带隔板底水油藏油井临界产量计算公式

本给出了带隔板底水油藏油井的监界产量计算公式，它适用于所有带隔板底水油藏的油井。     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

The correlation of texture and magnetic properties in Co-Cr films

This investigation focuses on the correlation between the crystallographic orientation of grains with respect to magnetic properties in Co-Cr films. Based on a distribution measured for the (0002) crystallographic pole densities, modified formulae describing the texture were used to calculate the coercivity Hc, the squareness ratio Rs (Mr⊥/TMs) and the anisotropy field Ha for Co-Cr films. In general, calculated values for the coercive force He agreed well with the measured values. The calculated Rs⊥. values were much larger than the measured ones, however, indicating that the influence of the demagnetizing field and the magnetostriction on the orientation of the magnetization cannot be neglected. On leave from Institute of Computing Technology, Academia Sinica, P.O.Box 2704-6, Beijing, P.R. China.     

A hybrid spreading/despreading function with good SNR performancefor band-limited DS-CDMA

Code-division multiple-access (CDMA) implemented with direct-sequence spread spectrum (DS/SS) signaling is a promising multiplexing technique for cellular telecommunications services. The efficiency of a direct-sequence spread-spectrum code-division multiple-access (DS-CDMA) system depends heavily on the shape of the spectrum of the spread signal. Maximum efficiency is obtained with an ideal brick-wall bandpass spectrum. There are two approaches toward achieving such a spectrum. One is to use a simple spreader that produces a broad spectrum and then follow it with a precise, high order filter to band limit the spectrum. A second approach, which is the approach taken in this paper, is to use a spreader that produces a spectrum close to the ideal spectrum and then employ a simple filter to control the out-of-band power. The proposed spreader/despreader is based on a simple hybrid function and can be easily implemented. An analysis provides a compact expression for the signal-to-noise ratio (SNR) of a RAKE receiver. The expression includes the effects of baseband, intermediate frequency (IF) and RF filtering as well as the effects of the spectral densities of the spreading/despreading functions. The analysis shows that the proposed spreader/despreader yields superior performance over a conventional pseudo noise (PN) spreading/despreading mechanism     

High-frequency small signal AC and noise modeling of MOSFETs for RFIC design

High-frequency (HF) AC and noise modeling of MOSFETs for radio frequency (RF) integrated circuit (IC) design is discussed. A subcircuit RF model incorporating the HF effects of parasitics is presented. This model is compared with the measured data for both y parameter and f_T characteristics. Good model accuracy is achieved against measurements for a 0.25 μm RF CMOS technology. The HF noise predictivity of the model is also examined with measured data. Furthermore, a methodology to extract the channel thermal noise of MOSFETs from HF noise measurements is presented. By using the extracted channel thermal noise, any thermal noise models can be verified directly. Several noise models including the RF model discussed in this paper have been examined, and the results show that the RF model can predict the channel thermal noise better than the other models     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

LDD方法在提高电路工作电压中的应用研究

研究了利用轻掺杂漏结构来制作高电源电压器件的工艺方法。分析了ＬＤＤ结构参数对器件击穿特性的影响，并结合实验结果对Ｎ＾－区的注入剂量，长度及引入的串联电阻进行了优化设计。     

Automatic fault detection, isolation, and recovery in transparentall-optical networks

Network fault identification is an important network management function, which is closely related to fault management and has an impact on other network management functions such as configuration management, and performance management. This paper investigates fault surveillance and fault identification mechanisms for a transparent optical network in which data travels optically from the source node to the destination node without going through any optical-to-electrical (O/E) or electrical-to-optical (E/O) conversion. Mechanisms and algorithms are proposed to detect and isolate faults such as fiber cuts, laser, receiver, or router failures. These mechanisms allow nonintrusive device monitoring without requiring any prior knowledge of the actual protocols being used in the data transmission     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。