Extraction equilibrium conditions of beryllium and aluminium from a beryl ore for optimal industrial beryllium compound production

This study examines the extraction of beryllium and aluminium from a Nigerian beryl ore using Cyanex®272 in kerosene from an aqueous sulphate pregnant solution. Parameters such as extractant concentration and equilibrium pH that dictates the extraction yield were studied. Under the following conditions: temperature 27?±?2°C, phase ratio 1?1, about 45.50 and 46.76% of beryllium and aluminium were extracted by 0.15?mol?L^?1 Cyanex®272 concentration within 30?min. However, the extraction yield of beryllium and aluminium was increased to 91.68% and 97.89% at equilibrium pH of 3 and 4, respectively, for beryllium and aluminium at 27?±?2°C. A 0.05?mol?L^?1 H₂SO₄ solution was found to be adequate for the stripping of about 99.00% Be and 95.40% Al from the loaded organic phase. The pure solutions containing metal ions were accordingly beneficiated to obtain beryllium and aluminium compounds of industrial values.     

Genesis of nanocrystalline Ho2O3 via thermal decomposition of holmium acetate: Structure evolution and electrical conductivity properties

This study focuses on the preparation of nanostructured holmium oxide via the decomposition of holmium acetate precursor utilizing the non-isothermal strategy. Thermogravimetric analysis(TGA) was used to follow up the various thermal events involved in the decomposition process. Dehydration completes approximately at 150℃, which is followed by the decomposition of the anhydrous acetate leading to the formation of holmium oxide. Based on the TGA results the acetate precursor was heated non-isothermally at the temperature range of 150 e700℃. The obtained solids were characterized using powder X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS), Fourier transform infrared spectroscopy(FT-IR), field-emission scanning electron microscopy(FE-SEM) and transmission electron microscopy(TEM). It is found that nanocrystalline Ho_2 O_3 starts to form at 500℃ and presents the only phase detected at the 500 e700℃ range. The electrical conductivity of the solids that form at the temperature range of 300 e700℃ was investigated. The obtained values were correlated with the observed structural modifications accompanying the heat treatment. The electrical conductivity of the Ho_2 O_3 samples prepared at 500, 600 and 700℃ reaches the values of 1.92 × 10~(-7), 1.61 × 10~(-7) and 8.33 × 10~(-8) Ω~(-1)cm~(-1) at a measuring temperature of 500℃, respectively. These values are potentially advantageous for high-resistivity devices.     

Magnetron sputtered Dy_2O_3 with chromium and copper contents for antireflective thin films with enhanced absorption

Dy_2O_3 is a rare earth oxide having a number of advanced applications in various fields including protective or antireflective coatings, Main objective of this novel research work is to check the effect of Cr and Cu addition on different properties of Dy_2O_3 and achievement of antireflective thin films with enhanced abso rption. Thin films of these materials we re deposited using DC magnetron with reactive cosputtering. XRD studies reveals the crystalline nature of thin films having Dy_2O_3(222) reflection in all samples with Cr_2O_3(116) and CuO(111) reflections in Cr and Cu containing compositions. Field emission scanning electron microscopy demonstrates the homogeneous deposition of thin films with uniform shape, size and distribution of grains. Refractive index, extinction coefficient and absorption coefficient significantly increase while optical reflectance decreases with Cr and Cu mediation corroborating an improved antireflective mechanism. The imaginary part of dielectric constant is found to increase slightly with low tangent loss for Cr containing composition co nsidered favorable for energy storage applications.     

Polyvinylidene fluoride and polyetherimide hollow fiber membranes for CO2 stripping in membrane contactor

Porous polyvinylidene fluoride (PVDF) and polyetherimide (PEI) hollow fiber membranes incorporating polyethylene glycol (PEG) were prepared via spinning process for CO₂ membrane stripping. CO₂ loaded diethanolamine solution was used as liquid absorbent while N₂ was used as a strip gas. The characterization study of the fibers was carried out in terms of permeation test, contact angle measurement and liquid entry pressure (wetting pressure). Performance study via membrane contactor stripping was carried out at specific operating condition. The experimental results showed that PVDF membrane have high gas permeation, effective surface porosity and contact angle despite having lower liquid entry pressure in comparison with PEI membrane. PVDF-PEG membrane showed the highest stripping flux of 4.0 × 10⁻² mol m⁻² s⁻¹ at 0.7 ms⁻¹ compared to that of PEI membrane. Although the stripping flux for PEI-PEG membranes was slightly lower than PVDF membrane (e.g. 3.5 × 10⁻² mol m⁻² s⁻¹ at liquid velocity of 0.85 ms⁻¹), the membrane wetting pressure of PEI membrane is higher than hydrophobic PVDF membrane. Long term performance of both membranes showed severe flux reduction but started to level-off after 30 h of operation.     

