Application of Code Approach for Emergency Evacuation in a Rail Station

This paper presents an emergency evacuation analysis during a mid-platform train fire in an underground rail station. A time-based evacuation scenario is developed taking into account the stairway inaccessibility due to smoke blockage. The calculation approach in NFPA 130 is then applied to a parametric study of this time-based scenario and its reliability is examined using a micro-simulation model. Both methods give consistent predictions of the exiting times. The results demonstrate that with the division of the station into two zones, the exiting time could not meet the code requirements, whereas it does meet the required exiting time without the division. Such division is due to smoke blockage and creates an uneven ratio of the occupant load to the available exiting capacity. This shows that appropriate consideration of the fire and smoke effects is important for station egress evaluation. Other issues such as the fire growth rate and the pre-evacuation time are also discussed.     

Breakdown behavior of GaAs/AlGaAs HBTs

Avalanche breakdown behavior at the collector junction of the GaAs/AlGaAs HBT (heterojunction bipolar transistor) has been studied. Junction breakdown characteristics displaying hard breakdown, soft breakdown, and negative resistance breakdown behavior were observed and are interpreted by analysis of localized microplasma effects, uniform microplasma-free behavior, and associated current gain measurements. Light emission from the collector-base junction of the GaAs/AlGaAs HBT was observed and used to investigate breakdown uniformity. Using a simple punchthrough breakdown model, the theoretical breakdown curves at different collector doping concentrations and thicknesses were computed and found to be in agreement with maximum breakdown voltages measured from devices displaying the most uniform junction breakdown. The serious current gain degradation of GaAs/AlGaAs HBTs at low current densities was analyzed in connection with the measurement of a large collector-emitter breakdown voltage. The unexpected functional relationship between the collector-emitter breakdown voltage and collector-base breakdown voltage is explained by the absence of a hole-feedback effect for devices not exhibiting transistor action     

Residual Stress Simulation of Injection Molding

In this study, distribution and history of residual stresses in plaque-like geometries are simulated based on linear thermoviscoelastic model, which helps to understand the mechanics and evolution of the residual stresses in the injection molding process. The numerical calculation of direction, combined with the specified boundary conditions. Results show that the stress variation across the thickness exhibits a high surface tensile value changing to a compressive peak value close to the surface, with the core region experiencing a parabolic tensile peak. Residual stress distribution throughout the thickness is almost same along the flowpath and the final residual stresses value near the gate is lower than the value near the end of flowpath.     

Theoretical Investigation of Time Suboptimal Control of Industrial Manipulators Along Specified Paths

A method for the time suboptimal control of an industrial manipulator from an initial position and orientation to a final position and orientation as it moves along a specified path is proposed. Nonlinear system equations that describe the manipulator motion are linearized at each time step along the path. A method which gives the control inputs (joint angular velocities) for time suboptimal control of the manipulator is developed. In the formulation, joint angular velocity and acceleration limitations are also taken into consideration. A six degree of freedom elbow type manipulator is used in numerical examples to verify the method developed.     

Mechanical properties of iron processed by severe plastic deformation

In the present study, the mechanical properties of Fe processed via severe plastic deformation (equal-channel angular pressing (ECAP)) at room temperature were investigated for the first time. The grain size of annealed Fe, with an initial grain size of about 200 μm, was reduced drastically during ECAP. After eight passes, the grain size reaches 200 to 400 nm, as documented by means of transmission electron microscopy (TEM). The value of microhardness during pressing increases 3 times over that of the starting material after the first pass and increases slightly during subsequent pressing for higher-purity Fe. Examination of the value of microhardness after eight passes as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization, an observation that resembles the behavior reported for heavily deformed metals and alloys. The tensile and compression behaviors were examined. In tension, a drop in the engineering stress-engineering strain curve beyond maximum load was observed both in the annealed Fe and the ECAP Fe. This drop is related to the neck deformation. The fracture surface, examined by scanning electron microscopy (SEM), shows vein patterns, which is different from the dimples found on the fracture surface of annealed Fe. In compression, an initial strain-hardening region followed by a no-strain-hardening region was observed in the ECAP Fe. The yield strength in tension of the ECAP Fe was observed to be higher than that in compression. The strengthening mechanisms and softening behavior are discussed.     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

Failure Analysis of Fuel System Assemblies

Fuel system assemblies used on recreational watercraft failed after a short time in service in a seawater environment. Examination of the assemblies revealed significant degradation of the polyacetal connectors of the wire subassemblies. Optical and microscopic evaluations indicated the complete loss of connector material implying decomposition of the resin, along with mud-cracking and a rough surface morphology signifying chemical attack. An elemental analysis performed on both an intact connector and degraded connector suggested a potential chemical agent in the form of zinc chloride. At elevated temperatures, concentrated zinc chloride solutions are known to decompose polyacetal resins. The source of the zinc chloride was established as corrosion products that resulted during the dezincification of the internal brass connector through exposure to saltwater in the application.     

AgNO<Subscript>3</Subscript> spray tests: advantages,weaknesses, and various applications to quantify chloride ingress into concrete. Part 1: Non-steady-state diffusion tests and exposure to natural conditions

Within the framework of the evaluation and the prediction of chloride-induced corrosion risks, simple and rapid AgNO₃ spray tests can be proposed for various issues. This paper forms the first part of a series. In this first part, the Maultzsch procedure (spraying of 0.1-N AgNO₃ solution + K₂CrO₄) as well as the procedure based on the use of a sole AgNO₃ solution have been investigated on a broad range of concretes. These procedures have also been compared to the Collepardi procedure (spraying of 0.1-N AgNO₃ + fluoresceine). The feasibility of these colorimetric techniques on saturated specimens cast in laboratory, after non-steady-state diffusion tests carried out in various conditions, is discussed. In addition, the results obtained from applying such spray tests in field conditions on cores drilled out from various RC test specimens exposed to a marine environment (tidal zone) and to a road and cold environment (freezing-thawing cycles and spraying of deicing salts) are presented. Colorimetric methods have in particular been applied here to the assessment of the average chloride penetration depth and of its evolution versus time (kinetics). Moreover, the detection threshold of these techniques has been investigated in various environments. The possible sources of discrepancy on the results have been analysed.     

Detrended Fluctuation Analysis of the Human EEG during Listening to Emotional Music

A nonlinear method named detrended fluctuation analysis （DFA） was utilized to investigate the scaling behavior of the human electroencephalogram （EEG） in three emotional music conditions （fear, happiness, sadness） and a rest condition （eyes-closed）. The results showed that the EEG exhibited scaling behavior in two regions with two scaling exponents β1 and β2 which represented the complexity of higher and lower frequency activity besides α band respectively. As the emotional intensity decreased the value of β1 increased and the value of β2 decreased. The change of β1 was weakly correlated with the ＇approach-withdrawal＇ model of emotion and both of fear and sad music made certain differences compared with the eyes-closed rest condition. The study shows that music is a powerful elicitor of emotion and that using nonlinear method can potentially contribute to the investigation of emotion.