Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers     

计算机远程控制系统的设计与实现

介绍了一个计算机远程控制系统的设计与实现，该系统采用客户机／服务器模式，实现远程屏幕的实时传输，采用LZW压缩算法对图像进行压缩传输，在接受方进行解码并且实现了远程文件创建和删除、显示被控制端的主机信息、发送实时消息等功能。采用鼠标，键盘的模拟方式对计算机进行实时控制。     

智能电动机控制器在电收尘通风机上的应用

对智能电动机控制器的情况作了介绍，结合工作实践提出了维护要点和建议，并对该控制器的参数设置进行了说明，这对使用该设备的工业企业有一定的指导意义。     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

基于作业测定技术的后桥壳生产线工艺评价及优化

以某企业后桥壳生产线为研究对象,运用作业测定技术中的时间研究法,测定后桥壳各工序的标准时间,评价工艺及找到瓶颈工序;运用"5W1H"提问技术,根据"ECRS"原则,同时结合工艺设计及企业资源情况,对后桥壳生产线现有工艺进行评价及优化,改善后,使生产线的产能每天提高了10件,生产能力提高了33.57%.     

基于MoCA标准的家庭网络研究

本文描述了一种基于MOCA标准的家庭网络,并对该网络及设备进行了基本性能的测试.本文首先介绍了家庭网络的发展现状,对目前的各种家庭网络标准进行了比较.在此基础上详细描述了基于MOCA标准的家庭网络,并对该网络的设计,实现、网络性能进行了详述.然后对该网络进行了测试并得出了相关的测试结论.最后指出该网络的不足及改进之处.     

高分辨率合成孔径雷达图像舰船检测方法

寻找针对高分辨率SAR图像的舰船目标检测算法。利用KSW双阈值分割技术，其效果比传统检测方法好，有利于进一步的目标分类和识别。且必须根据SAR图像分辨率来选择舰船检测算法。     

某铁路医院加速器室大体积防射线混凝土施工

结合大同铁路分局中心医院直线加速器室工程实际，介绍了大体积防射线混凝土的特点及施工中应注意的事项，并阐述了具体的施工技术。