GSM与WCDMA无线网络规划比较

WCDMA与GSM在空中接口上存在较大差异,WCDMA基于码分多址技术,GSM基于时分多址技术。GSM主要处理语音和低速数据,而WCDMA引入了多种速率的数据业务,根据业务的QoS进行资源控制和分配,因此在无线网络规划方法上,WCDMA与GSM存在较大差异。文章从容量规划、覆盖规划、蜂窝布局、规划流程、网络评估等方面对WCDMA与GSM的无线网络规划进行了比较和分析。     

IPv6 delay and loss performance evolution

Although packet delay and loss are two important parameters of the Internet performance, to the best of our knowledge, the evolution of large‐scale IPv6 delay and loss performance has previously not been studied. In this paper, we analyze more than 600 end‐to‐end IPv6 paths between about 26 testboxes of RIPE Network Coordination Centre over two years, and compare the delay and loss performance over time with their IPv4 counterparts. We present and discuss the measurement methodologies and show that IPv6 paths have a higher delay and loss than their IPv4 counterparts. The main reason for the worse performance stems from IPv6‐in‐IPv4 tunnels rather than from native IPv6 paths and such tunnels are still widely used today. Copyright © 2007 John Wiley & Sons, Ltd.     

宣钢1260 m3高炉扩容大修改造设计

宣钢l260m^3高炉大修改造时将炉容扩大到l350m^3，对高炉本体系统设备及冷却系统、自动控制及检测系统进行了全面的改造更新，在炉腹、炉腰及炉身下部高热负荷区域采用铜冷却壁，取消炉身中上部铸铁冷却壁凸台，并采用薄内衬等先进、适用、可靠、成熟的技术。     

Mechanism of resistance microwelding of crossed fine nickel wires

Resistance microwelding of fine crossed nickel wires is of increasing industrial importance for electrical connections in downsized electronic and medical devices, but the understanding of the process is very limited. A study has, therefore, been performed to clarify the basic joining mechanisms, in which the effects of main process parameters (welding current and force and weld time) were investigated by detailed mechanical testing and metallurgical examinations. A bonding mechanism with main process stages (wire cold collapse, surface melting, molten-phase squeeze-out and, solid-state bonding) was proposed. A new technique has also been developed to optimize the process by initiating the welding current well before the electrode force has reached its full nominal value.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

应用均匀设计法研究安息香缩合工艺

利用均匀设计法通过SPSS10.0计算机软件研究了反应条件对安息香缩合的影响。从而获得优化的工艺条件，与正交试验相比，该法试验次数少。工作效率高，并且便于分析各种因素的影响。     

���þ��ܰ�ȫ�Բ�������������

本文通过对在用钻机井架的现场实际测试,建立数据库、测评模型,对实测的数据用计算机技术进行分析,提出了初始弯曲应力;数据正态分布检验——x～2检验;建立回归方程;在给定置信度下测评当前承载能力的技术概念。解决了在用钻机A型井架的安全性评估问题,是一种较为合理、可靠、科学的测评技术和方法。     

Effect of processing history on the properties of Ag-based tapes

The Bi-system tapes and coils were prepared by the powder-in-tube method. The effect of processing and heat treatment on the properties of the tapes and coils was studied. It is found that the shearing stress produced by the rolling process may destroy the 2223 phase, and the destroyed 2223 phase cannot be recovered by heat treatment, whereas the pressing stress produced by the uniaxial pressing process only makes the 2223 phase grains break, and the broken 2223 phase can be closed by the heat treatment. TheJ _c values of the rolling samples, pressing sample, and the coil with a diameter of 35 mm are over 1.3×10⁴, 2.5×10⁴, and 4×10³ A/cm² (77 K, 0 T), respectively.