A delta transform approach to loop gain-phase shaping design of robust digital control systems

This paper addresses the existence of loop gain-phase shaping (LGPS) solutions for the design of robust digital control systems for SISO, minimum-phase, continuous-time processes with parametric uncertainty. We develop the frequency response properties of LGPS for discrete-time systems using the Δ-transform, a transform method that applies to both continuous-time and discrete-time systems. A theorem is presented which demonstrates that for reasonable specifications there always exists a sampling period such that the robust digital control problem has a solution. Finally, we offer a procedure for estimating the maximum feasible sampling period for LGPS solutions to robust digital control problems.     

Robust crossfeed design for hovering rotorcraft

Control law design for rotorcraft fly-by-wire systems normally attempts to decouple the angular responses using fixed-gain crossfeeds. This approach can lead to poor decoupling over the frequency range of pilot inputs and increase the load on the feedback loops. In order to improve the decoupling performance, dynamic crossfeeds should be adopted. Moreover, because of the large changes that occur in the aircraft dynamics due to small changes about the nominal design condition, especially for near-hovering flight, the crossfeed design must be ‘robust’. A new low-order matching method is presented here to design robust crossfeed compensators for multi-input, multi-output (MIMO) systems. The technique minimizes cross-coupling given an anticipated set of parameter variations for the range of flight conditions of concern. Results are presented in this paper of an analysis of the pitch/roll coupling of the UH-60 Black Hawk helicopter in near-hovering flight. A robust crossfeed is designed that shows significant improvement in decoupling perfomance and robustness over the fixed-gain or single point dynamic compensators. The design method and results are presented in an easily used graphical format that lends significant physical insight to the design procedure. This plant precompensation technique is an appropriate preliminary step to the design of robust feedback control laws for rotorcraft.     

Multi-input,multi-output flight control system design for the YF-16 using nonlinear QFT and pilot compensation

Nonlinear quantitative feedback theory (QFT) and pilot compensation techniques are used to design a 2 × 2 flight control system for the YF-16 aircraft over a large range of plant uncertainty. The design is based on numerical input-output time histories generated with a FORTRAN implemented nonlinear simulation of the YF-16. The first step of the design process is the generation of a set of equivalent linear time-invariant (LTI) plant models to represent the actual nonlinear plant. It has been proven that the solution to the equivalent plant problem is guaranteed to solve the original nonlinear problem. Standard QFT techniques are then used in the design synthesis based on the equivalent plant models. A detailed mathematical development of the method used to develop these equivalent LTI plant models is provided. After this inner-loop design, pilot compensation is developed to reduce the pilot's workload. This outer-loop design is also based on a set of equivalent LTI plant models. This is accomplished by modelling the pilot with parameters that result in good handling qualities ratings, and developing the necessary compensation to force the desired system responses.     

Flexible, dry-released process for aluminum electrostatic actuators

We present an all-aluminum MEMS process (Al-MEMS) for the fabrication of large-gap electrostatic actuators with process steps that are compatible with the future use of underlying, pre-fabricated CMOS control circuitry. The process is purely additive above the substrate as opposed to processes that depend on etching pits into the silicon, and thereby permits a high degree of design freedom. Multilayer aluminum metallization is used with organic sacrificial layers to build up the actuator structures. Oxygen-based dry etching is used to remove the sacrificial layers. While this approach has been previously used by other investigators to fabricate optical modulators and displays, the specific process presented herein has been optimized for driving mechanical actuators with relatively large travels. The process is also intended to provide flexibility for design and future enhancements. For example, the gap height between the actuator and the underlying electrode(s) can be set using an adjustable polyimide sacrificial layer and aluminum “post” deposition step. Several Al-MEMS electrostatic structures designed for use as mechanical actuators are presented as well as some measured actuation characteristics     

MANAGEMENT SUPPORT SYSTEM AT PROMUS Using IT to Ensure Customer Satisfaction

Information-based organizations are structured to function with as small and efficient a staff as possible. To this end, executives at The Promus Companies are using IT to spread decision-making authority and responsibility for customer satisfaction and customer service throughout the organization.     

MEETING THE IT CHALLENGES OF BUSINESS The Changing Mandate for MBAs

What is the implication for business when information technology (IT) changes in the workplace without a commensurate change in the composition of business programs educating tomorrow's employees? A survey of MBA graduates forms the basis of this article on the IT skills needed in the marketplace.     

PARTNERS IN EXCELLENCE Metrics and Productivity Programs

For many companies, productivity improvements are the watchwords of the 1990s. IS organizations are having to demonstrate increased productivity on an annual basis. For the end-user computing (EUC) department, this requirement often comes in addition to the request to quantify the services it provides, presenting the EUC manager with the proverbial nightmare of juggling two number-one priorities. Which should receive the highest attention? The savvy manager recognizes that the correct answer is both.     

Base-type languages: Program design by upper semantic approximation

Translated from Kibernetika i Sistemnyi Analiz, No. 4, pp. 140–155, July–August 1994.