叔胺萃取分离精炼铂的新工艺

用三烷基胺（Ｎ２３５）萃取分离铂，考察了稀释剂、改质剂浓度、料液酸度对分配系数的影响，从复杂的工业料液中，用Ｎ２３５萃取、洗涤、反萃、再生及精炼铂的工艺技术。     

Electrochemical properties of some cobalt antimonides as anode materi-als for lithium- ion batteries

Some cobalt antimonides have been prepared and studied as the candidate anode materials for lithium ion batter-ies. Reversible capacities of 424,423 and 546 mA·h·g-1 were measured at the first cycle for as-solidified CoSb2, CoSb3 and annealed CoSb3 respectively. A low lithium ions diffusion coefficient in the order of 10-16 m2·s-1 was estimated from the coulometric titration measurements in the annealed CoSb3 electrode. It was found that the electrochemical properties of fine powders are significantly better than coarse powders. However the SEM picture shows that the nano-sized CoSb3 powders gathered to larger granules, which worsens somewhat the capacity retention of the nano-sized materials, although the volume capacities of the annealed and ball milled CoSb3 remain near twice of that of graphite after 50 cycles.     

Temperature Dependence of the Magnetocrystalline Anisotropy in Nd_2Co_(14)B Compound

Easy and hard magnetization curves of Nd_2Co_(14)B compound have been measured withextracting-sample-magnetometer(μ_0H_(max)=6T)at 10～300 K.Magnetic anisotropy constants K_1 and K_2have been determined by fitting the hard magnetization curves,in which only K_1 ,K_2 and misalignment anglehave been taken as fitting parameters.The values of K_1 and K_2 at 4.2 K were derived by extrapolation.Anisotropy coefficients,x_2~° and x_4~°were derived from the anisotropy constants.The anisotropy constant K_2increases rapidly with increasing temperature when TT_(sr).The temperature depen-dence of the magnetic anisotropy coefficient x_2~° was fitted with the formula.The anisotropy coefficients x_2~°can be well described by the tenth-power law from 4.2 K to T_(sr)and by the sixth-power law from T_(sr_ to 300 K.     

40Cr钢渗氮过程中碳原子的迁移

将正火４０Ｃｒ钢样在不同温度下进行不同时间的气体渗氮，对其横断面进行波谱分析，发现渗氮前沿附近自始至终存在着典型的贫碳区，其两侧为富碳区，透射电镜分析结果表明，碳原子的重新分布包括碳化物的回溶、碳的扩散及碳化物长大三个过程。     

(Short communication) Degradation of corrosion resistance of Zircaloy-4 in LiOH aqueous solution

To investigate the degradation of corrosion resistance of Zircaloy-4 in LiOH aqueous solution, SIMS (secondary ion mass spectrometry) analysis was performed to examine the profiles of Li~ , K~ , and OH~- in oxide layers formed in the same concentration (0.1 mol/L) LiOH and KOH solutions. Even though the oxide layers have an equal thickness, the penetration depth of K~ is shallower than that of Li~ , and the penetration depth of OH~- corroded in KOH solution is also shallower than that corroded in LiOH solution. It shows that the diffusion of OH~- into oxide layer is accompanied by the corresponding cation. The difference of degradation effect of LiOH and KOH solutions on the corrosion resistance of Zircaloy-4 was discussed.     

Experimental Study of Microstructure Evolution during Tempering of Quenched Steel and Its Application

LARGE-SIZED FORGINGS are usually intensivelyquenched to obtain the desired microstructuredistribution,high strength and hardness.Becauseresidual stresses are high in quenched large-sizedforgings,tempering processes follow quenchingprocesses to reduce the residual stress and obtain goodmechanical properties.Several differentmicrostructures are generated in quenched steelforgings,such as martensite,bainite and retainedaustenite.Modeling of microstructure evolution inquenched steel during …     

压铸机偶发故障期可靠性管理及应用

机器工作可靠度与机器的固有可靠度和使用可靠度密切相关。设备使用厂家通过对机器偶发故障期使用可靠度的研究，采取有效对策来保证和提高机器工作可靠度，是提高企业效益的途径之一。本文针对压铸机，进行了故障规律分析，介绍了偶发故障期可靠度的计量公式，提供了各故障期的经验数据，详述了应用可靠性技术的基础工作范围和内容，叙述了应用效果     

Morphological evolution of primary TiC carbide in laser clad TiC reinforced FeAl intermetallic composite coating

1　INTRODUCTIONIronaluminumbasedonFeAlintermetallicalloywasexpectedtobeanimportantandpotentialhightemperaturematerial,becauseitsgoodresistancetooxidationandcorrosion ,lowdensityandhightem peraturemelting point[12 ] .However ,theintrinsicpropertiesofFeAlintermetallicalloy ,suchaslowductilityandlowfracturestrength ,limiteditsindus trialapplications .Howtoimprovemechanicalproper tiesofFeAlintermetallicalloyandexpanditsindus trialapplicationrealmwasanimportantresearchas pectformaterialworke…     

Cooling strategies for cryogenic machining from a materials viewpoint

This article discusses the cooling strategies for cryogenic machining from a materials viewpoint. It is argued that, because different materials respond to temperature and machining processes differently, different cooling strategies are needed to improve the machinabilities of materials by cryogenic machining. In this work, five workpiece materials such as AISI1010 low-carbon steel, AISI1070 high-carbon steel, AISIE52100 bearing steel, titanium alloy Ti-6Al-4V, and cast aluminum alloy A390 were studied experimentally at various temperatures. Based on the experimental results of the cryogenic properties of the materials and their known machining characteristics, the cooling strategies for cryogenic machining of these materials were analyzed.     

BREAKAGE MECHANISM OF TUNGSTEN BASED ALLOY BLOCK FOR ELECTRO-HEAT UPSETTING

The breakage mechanism of W-Ni-Fe alloy in the process of electro-heat upsetting studied both theoretically and experimetnally, and also the behaviors of crack formation and propagation were analysed. Alloy suffers from corrosion and thermal-mechanical fatigue mutual function. Simultaneously, the practical ways to improve the anvil life was discussed.