Remotely powered addressable UHF RFID integrated system

This paper presents a fully integrated remotely powered and addressable radio frequency identification (RFID) transponder working at 2.45 GHz. The achieved operating range at 4 W effective isotropically radiated power (EIRP) base-station transmit power is 12 m. The integrated circuit (IC) is implemented in a 0.5 /spl mu/m silicon-on-sapphire technology. A state-of-the-art rectifier design achieving 37% of global efficiency is embedded to supply energy to the transponder. The necessary input power to operate the transponder is about 2.7 /spl mu/W. Reader to transponder communication is obtained using on-off keying (OOK) modulation while transponder to reader communication is ensured using the amplitude shift keying (ASK) backscattering modulation technique. Inductive matching between the antenna and the transponder IC is used to further optimize the operating range.     

Second-harmonic generation in GaAs-based quantum-cascade lasers grown on <100> substrates

Emission of coherent light at 5.1 /spl mu/m wavelength from GaAs-based quantum cascade lasers is reported. This was achieved by integrating nonlinear cascades with large second-order susceptibility in the active regions of the laser.     

Design and practical implementation of multifrequency RF front ends using direct RF sampling

The use of direct RF sampling has been explored as a means of designing multifrequency RF front ends. Such front ends will be useful to multifrequency RF applications such as global navigation satellite system receivers that use global positioning system (GPS) L1, L2, and L5 signals and Galileo signals. The design of a practical multifrequency direct RF sampling front end is dependent on having an analog-to-digital converter whose input bandwidth accommodates the highest carrier frequency and whose maximum sampling frequency is more than twice the cumulative bandwidth about the multiple carrier signals. The principle of direct RF sampling is used to alias all frequency bands of interest onto portions of the Nyquist bandwidth that do not overlap. This paper presents a new algorithm that finds the minimum sampling frequency that avoids overlap. This design approach requires a multifrequency bandpass filter for the frequency bands of interest. A prototype front end has been designed, built, and tested. It receives a GPS coarse/acquisition code at the L1 frequency and GPS antispoofing precision code at both L1 and L2. Dual-frequency signals with received carrier-to-noise ratios in excess of 52 dB-Hz have been acquired and tracked using this system.     

The effect of plastic deformation on Al2CuLi (T 1) precipitation

The enhancement ofT ₁ precipitation in Al-Li-Cu alloys by plastic deformation prior to aging (that is, cold work) and the subsequent increase in alloy strength is investigated. The increased understanding of the role of matrix dislocations in the nucleation and growth ofT ₁ plates, discussed in the previous paper,^[1] permits a detailed study of the phenomenon. In this paper, the effect of different levels of plastic strain on theT ₁ particle distributions as a function of aging time at 190 °C is quantified, and the subsequent influence on tensile properties is thereby described. The effect of plastic deformation is shown to decrease theT ₁ plate length and thickness, increase the number density by almost two orders of magnitude, increase the yield strength by 100 MPa, while simultaneously reaching peak strength in 20 pct of the time required without plastic deformation. Formerly Graduate Student, Department of Materials Science, University of Virginia,     

Construction and performance of a multiparameter focal plane detector for use on a QMG/2 magnetic spectrometer

The design, construction and performance of a modular, two pressure focal plane detector, 550 mm long, 1000 mm deep and with an active height of 60 mm are described. The detector has been operated with ions ranging from 50 MeV ¹H to 200 MeV ³⁶S. Typical results achieved are 0.5 mm and 0.3° for the spatial and angular resolutions, and 0.7% and 3% for the total energy and energy loss measurements. A height signal is also provided.     

Untersuchungen zum Korrosionsverhalten von AlLi-Legierungen

Corrosion behaviour of aluminium-lithium alloys The AlLiMgCu alloy 8090 was studied in its texturated fine grained version “A” and in its recrystallized coarse grain structured version “C” in different artificially aged conditions in reference to several other AlLi alloys, each in its heat treatment condition of practical interest, and to the convetional alloy 2024 T3. The subject of research was the general corrosion behaviour of semifinished AlLi products, particularly sheet material, under alternate and permanent immersion conditions in neutral 3.5% sodium chloride solution; the stress corrosion behaviour was studied under constant load in the long transverse direction according to ASTM G44 and G49. The underaged conditions, which are the relevant conditions for technical application of the 8090 “A” and “C” sheets, showed an approximately equivalent or even better corrosion behaviour in comparison to the lithium-free alloy 2024 T3 in the corrosion tests with unloaded specimens. The threshold above which the AlLi alloy 8090 in some heat treatment conditions is attacked by stress corrosion cracking within the 30 days lasting constant load test depends on alloy composition, testing direction, grain size, stretch-forming, artificial ageing condition, surface pretreatment and the specimens' dimensions.     

The effect of temperature on crazing mechanisms in polystyrene

At room temperature scission is the dominant mechanism for the modification of the entanglement network required for craze formation in polystyrene, but as the temperature is increased towardsT _g, there is the possibility that disentanglement processes may contribute. These will be most important for short chains. If disentanglement can occur, a molecular weight dependence of the crazing stress as a function of temperature will result. This prediction is tested by straining thin films of a range of monodisperse samples of polystyrene at temperatures between 40 and 90° C. The nature of the ensuing deformation has been characterized by transmission electron microscopy. It is observed that whereas only crazing occurs over the entire temperature range for the lowest molecular weight sample, shear processes become important for higher molecular weight materials. For the longest chains, crazing is almost entirely suppressed at 80° C, with the preferential formation of shear deformation zones occurring. These observations are consistent with the idea that disentanglement is playing a significant role in craze formation at sufficiently high temperatures.     

Electrochemical Faceting of polycrystalline platinum in HF solutions

The electrochemical faceting of polycrystalline (pc) platinum yielding a (100)-preferred oriented electrode surface was accomplished in HF solutions by applying to the pc platinum electrode a square wave potential perturbation at 1 kHz in the 0.2 to 1.3 V range (vs rhe). SEM patterns of the resulting surfaces were also obtained. For HF concentrations up to 2 M no appreciable influence of the electrolyte concentration on the electrochemical faceting was noticed. Otherwise, the voltammetric response of the (100)-type preferred oriented platinum surface in the H-adatom potential range when compared to previously reported data resulted remarkably sensitive to the electrolyte composition. The discussion of results was based on the non-equilibrium adsorption conditions for anions under the periodic perturbation.