Development of method to improve efficiency of residual current device under 1000 V on excavators of mining enterprises

This article presents the results of experimental studies on a coal mine. According to the results, the current of single phase-to-earth fault in the network under 1000 V has a value less than the current of the residual current device set point. This article presents a method aimed to improving the efficiency of the residual current device used on excavators and drill-rings at mining enterprises. Indeed, the method developed to improve the efficiency of residual current devices under 1000 V is based on setting up a direct current into three-phase mains with a fixed set-point of protection against any phase-to-ground insulation damage, where electric equipment is switched off due to increases of capacitance between a conductor and earth when live-line bare-hand touching of electric equipment occurs.     

The Effects of Annealing After Equal Channel Angular Extrusion (ECAE) on Mechanical and Magnetic Properties of 49Fe-49Co-2V Alloy

Metallurgical and Materials Transactions A - Equal channel angular extrusion (ECAE) of 49Fe-49Co-2V, also known as Hiperco® 50A or Permendur-2V, greatly improves the strength and ductility of...     

High Temperature Oxidation Behavior of Conventional and Nb-Modified MAR-M246 Ni-Based Superalloy

The present investigations focused on the thermal oxidation of two variants of MAR-M246 alloy having the same contents of Ta and Nb in at. pct, considering the effects of total replacement of Ta by Nb. The alloys were produced by investment casting using high purity elements in induction furnace under vacuum atmosphere. The alloys were oxidized pseudo-isothermally at 800 °C, 900 °C and 1000 °C up to 1000 hours under lab air. Protective oxidation products growing on the surface of the oxidized samples were mainly Al₂O₃, Cr₂O₃. Other less protective oxide such as spinels (NiCr₂O₄ and CoCr₂O₄) and TiO₂ were also detected as oxidation products. The conventional alloy exhibited slight internal oxidation at 800 °C and an enhanced resistance at 900 °C and 1000 °C. The Nb-modified alloy presented an exacerbated internal oxidation and nitridation at 900 °C and 1000 °C and an enhanced resistance at 800 °C. At 1000 °C, Nb-modified alloy was particularly affected by excessive spalling as the main damage mechanisms. From a kinetic point of view, both alloys exhibit the same behavior at 800 °C and 900 °C, with k_p values typical of alumina forming alloys (2 × 10⁻¹⁴ to 3.6 × 10⁻¹³ g² cm⁻⁴ s⁻¹). However, Ta modified alloys exhibited superior oxidation resistance at 1000 °C when compared to the Nb modified alloy due to better adherence of the protective oxide scale.

     

Recycling of Nickel-Slag Tailings into Liquid Products: A Case Study using Slag from the Southern Urals Nickel Plant

Metallurgist - We provide an overview of the current status of research on reprocessing of nickel waste tailings, describe the current condition of the tailings, and set forth an important economic...     

Microstructural Features of Low-Alloy Pipeline Steels that Determine Impact Strength of Welded Joint Heat-Affected Zone

Metallurgist - Microstructural mechanisms reducing the impact strength values of a coarse grained heat-affected zone are studied for two K60 microalloyed steels. Research is conducted on specimens...     

Sintering and Briquetting Synergy in Blast Furnace Smelting

Metallurgist - The article describes the concept of partially replacing the sinter in a blast furnace charge with extrusion briquettes to form the basis for sintering and briquetting synergy. The...     

Power Supply at Metallurgical Iron-and-Steel Works: Features and Development Prospects

Metallurgist - The article provides a brief assessment of the current state of power supply units at metallurgical plants and prospects for their future development. The principal power-supply...     

Remelting of Iron Shavings with the Synergistic Effect of Minimum Metal Loss

Metallurgist - The well-known technologies of remelting iron shavings lead to significant (30%) losses of metal. An electroslag smelting furnace with graphite electrodes is proposed for remelting...     

Combustion in Ni–Al System with Cu Additive (Powder or Rod). Experiment and Mathematical Model

Russian Journal of Non-Ferrous Metals - Experimental studies have been carried out with theoretical calculations of wave synthesis in the Ni–Al–Cu system using a mathematical model....     

Ensuring Strength in Laser Welds Made Using the Dispersion-Hardened EP693 Nickel Alloy

Russian Journal of Non-Ferrous Metals - The process of making a weld using the heat-resistant EP693 alloy (Ni–Cr–W–Co–Co–Mo system) to make assemblies and components...