The effect of some alloying elements on the corrosion resistance of lead-antimony alloys — II. Silver

The effect of Ag on the stationary and non-stationary anodic corrosion rates of PbSbCd and PbSb alloys in H₂SO₄ has been studied. Anodic polarization curves were constructed under galvanostatic and potentiostatic conditions. Optical microscopic examination and microprobe analysis of the alloys were conducted. The beneficial effect of Ag was ascribed to a delay in closure of pores in the initial PbSO₄ film. The leaching out of Sb from the outermost layers and the simultaneous nucleation of PbSO₄ and Ag₂SO₄ from supersaturated solutions in the pores is thus made possible.     

The Hygroscopicity of Moisture Barrier Film Coatings

ABSTRACT

The hygroscopicity of three commercial moisture-barrier film coatings, namely, Eudragit L30 D-55 (methacrylic acid–ethyl acrylate copolymer), Opadry AMB (polyvinyl alcohol based system), and Sepifilm LP 014 (hypromellose, microcrystalline cellulose, and stearic acid based formulation), was investigated using a dynamic vapor sorption apparatus. Moisture uptake by cast films and uncoated and coated tablet cores, which were designed to be hygroscopic, low hygroscopic, and waxy, was measured following exposure to repeat relative humidity (RH) cycles of 0-50-0-50-0%, 0-75-0-75-0%, and 0-90-0-90-0% RH at 25°C. Eudragit cast film exhibited the fastest equilibration but was also the least hygroscopic. Sepifilm had the fastest sorption and took up the greatest mass of water. The rate of uptake for Opadry film was similar to Sepifilm. However, this film continued to sorb moisture for a longer period. When returned to 0% RH it retained moisture in the film showing that it had a high affinity for moisture within the film. The data for the different cores indicated that there was very little benefit in using a moisture barrier film on cores with low hygroscopicity, the mass gain being a sum of that which would be expected to sorb to the film and that which sorbs to the uncoated core. There was, however, some advantage for hygroscopic cores where, even though the barrier coatings allowed substantial water sorption into the core, the extent of this was less and the rate of uptake lower than for the uncoated sample.     

Low loss Sr1−xCaxLa4Ti5O17 microwave dielectric ceramics

Microwave dielectric ceramics in the Sr_1−xCa_xLa₄Ti₅O₁₇ (0 ≤ x ≤ 1) composition series were prepared through a solid state mixed oxide route. All the compositions formed single phase ceramics within the detection limit of in-house X-ray diffraction when sintered in the temperature range 1450-1580 °C. Theoretical density and molar volume decreased due to the substitution of Ca²⁺ for Sr²⁺ which was associated with a decrease in the dielectric constant (?_r) and temperature coefficient of resonant frequency (τ_f) but an increase in quality factor, Qf_o. Optimum properties were achieved for Sr_0.4Ca_0.6La₄Ti₅O₁₇ which exhibited, ?_r ∼ 53.7, Qf_o ∼ 11,532 GHz and τ_f ∼ −1.4 ppm/°C.     

Non-linear radiation effects on magnetic/non-magnetic nanoparticles with different base fluids over a flat plate

This work investigates the two-dimensional steady convective boundary layer flow and heat transfer of Newtonian/non-Newtonian base fluids with magnetic/non-magnetic nanoparticles over a flat plate which incorporates non-linear thermal radiation and slip effects. We considered magnetite and aluminium oxide as magnetic and non-magnetic nanoparticles suspending inside the two sorts of base fluids specifically Water and Sodium Alginate. For physical significance we analyzed the behavior on non-Newtonian profiles by employing Casson model individually. The particular intrigue lies in looking the impacts of non-linear thermal radiation on the behavior of the flow. The solution of wide class of boundary value problems are facilitated by the change of the partial differential equations administering the flow utilizing similarity transformations into ordinary differential equations. The ODE’s are numerically handled by applying fourth order Runge-Kutta integration scheme in association with shooting procedure. The novel results for the dimensionless velocity and temperature inside the boundary layer are exhibited graphically for various parameters that describe the flow. A graphical demonstration is given for the skin friction coefficient and the local Nusselt number.     

Transfer Learning-based Computer-aided Diagnosis System for Predicting Grades of Diabetic Retinopathy

Diabetic retinopathy (DR) diagnosis through digital fundus images requires clinical experts to recognize the presence and importance of many intricate features. This task is very difficult for ophthalmologists and time-consuming. Therefore, many computer-aided diagnosis (CAD) systems were developed to automate this screening process of DR. In this paper, a CAD-DR system is proposed based on preprocessing and a pre-train transfer learning-based convolutional neural network (PCNN) to recognize the five stages of DR through retinal fundus images. To develop this CAD-DR system, a preprocessing step is performed in a perceptual-oriented color space to enhance the DR-related lesions and then a standard pre-train PCNN model is improved to get high classification results. The architecture of the PCNN model is based on three main phases. Firstly, the training process of the proposed PCNN is accomplished by using the expected gradient length (EGL) to decrease the image labeling efforts during the training of the CNN model. Secondly, the most informative patches and images were automatically selected using a few pieces of training labeled samples. Thirdly, the PCNN method generated useful masks for prognostication and identified regions of interest. Fourthly, the DR-related lesions involved in the classification task such as micro-aneurysms, hemorrhages, and exudates were detected and then used for recognition of DR. The PCNN model is pre-trained using a high-end graphical processor unit (GPU) on the publicly available Kaggle benchmark. The obtained results demonstrate that the CAD-DR system outperforms compared to other state-of-the-art in terms of sensitivity (SE), specificity (SP), and accuracy (ACC). On the test set of 30,000 images, the CAD-DR system achieved an average SE of 93.20%, SP of 96.10%, and ACC of 98%. This result indicates that the proposed CAD-DR system is appropriate for the screening of the severity-level of DR.     

