Optimal design of elastic beams with segmentwise constant height in the case of dynamic loading

A shape optimization method for elastic beams with segmentwise constant height is proposed. The ends of the beam are simply supported, clamped or free. Two problems are discussed; (i) a beam is loaded by lateral pressure, (ii) a beam is struck by an attached mass. External loads and volume of the beam are prescribed and the deflection in a given cross-section is to be minimized. For solving this problem, the deflections are expanded into a Fourier series by eigenfunctions. Numerical results are given for two-, three- and four-stepped beams.     

Fabrication of multi-walled carbon nanotube reinforced polyelectrolyte hollow nanofibers by electrospinning

Hybrid hollow multi-walled carbon nanotubes (MWCNTs)/polyelectrolytes (PE) nanofibers were prepared by a combination of the electrospinning method and layer-by-layer (LbL) technique. The mixed polystyrene (PS)/MWCNTs nanofibers were obtained by electrospinning method, which were employed as templates to self-assembly multilayered polyelectrolytes by LbL technique. Hollow MWCNTs/PE nanofibers were obtained by selectively removed part of the template: PS, which is confirmed by Raman spectra, transmission electron microscopy (TEM) and scanning electron microscopy (SEM).     

Preparation of gold nanoparticles (GNP) aqueous suspensions by a new method involving Tiron

A new method is proposed to produce gold nanoparticles (GNP) by in situ reduction of a gold salt dissolved in water. The reducing agent used is Tiron instead of the citrate anion most often mentioned in literature. The influence of various parameters has been investigated, such as the content of Tiron with respect to that of the precursor of gold HAuCl₄, or the initial pH of the solution after mixing of reactants. It is shown that Tiron also exerts a positive influence as a dispersant, which impedes agglomeration of gold nanoparticles. The typical average size of GNP synthesized in the present work is close to 7 nm.     

3D Hair sketching for real-time dynamic & key frame animations

Physically based simulation of human hair is a well studied and well known problem. But the “pure” physically based representation of hair (and other animation elements) is not the only concern of the animators, who want to “control” the creation and animation phases of the content. This paper describes a sketch-based tool, with which a user can both create hair models with different styling parameters and produce animations of these created hair models using physically and key frame-based techniques. The model creation and animation production tasks are all performed with direct manipulation techniques in real-time.     

A rubber-modified thermoplastic where the morphology produced by phase-separation induced by polymerization disappears at high conversions

An unexpected experimental finding is reported where the primary morphology developed during polymerization-induced phase separation in a rubber-modified thermoplastic practically disappears at high conversions. This process was evidenced by light scattering (LS) and scanning electron microscopy (SEM) for a particular composition of solutions of polyisobutylene oligomers (PIB) in isobornylmethacrylate (IBoMA), during the free-radical polymerization of the monomer. The primary phase separation produced a dispersion of domains rich in PIB containing significant amounts of the monomer (IBoMA). Polymerization of the monomer in these domains occurred at high overall conversions producing the filling of dispersed domains with a PIBoMA-PIB blend that could not be distinguished from the matrix. Under these conditions the final material had the appearance of a homogeneous blend.     

Vibration cavitation behaviour of selected Ni-Mn-Ga alloys

Vibration cavitation erosion tests were carried out on Ni-Mn-Ga alloys of three different crystal structures: (1) the cubic austenite, (2) the non-modulated tetragonal martensite (T) and (3) the five-layered martensite (5M). All Ni-Mn-Ga alloys exhibited cavitation behaviour characterized by a step-wise curve of mass loss versus test time. This behaviour is correlated to the microstructural nature of the alloys as well as the surface conditions of the pre-test samples. The type and concentration of the defects at the surfaces were critical to the cavitation resistance of the alloys. The best cavitation resistant alloy was of a cubic austenitic structure, followed with the alloy of a tetragonal T-martensite. The largest material loss was found in the alloy with a 5M martensite. All the studied Ni-Mn-Ga alloys had an excellent cavitation resistance compared to that of the reference stainless steel, and they even excelled some NiTi alloys found in literature. This may be due to the superelasticity of the cubic austenite and the twinning of the martensitic phases.     

Thomas Fincke und die <Emphasis Type="Italic">Geometria rotundi</Emphasis>

Thomas Fincke (January 6^th, 1561–April 24^th, 1656), born in Flensburg (Germany), was one of the very most important and significant scientists in Denmark during the seventeenth century, a mathematician and astrologer and physician in the beginning of modern science, a representative of humanism and an influentual academic organizer. He studied in Strasbourg (since 1577) and Padua (since 1583) and received his M.D. in Basel (1587), he practised as a physician throughout his life (since 1587 or 1590) and became a professor at Copenhagen (1591). But he was best known because of his Geometriae rotundi libri XIIII (1583), a famous book on plane and spherical trigonometry, based not on Euclid but on Petrus Ramus. In this influentual work, in which Fincke introduced the terms tangent and secant and probable first noticed the Law of Tangents and the so-called Newton-Oppel-Mauduit-Simpson-Mollweide-Gauss-formula, he showed himself to be „abreast of the mathematics of his time“.      

煤系高岭土制备裂化催化剂的探索性研究

从石嘴山煤系高岭土的分析测实,经过改性处理,实验后得出具有碱改性条件,且制备裂化催化剂后重油转化能力有明显提高,开拓了煤系高岭土在石化领域的应用。     

Rectus abdominis muscle flap (RAMF) technique for the management of bladder exstrophies: late clinical outcome and urodynamic findings

OBJECTIVE: To investigate the efficacy of the rectus abdominis muscle flap (RAMF) technique for the closure and augmentation of small, non-compliant bladder exstrophies. PATIENTS AND METHODS: The RAMF technique was used in two girls and two boys (mean age at operation, 31.7 months, range 3-72) with bladder exstrophy. The clinical outcome and urodynamics were assessed during a follow-up of 29 months to 6 years (mean 49.2 months) and included imaging, cystoscopy, biochemical and microbiological studies. RESULTS: There were no urinary tract infections, metabolic problems or electrolyte disturbances and kidney function remained normal in all patients. Radiography confirmed intact function and anatomy of the urinary tract and cystoscopy showed complete coverage of the inner peritoneal layer of RAMF with uroepithelium. No stone formation or mucus production were detected. Currently, three patients void using clean intermittent catheterization through the native urethra and the fourth through an appendiceal Mitrofanoff valve. However, the bladder volume was insufficient at the late follow-up and three patients required bladder augmentation. CONCLUSIONS: The RAMF technique is a good alternative for closing bladder exstrophies and achieves an increase in bladder capacity; however, although there is a mild improvement in bladder capacity and compliance. RAMF should not be used as a bladder augmentation procedure. The technique is indicated in the closure of large bladder defects, bladder exstrophies with small, inelastic, non-compliant bladder remnants and failed primary closures.     

一种新型陶瓷材料及其耐磨性

对新型Ａｌ２Ｏ３－ＴｉＣ－Ｃｏ陶瓷的磨粒磨损，冲蚀磨损及其在单颗粒作用下的摩擦磨损行为进行了研究。与ＡＴ３０（７０ｗｔ％Ａｌ２Ｏ３－３０ｗｔ％ＴｉＣ）陶瓷相比，Ａｌ２Ｏ３－ＴｉＣ－Ｃｏ陶瓷具有更为良好的耐磨性，金属钴的存在提高了基体的韧性，细化了晶粒，其综合力学性能得到了显著提高，ＡＴＣ陶瓷样品耐磨性与其强韧化水平和细致的组织结构有关。