Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

A novel way to treat refractory waste: Sonication followed by wet oxidation (SONIWO)

The effectiveness of the hybrid system sonication followed by wet oxidation (SONIWO) to treat otherwise refractory waste has been demonstrated. In such a hybrid system homogeneous CuSO₄ catalyst was found to be very efficient.     

Cold forging and chemical heat treatment of the casing of the internal joint for VAZ cars

The technological process of cold forging applied for the first time in the production of the casing of the internal joint with races is described. The process operations of cold forging and the annealing and carburizing regimes for this part me described.     

Increasing the interference immunity of broadband systems for measuring and transmitting information by utilizing nonlinear signal processing methods

A method is considered for increasing the immunity from interference of broadband systems for measuring and transmitting information. It is based on utilizing nonlinear methods to process spread-spectrum signals. The possibility is investigated of using a quasioptimal receiving device which can be implemented in practice. It is shown that the proposed method makes it possible to solve the rejection problem at the physical level. Translated from Izmeritel'naya Tekhnika, No. 11, pp. 13–15, November, 1996.     

Nitric oxide reduction and carbon monoxide oxidation over carbon-supported copper-chromium catalysts

Carbon supported copper-chromium catalysts are shown to be very active for both the reduction of nitric oxide with carbon monoxide and the oxidation of carbon monoxide with oxygen. Mixed copper-chromium oxide active phases have good activity in the simultaneous removal of nitric oxide and carbon monoxide from exhaust gases. The influence of several catalyst variables has been investigated. The activity per volume of catalyst increases with increasing loading, while the intrinsic activity shows a maximum around C/M=100−50. An optimum catalyst for nitric oxide reduction and carbon monoxide oxidation has a copper/chromium ratio of 2/1. The apparent activation energy for the carbon monoxide oxidation over carbon supported copper-chromium catalysts is 77 kJ/mol, suggesting that the Cu---O bond rupture is the rate-limiting process. The reduction of nitric oxide takes place at higher temperatures. Since all catalysts have a low selectivity for molecular nitrogen formation at lower temperatures, the dissociation of nitric oxide is probably rate determining, resulting in a slightly reduced catalyst system. In an excess of carbon monoxide the reaction is first-order in nitric oxide and zero-order in carbon monoxide. Moisture inhibits the reaction by reversible competitive adsorption, whereas carbon dioxide does not. Oxygen completely inhibits the reduction of nitric oxide due to the more rapid reoxidation of the catalytic sites compared to nitric oxide. Therefore, the reduction of nitric oxide takes place only when all oxygen has been converted and, hence, is shifted to higher temperatures. As a possible consequence, the production of nitrous oxide is reduced. Nitric oxide and molecular oxygen react preferentially with carbon monoxide, so, in an excess of oxidizing component, gasification of the carbon support occurs at higher temperatures after carbon monoxide has been completely consumed.     

Afterburner [network-independent card for protocols]

Many current implementations of protocols such as the Transmission Control Protocol/Internet Protocol (TCP/IP) are inefficient because data are often accessed more frequently than necessary. Three techniques that reduce the need for memory bandwidth are proposed. The techniques are copy-on-write, page remapping, and single-copy. Afterburner, a network-independent card that provides the services that are necessary for a single-copy protocol stack, is described. The card has 1 MByte of local buffers and provides a simple interface to a variety of network link adapters, including HIPPI and asynchronous transfer mode (ATM). Afterburner can support transfers to and from the link adapter card at rates up to 1 Gbit/s. An implementation of TCP/IP that uses the features provided by Afterburner to reduce the movement of data to a single copy is discussed. Measurements of the end-to-end performance of Afterburner and the single-copy implementation of TCP/IP are presented     

Climatic solar roof: an ecological alternative to heat dissipation in buildings

A new system based on the harnessing of solar and wind power is presented for heat dissipation in air conditioning facilities. The innovation offered by the new system is the integration of two well-known subsystems: a cooling tower and a solar chimney which increases the air flow without the use of electric power. The system is described and presented together with a model for its study. The field data acquired from the prototype built in southern Spain establishes the actual potential of the system, which provides a new approach to a sustainable technological development.     

Experience in High-Temperature Thermomechanical Treatment with Helical Reduction in the Production of Axisymmetric Parts

Metal Science and Heat Treatment -     

Dynamic and equilibrium swelling of DVB-crosslinked polystyrene particles

The dynamic and equilibrium swelling behavior of polystyrene microparticles crosslinked with divinyl benzene was investigated in methyl ethyl ketone and cyclohexane. The dynamic studies gave new information about the mechanism of penetrant transport in this polymer. The equilibrium studies were used to determine important parameters of the crosslinked structure of these systems, including the average molecular weight between crosslinks, M?_c