Standby power system VRLA battery reserve life estimation scheme

This paper presents a valve-regulated lead acid (VRLA) battery reserve life estimation scheme. The scheme is adaptive in both type and frequency of involvement. The scheme is based on capacity trending with the support of a number of state-of-health (SOH) indicators. These SOH indicators include accumulated thermal stress, float voltage, and indicators acquired from the start-of-discharge (coup de fouet) region. An implementation test case is given, indicating that the scheme is capable of providing an accurate estimation of reserve life long before the end of life. Furthermore, the estimation accuracy improves as the end of battery life approaches.     

Organic matter release in low temperature thermal treatment of biological sludge for reduction of excess sludge production.

Thermal treatment applied in association with a biological system allows for a significant reduction in excess sludge production (approximately 50%). In general, heat treatment is described as a sludge disintegration technique. This paper offers a thorough study on the impact of heat treatment, at temperatures below 100 degrees C, on the solubilisation of the sludge COD and its biodegradability. Discontinuous heating experiments were performed on activated and digested sludge. At all temperatures tested the released COD for digested sludge was systematically higher than that for activated sludge (15 and 40%, respectively, at 95 degrees C for 40 min of contact time). For the first 30 min, a 1st order kinetic, with respect to the residual COD, was systematically found. In the range of 40-95 degrees C, digested sludge had a lower activation energy than activated sludge (26 kcal/mol compared to 70-160 kcal/mol). COD solubilisation is thus more positively influenced by temperature in the case of activated sludge. This may be due to the significant difference in the ratio of protein/carbohydrate in digested and activated sludge (1-5 and 0.2-0.7, respectively). The increase in the COD/TKN ratio in the solubilised fraction after thermal treatment of activated sludge suggests a preferential solubilisation of proteins over carbohydrates. Respirometric tests performed on the solubilised COD showed that whatever the sludge origin, only 40-50% of released COD is biodegradable at a conventional hydraulic retention time (i.e., 24 h). Hence, heat treatment would act more through organic matter solubilisation rather than by a biodegradability increase.     

Entropy of multidimensional cellular automata

Since the topological entropy of a vast class of two-dimensional cellular automata (CA) is infinite, of interest is the possibility to renormalize it so that to obtain a positive finite value. We find the asymptotics of the information function of a multidimensional CA and, accordingly, introduce the renormalized topological entropy as a coefficient of this asymptotics. We describe some properties of the introduced quantity, in particular, its positivity for CA of the type of “The Game of Life.” Also, we give an example of an explicit evaluation of this parameter for a particular cellular automaton.     

A prototype of a superconducting magnet for a 170-GHz gyrotron

Within the framework of the “International Thermonuclear Experimental Reactor” (ITER) program, a prototype of a superconducting magnet for a 170-GHz gyrotron has been developed, manufactured, and tested. The operating induction value (7.1 T at the center of a 219-mm-diameter cold hole and 8.1 T on the winding) is reached at a current of 185.2 A. In the final version of the magnet, the required induction value was reached without aging. Special requirements are imposed on the distribution of the magnetic field along the axis, including an abrupt field decrease on both sides of the magnet. Axial forces are additionally taken by a special device. The magnet’s sections are wound with multifiber conductors based on niobium-tin and niobium-titanium alloys. Seventeen resistive shunts are provided for protecting sections during their transition to the normal state. The magnet is equipped with a device for removing a part of energy from the sections. Mechanical stresses in the magnet’s sections and the structure’s power elements have been measured during tests.     

A device for measuring the equivalent resistance of an energized circuit section

A device for measuring the active resistance of a direct current energized circuit section is described. Owing to the use of up-to-date electronic components, an iteration measurement algorithm, and a sinusoidal signal as a test one, the following performance characteristics have been obtained: the measurement time is <1 s, and the error varies from 0.3 to 2.0% in a 100-Ω to 1-MΩ range and ≤25% in 10-to 100-Ω and 1-to 10-MΩ ranges.     

Miniature in vivo robots for remote and harsh environments

Long-term human space exploration will require contingencies for emergency medical procedures including some capability to perform surgery. The ability to perform minimally invasive surgery (MIS) would be an important capability. The use of small incisions reduces surgical risk, but also eliminates the ability of the surgeon to view and touch the surgical environment directly. Robotic surgery, or telerobotic surgery, may provide emergency surgical care in remote or harsh environments such as space flight, or extremely forward environments such as battlefields. However, because current surgical robots are large and require extensive support personnel, their implementation has remained limited in forward environments, and they would be difficult, or impossible, to use in space flight or on battlefields. This paper presents experimental analysis of miniature fixed-base and mobile in vivo robots to support MIS surgery in remote and harsh environments. The objective is to develop wireless imaging and task-assisting robots that can be placed inside the abdominal cavity during surgery. Such robots will provide surgical task assistance and enable an on-site or remote surgeon to view the surgical environment from multiple angles. This approach is applicable to long-duration space flight, battlefield situations, and for traditional medical centers and other remote surgical locations.     

Diffraction of electromagnetic waves by the boundary of a semi-infinite metamaterial

Diffraction of plane waves at the interface of two semi-infinite regions is considered for the case when one of the regions is filled with a metamaterial in the form of a 3D periodic lattice of dipole-type particles. The diffraction problem is solved via the method of compensating sources, which is extended to the case of 3D structures. Different formulations of the diffraction problem that is reduced to either a system of Wiener-Hopf functional equations or a system of linear algebraic equations are presented. Representation of a semi-infinite structure by a sequence of layers characterized by wave transmission matrices is analyzed. It is shown that such matrices can be used to obtain the solution to the diffraction problem in an explicit form.     

Effect of ultrasonic treatment on photoelectric and luminescent properties of ZnSe crystals

The results of the effect of ultrasonic treatment of ZnSe crystals on the structure of the energy spectrum of electronic states of centers with deep levels forming photoelectric and luminescent properties of this compound are presented. It is for the first time proved experimentally that the climb of edge dislocations under the effect of ultrasound leads to regrouping and generation of defects forming deep levels, which manifest themselves in phenomena of photosensitivity and radiative recombination.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Effective factors on synthesis of the hematite–silica red inclusion pigment

The work focuses on the synthesis of a red ceramic pigment by inclusion of hematite in a fumed silica matrix with different specific surface areas. Iron(II) sulfate was used as hematite precursor. Mixtures of iron(II) sulfate and fumed silica with different mole ratios were heated at different temperatures from 1000 to 1300 °C for 4 h.