床温及SNCR脱硝对CFB锅炉NOx和N2O排放影响的试验研究

为了研究循环流化床（CFB）锅炉燃用无烟煤时床温及选择性非催化还原（SNCR）脱硝对于NO和N2O排放的影响，在1 MW CFB试验装置上开展了试验研究。结果表明:床温由880 ℃提高到970 ℃，NO排放质量浓度由119.5 mg/m3上升到226.0 mg/m3，N2O排放质量浓度由216.0 mg/m3降低到102.2 mg/m3；在氨氮摩尔比（NSR）为0~3.7之间，随着NSR的提高，脱硝效率从0上升到50.72%；进一步提高NSR到5.2，脱硝效率升至53.61%，增加较为缓慢；随着NSR从0提高到1.7，N2O排放质量浓度由84.3 mg/m3上升至118.3 mg/m3，增长较为缓慢；进一步提高NSR至2.0，N2O排放质量浓度上升至187.7 mg/m3，增长速度提高；继续提高NSR至5.2，N2O排放质量浓度上升至381.4 mg/m3；CFB锅炉采用以尿素为还原剂的SNCR脱硝工艺时，单纯通过加大NSR来提高脱硝效率不仅效果有限，过量喷入的还原剂会造成N2O排放量的显著提高。     

干巴菌多糖提取工艺优化及抗氧化活性的研究

以产于云南曲靖的干巴菌为原料,以多糖提取率为评价指标,采用单因素实验及正交实验优化干巴菌多糖的提取工艺,通过测定干巴菌多糖对DPPH自由基及羟基自由基的清除率来评价其抗氧化活性。结果表明,干巴菌多糖的最佳提取工艺为:提取温度70℃、提取时间2.5 h、料液比1∶15(g∶mL),在此条件下,多糖提取率达到10.08%;当干巴菌多糖浓度为5 mg·mL~(-1)时,其对DPPH自由基的清除率为86.99%,对羟基自由基的清除率为87.46%,有较好的抗氧化作用。     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

铜离子掺杂对高铁低钙水泥熟料性能的影响

基于C4AF可以提高水泥基材料的抗蚀性,以高铁低钙水泥熟料为研究对象,掺入不同含量的CuO,通过对熟料及其水化产物进行X射线衍射(XRD)、水化热、抗压强度、非蒸发水含量和固化氯离子能力等测试,探究Cu2+对高铁低钙水泥熟料水化性能与氯离子吸附固化能力的影响.结果发现,适量CuO的掺入促进了高铁低钙水泥熟料中C4AF的生成,降低了熟料液相的粘度,有利于C3S的晶粒生长,有利于提高高铁低钙水泥熟料的水化活性和固化氯离子能力,最佳掺量为0.2 wt％.     

Eight-node conforming straight-side quadrilateral element with high-order completeness (QH8-C1)

A new eight-node conforming quadrilateral element with high-order completeness, denoted as QH8-C1, is proposed in this article. First, expressions for the interpolation displacement function satisfying the requirements for high-order completeness in the global coordinate system are constructed. Second, the displacement function expression in global coordinates is transformed into isoparametric coordinates, and the relationships between the two series of coefficients for the two kinds of displacement function expressions are found. Third, the displacement function expression is modified to satisfy the requirements of nodal freedom and interelement boundary continuity. The key to the new element construction is the derivation of the linear relationship expressions among 12 coefficients of element displacement interpolation polynomials in the global and isoparametric coordinate systems. As a result, the relationship between quadratic completeness and interelement continuity is explicitly given, and a proof of the completeness and the continuity was conducted to theoretically guarantee the validity of the derivation results. Furthermore, in order to verify the correctness of the theoretical work, nine numerical examples were performed. The computation results from these examples demonstrate that QH8-C1 exhibited excellent performance, including high simulation accuracy, fast convergence, insensitivity to mesh distortion, and monotonic convergence.     

区域导航对流层延迟误差修正模型研究

本文研究了电波大气折射理论，分析了传播误差因素，阐述了区域导航信号的传播路径与 GNSS 卫星导航的不同，论述了对流层延迟对区域导航信号测量精度的影响，设计了满足区域导航系统应用需求的对流层延迟误差修正模型，并通过仿真研究，验证了所设计区域导航对流层延迟误差修正模型的可行性，并给出了该模型在远距离低仰角和近距离高仰角下的误差修正能力。     

中速柴油机机体铸造裂纹的原因分析及防止措施

根据柴油机机体裂纹产生的原因,对机体裂纹缺陷进行分析,找到了机体裂纹产生的主要原因。其主要原因可概括为铸件结构、化学成分、铸件补缩条件及开箱温度等,针对裂纹的主要原因采取相应的措施后,裂纹缺陷得到了根本的控制。     

Fabrication of Cu/graphite film/Cu sandwich composites with ultrahigh thermal conductivity for thermal management applications

Effective thermal management of electronic integrated devices with high powder density has become a serious issue, which requires materials with high thermal conductivity (TC). In order to solve the problem of weak bonding between graphite and Cu, a novel Cu/graphite film/Cu sandwich composite (Cu/GF/Cu composite) with ultrahigh TC was fabricated by electro-deposition. The micro-riveting structure was introduced to enhance the bonding strength between graphite film and deposited Cu layers by preparing a rectangular array of micro-holes on the graphite film before electro-deposition. TC and mechanical properties of the composites with different graphite volume fractions and current densities were investigated. The results showed that the TC enhancement generated by the micro-riveting structure for Cu/GF/Cu composites at low graphite content was more effective than that at high graphite content, and the strong texture orientation of deposited Cu resulted in high TC. Under the optimizing preparing condition, the highest in-plane TC reached 824.3 W·m⁻¹·K⁻¹, while the ultimate tensile strength of this composite was about four times higher than that of the graphite film.     

单次反射ATR-FTIR红外光谱法在涂膜表面成分分析中的应用

运用傅里叶变换衰减全反射红外光谱法(ATR-FTIR)中的单次反射法对水性偏氯乙烯-丙烯酸酯共聚物薄膜进行辅助定性研究,考察了具有不同偏氯乙烯单体含量的共聚物薄膜的红外谱图变化。同时运用单次反射ATR-FTIR法对施工现场取回的红色脱落涂膜进行定性分析。     

2014年聚酯产业链供需状况及发展趋势

介绍了聚酯产业链供需现状,对未来几年聚酯产业链发展趋势做了分析和研究,并提出相关建议。