Poly(3‐chlorothiophene) films prepared by the direct electrochemical oxidation of 3‐chlorothiophene in mixed electrolytes of boron trifluoride diethyl etherate and sulfuric acid

3‐Chlorothiophene (CT) was electrochemically polymerized in mixed electrolytes of a boron trifluoride diethyl etherate solution containing 0–20% (by volume) sulfuric acid. The oxidation potentials of the monomer in these media were measured to be only 1.06–1.31 V (vs Ag/AgCl). These values were much lower than that of CT in acetonitrile and 0.1 mol/L (Bu)₄NBF₄ (1.92 V vs Ag/AgCl). Poly(3‐chlorothiophene) (PCT) films with conductivities of 0.1–2 S cm^?1 were obtained. The structure, morphology, and electrochemical behavior of the PCT films also were investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 502–509, 2003     

Strain-induced crystallization,Part IV: Induction time analysis

The empirical equation, 1/t_i = Ae^Ei/RT, which expresses the exponential dependence of the reciprocal of crystallization induction time, t_i, has been analyzed and shown to be equivalent to the nucleation rate equations derived earlier in Part III (1). Consequently we have used the t_i measurements obtained earlier by Krueger and Yeh to calculate not only the nucleation rate enhancements but also the melting point elevations, the relative crystal thickness changes and molecular coil extension ratios of shear-crystallization polyethylene. It is shown that polyethylene when crystallized between 129 and 131°C at shear rates between 1.56 and 9.70 sec^?1 can have melting point increases of 4.2 to 7.2°C and crystal thickness decreases of 20 to 25 percent, when compared to those crystallized at 130°C in the quiescent state. The predicted “coil” extension in the melt just prior to shear-induced crystallization ranges between 21 and 36 percent. The results of these analyses as well as those on nucleation rates of polyethylene oxide are discussed in detail.     

可降解聚丙烯发泡塑料初探

开发可降解聚丙烯(PP)发泡制品具有广阔的发展前景。PP自身的化学结构特点使其具有比其它聚烯烃和PS更优异的降解性能。在PP中添加各种光降解剂,或引入光敏基团可以促进PP的光降解性;将其与天然高分子或各种可降解塑料混合也可以有效促进PP的生物降解;将降解和发泡的配方和工艺合理结合以获得光降解性、生物降解性或光 生物双降解的发泡PP制品是完全可能的。     

Thermally stimulated depolarization current studies on strain-induced relaxations in polymers

Thermally stimulated depolarization current (TSD) method has been used to study the molecular relaxation from room temperature up to the glass-transition temperature for three plastically deformed polymers. A well-defined distinct α′ peak has been observed in the vicinity of 70°C for polycarbonate, polysulfone, as well as poly(ethylene terephthalate), that had been annealed above T_g and subsequently cold-rolled. Since this relaxation is not observed after the initial measurements, it is a nonequilibrium relaxation. In the case of polycarbonate, the nonreversible α′ process had an activation energy ranging from 1.22 to 1.75 eV and an intensity proportional to the degree of deformation resulting from cold-rolling. The spontaneous polarization in the rolled material was believed to originate from the initial anisotropy which was subsequently enhanced by the rolling process. Density measurements, as well as the birefringence observation, have been performed on the rolled specimens. All the studies led to the conclusion that the molecular motion responsible for this α′ peak was the disorientation of local chain segments from their aligned conformation frozen in during the cold-work.     

脂肪醇聚氧乙烯醚的厌氧与好氧生物降解性

以脂肪醇聚氧乙烯醚(AEO)为目标污染物，在等同条件下做厌氧消化污泥和好氧活性污泥对其生物降解性能的对比实验，得出了同一系列AEO分子中聚氧乙烯基与整个分子的降解难易程度的关系。表明：①污泥会对AEO分子产生吸附一脱附作用而出现假降解率，克服假降解率的干扰是准确测定AEO生物降解性的关键因素；②厌氧和好氧条件下，AEO均可降解，但厌氧降解要稍优于好氧降解；③AEO中聚氧乙烯基的单元数(n)是影响其生物降解的重要因素，相同碳链的直链烷基，生物降解率随n的增加而明显降低。     

四种杀菌剂对枸杞黑果病的防治效果

枸杞黑果病是枸杞产区的主要病害．发病后造成黑花、黑蕾和黑果，使枸杞产量降低，品质变劣。为探明四种杀菌剂对枸杞黑果病的防治效果及最佳剂量，2003年对下述四种杀菌剂进行了田间药效对比试验，调查防效结果如下：20％三苯基醋酸锡WP450～281g／hm^2(以有效成分计，下同)，20％氟硅唑EC21．08g／hm^21．5％噻霉酮EW16、88～21．08g／hm^2、40％氟硅唑EC450g／hm^2和70％甲基托布津WP787．5g/hm^2对枸杞黑果病防效均在88．25％以上。经LSD检验各处理间防效无显著差异。     

BELL整体比例调节型电动执行机构的电路连接与调试方法

天津贝尔自动化仪表技术有限公司引进法国先进技术,生产的电动执行机构广泛用于自动控制系统。新一代“卓越引进系列”具有多种保护功能和多种控制方式,更适宜现代工控需求。在百种以上规格中,搞清楚最基本类型——标准整体比例调节型是其他类型的基础。文章结合厂家提供的资料,针对整体比例调节型电动执行机构的重要方面进行了深入的分析与总结：一是组成与原理框图;二是电路器件的作用与电路连接;三是调试的项目与具体方法。     

硫醇自组装膜的电化学研究进展

综述了在金电极上硫醇自组装膜的电化学表征方法，性质和应用，介绍了自组装膜上的电子传递机理，并进行了简要的展望。     

发酵工厂中空气净化工艺的合理选择

从节能、降低成本、优化工艺的角度，对无菌空气制备过程中，空气预处理流程的选择、空气净化设备、过滤介质以及设备的遴选进行探讨，以实现工艺和工程设计的优化结合。     

纳米碳酸钙的表面活化改性研究

本文主要介绍通过加入特定的表面改性剂,制得了表面改性的活性碳酸钙.并对活化过程中的一系列影响因素,如活化温度、活化时间、碳酸钙悬浊液浓度、表面改性剂用量进行了研究.