Enhancement in Physical Properties of Silver-Doped Fe–Ni Invar Nano-alloy Using Chemical Reduction Method

Journal of Superconductivity and Novel Magnetism - Silver-substituted Fe–Ni nano invar alloy is a new and innovative field of research due to their interesting invar, magnetic and electrical...     

Least-Square Collaborative Beamforming Linear Array for Steering Capability in Green Wireless Sensor Networks

This paper presents a collaborative beamforming (CB) technique to organize the sensor node's location in a linear array for green wireless sensor network (WSN) applications. In this method, only selected clusters and active CB nodes are needed each time to perform CB in WSNs. The proposed least-square linear array (LSLA) manages to select nodes to perform as a linear antenna array (LAA), which is similar to and as outstanding as the conventional uniform linear array (ULA). The LSLA technique is also able to solve positioning error problems that exist in the random nodes deployment. The beampattern fluctuations have been analyzed due to the random positions of sensor nodes. Performances in terms of normalized power gains are given. It is demonstrated by a simulation that the proposed technique gives similar performances to the conventional ULA and at the same time exhibits lower complexity.     

Neutron radiation effects on metal oxide semiconductor (MOS) devices

The main purpose of this study is to provide the knowledge and data on Deuterium-Tritium (D-T) fusion neutron induced damage in MOS devices. Silicon metal oxide semiconductor (MOS) devices are currently the cornerstone of the modern microelectronics industry. However, when a MOS device is exposed to a flux of energetic radiation or particles, the resulting effects from this radiation can cause several degradation of the device performance and of its operating life. The part of MOS structure (metal oxide semiconductor) most sensitive to neutron radiation is the oxide insulating layer (SiO₂). When ionizing radiation passes through the oxide, the energy deposited creates electron-hole pairs. These electron-hole pairs have been seriously hazardous to the performance of these electronic components. The degradation of the current gain of the dual n-channel depletion mode MOS caused by neutron displacement defects, was measured using in situ method during neutron irradiation. The average degradation of the gain of the current is about 35 mA, and the change in channel current gain increased proportionally with neutron fluence. The total fusion neutron displacement damage was found to be 4.8 × 10⁻²¹ dpa per n/cm², while the average fraction of damage in the crystal of silicon was found to be 1.24 × 10⁻¹². All the MOS devices tested were found to be controllable after neutron irradiation and no permanent damage was caused by neutron fluence irradiation below 10¹⁰n/cm². The calculation results shows that (n,α) reaction induced soft-error cross-section about 8.7 × 10⁻¹⁴ cm², and for recoil atoms about 2.9 × 10⁻¹⁵ cm², respectively.     

Interaction Between Two Mutually Orthogonal Heat-Generating Baffles in a Square Cavity

Laminar free convection induced by two mutually orthogonal discrete heat-generating baffles in a two-dimensional square cavity is analyzed numerically. The computations were carried out for different locations and combinations of heat source strengths of the baffles for a fixed Grashof number of 10⁶and Prandtl number of 0.71. The coupled governing equations were solved bya finite-difference method using alternating direction implicit technique and successive overrelaxation methods. The obtained results clearly show that the hydrodynamic and thermal fields in the cavity depend on both the location and strength of the heat-generating baffles. Though the flow inhibition is caused by both the baffles, the baffle with higher source strength plays a decisive role in inducing the flow. The locations of baffles with unequal source strengths produce significant changes in the net heat transfer rate. This is further magnified for higher contrast in source strengths. This study provides qualitative suggestions that may improve the thermal design of sealed enclosures, which are encountered frequently in the electronics industry.     

Multi‐agent‐based sharing power economy for a smart community

In this paper, a multi‐agent‐based locally administrated power distribution hub (PDH) for social welfare is proposed that optimizes energy consumption, allocation, and management of battery energy storage systems (ESSs) for a smart community. Initially, formulation regarding optimum selection of a power storage system for a home (in terms of storage capacity) is presented. Afterwards, the concept of sharing economy is inducted in the community by demonstrating PDH. PDH is composed of multiple small‐scale battery ESSs (each owned by community users), which are connected together to form a unified‐ESS. Proposed PDH offers a localized switching mechanism that takes decision of whether to buy electricity from utility or use unified‐ESS. This decision is based on the price of electricity at ‘time of use’ and ‘state of charge’ of unified‐ESS. In response to power use or share, electricity bills are created for individual smart homes by incrementing or decrementing respective submeters. There is no buying or selling of power from PDH; there is power sharing with the concept of ‘no profit, no loss’. The objective of the proposed PDH is to limit the purchase of electricity on ‘high priced’ hours from the utility. This not only benefits the utility at crucial hours but also provides effective use of power at the demand side. The proposed multi‐agent system depicts the concept of sharing power economy within a community. Finally, the proposed model is analyzed analytically, considering on‐peak, off‐peak, and mid‐level (mid‐peak) prices of a real‐time price signal during 24 h of a day. Results clearly show vital financial benefits of ‘sharing power economy’ for end users and efficient use of power within the smart community. Copyright © 2017 John Wiley & Sons, Ltd.