter, a compact branch-line coupler is proposed by making good use of the three-dimensional layout capability of the low-temperature co-fired ceramic (LTCC) substrate. This branch-line coupler is accomplished by using lumped-inductors and lumped-capacitors to realize the modified-T equivalent-circuit model for the transmission line so that the circuit size may drastically be reduced. Specifically, a very compact LTCC branch-line coupler with a size of 0.079/spl lambda//spl times/0.0717/spl lambda/ is implemented and carefully examined, where /spl lambda/ is the wavelength of the multilayer structure at the operating frequency f/sub 0/.     

PBA/PMMA核壳结构乳胶粒子粒径分析

采用种子乳液聚合制备出了PBA/PMMA核壳结构乳胶粒子，研究并分析了MMA在3种不同投料方式（间歇法、半间歇法和平衡溶胀法）下粒子粒径变化情况。实验发现第二单体采用间歇法投料可获得较理想的核壳结构乳胶粒。     

SF6气体绝缘电容式电压互感器研制

本文介绍西容公司新研制的一种完全无油化的SF6气体绝缘电容式电压互感器,提出了关键技术问题解决方案和产品绝缘结构的设计思路.并介绍了研制成功的110kV和220kV系列产品的结构、技术参数、性能指标、试验考核情况和产品特点.     

A push mechanism for GPRS supporting private IP addresses

The General Packet Radio Service (GPRS) provides a packet switched data service for mobile users. However, the existing GPRS specification does not provide the push mechanism and it is difficult to support GPRS services such as call termination (incoming call) for wireless voice over IP (VoIP). Based on the short message service, this paper proposes a push mechanism for GPRS supporting private IP addresses. Our approach does not need to modify the existing GPRS structure.     

Enhancement of underfill capillary flow in flip-chip packaging by means of the inertia effect

This paper describes how the use of inertia forces induced by the rotation of a working disk may be adopted to increase the fill rate of the flip-chip packaging process and thereby reduce the process cycle time. It is shown how the driving forces resulting from the inertia effect are determined by the Weber number. The constant and varying contact angle models are compared under a specified set of process conditions. The calculated flow behavior results indicate that the relationship between the contact angle, the average fluid velocity, the liquid-air interface position, and the filling time depends upon the Weber number. The constant and varying contact angle models are utilized in the analysis of a new processing method referred to as rotation-enhanced underfill packaging (REUP). The inertia effect induced by the angular motion of the working disk is shown to enhance the flow of the underfill encapsulant and to reduce the time of the underfill process. The present results confirm that the rotation of the working disk leads to an increased underfill capillary flow rate, which is beneficial in reducing the production cycle time of the flip-chip packaging process.     

梯恩梯-吉纳、地恩梯-太安装药体系自旋爆轰特性的研究

本文研究了梯恩梯-吉纳(TNT-DINA)和地恩梯-太安(DNT-PETN)体系的自旋爆轰现象,爆轰波是以低频脉冲方式传播.这些体系具有的爆速、爆热分别为DJ=7.3～7.4km/s和Qv=(5.40±0.01)MJ/kg.不同组成的爆速和爆压PJ通过SW程序计算.用扩散区的爆压P3和爆温T3来评估爆轰波的衰减和重新点火.敏化剂含量相同,梯恩梯-黑索金(TNT-RDX)体系的爆压PJ大于TNT-DINA的爆压,TNT-RDX体系的温度T3比TNT-DINA高60～100K.计算值与实验结果吻合较好.     

Programmable group-delay module using binary polarization switching

We demonstrate the first programmable group-delay module based on polarization switching. With a unique binary tuning mechanism, the device can generate any differential group delay value from -45 to +45 ps with a resolution of 1.40 ps, or any true-time-delay value from 0 to 45 ps with a resolution of 0.7 ps. The delay varying speeds for both applications are under 1 ms and can be as fast as 0.1 ms. We evaluate both the dynamic and static performances of the device while paying special attention to its dynamic figures of merit for polarization-mode dispersion emulation and compensation applications. Our experiment shows that the device exhibits a negligible transient-effect induced power penalty (<0.2 dB) in a 10-Gb/s nonreturn-to-zero system.     

Stabilization of singularly perturbed fuzzy systems

This paper presents some novel results for stabilizing singularly perturbed (SP) nonlinear systems with guaranteed control performance. By using Takagi-Sugeno fuzzy model, we construct the SP fuzzy (SPF) systems. The corresponding fuzzy slow and fast subsystems of the original SPF system are also obtained. Two fuzzy control designs are explored. In the first design method, we propose the composite fuzzy control to stabilize the SPF subsystem with H/sup /spl infin// control performance. Based on the Lyapunov stability theorem, the stability conditions are reduced to the linear matrix inequality (LMI) problem. The composite fuzzy control will stabilize the original SP nonlinear systems for all /spl epsiv//spl isin/(0,/spl epsiv//sup */) and the upper bound /spl epsiv//sup */ can be determined. For the second design method, we present a direct fuzzy control scheme to stabilize the SP nonlinear system with H/sup /spl infin// control performance. By utilizing the Lyapunov stability theorem, the direct fuzzy control can guarantee the stability of the original SP nonlinear systems for a given interval /spl epsiv//spl isin/[/spl epsiv/_,/spl epsiv/~]. The stability conditions are also expressed in the LMIs. Two SP nonlinear systems are adopted to demonstrate the feasibility and effectiveness of the proposed control schemes.     

电阻式电压传感器结构设计及误差特性研究

从路的角度分析了电阻式电压传感器的误差特性 ,从场的角度比较了几种结构方案的幅值误差、相角误差及最大场强 ,优化出最佳方案 ,并分析了该方案幅值误差的频率特性