确保粮食安全和环境可持续发展的水土资源利用

主要讨论灌溉农业所面临的挑战.随着人均可用水量的不断下降,灌溉农业必须提高水资源利用效率,同时进一步采用有利于环境的经营和管理方式.灌溉界面临的压力是如何通过提高作物产量和用水效率来实现生产率的最大化.今后的发展方向是以更加高效率、有成效的方式利用水资源,而实现从"提高每滴水的粮食产量"向"少用水,多产粮"的转变,则有助于该目标的实现.为了尽可能减小外在因素的影响,将来的努力方向是在全面性和整体性上下工夫.     

Selection of the optimum decomposition level using the discrete wavelet transform for automobile suspension system

Journal of Mechanical Science and Technology - This paper discusses the determination of the optimum decomposition level by using the discrete wavelet transform (DWT) method for an automobile...     

TRANSPORT PROPERTIES OF CELLULAR FOOD MATERIALS UNDERGOING FREEZE-DRYING

The samples of sliced and mashed apples were freeze-dried by controlling their surface temperatures over the usual pressure range of commercial operations. The surface of sliced samples could not be maintained at above 10°C in order to prevent the frozen layer from melting, while that of mashed samples was allowed to heat up to 70°C.

Thermal conductivities and permeabilities were determined by applying the uniformly-retreating-ice front model to the dried layer of the samples undergoing freeze-drying. The values of permeability for the mashed samples were found to depend on the ice-crystallization time during freezing. The results indicated that the drying rate of sliced samples was limited by the transfer rate of water vapor flowing through the dried layer. A cellular structural model is proposed for predicting the permeability of the dried layer, based on the resistance of the cell membrane to molecular transfer of water vapor.     

Chemical Profile and Biological Activities of Two Edible Plants: Chemical Investigation and Quantitative Analysis Using Liquid Chromatography Tandem Mass Spectrometry and Gas Chromatography Mass Spectrometry

The objectives of this study were to define the phenolic and fatty acid profiles, anticholinesterase, antioxidant, antimicrobial activities, and total phenolic-flavonoid contents of Lycopsis orientalis and Tragopogon latifolius var. angustifolius which have been used as food source and food supplement in Anatolia and have never been examined before. Rosmarinic and quinic acids (21.11 and 11.46 mg g^–1 extract, respectively) were found to be the most abundant constituents in L. orientalis and T. latifolius var. angustifolius among the studied 27 compounds by liquid chromatography tandem mass spectrometry. In the fatty acid compositions of L. orientalis and T. latifolius var. angustifolius that were determined by gas chromatography mass spectrometry, oleic (29.1%) and palmitic (28.7%) acids were identified as the major components, respectively. The high antioxidant activity of the methanol extract of L. orientalis shows parallelism to its rosmarinic acid content. Besides, this extract showed medium anticholinesterase activity. The results of the present study proves that the L. orientalis might also be used as a food source due to its high phenolic acid content and strong antioxidant property.     

Constrained model predictive control of proton exchange membrane fuel cell

A constrained model predictive control (MPC) is designed to regulate the air flow rate of proton exchange membrane fuel cell (PEMFC). Oxygen excess ratio, compressor flow rate and supply manifold pressure are constrained to avoid oxygen starvation, surge and choke phenomena. This is achieved by manipulating compressor voltage and stack current. The choice of the manipulated input to satisfy a constraint is investigated. Surge and choke avoidance is successful, when compressor voltage is manipulated. When stack current is utilized to satisfy surge and choke constraints, a large unrealistic current is needed. Oxygen starvation is successfully avoided utilizing stack current, while compressor voltage manipulation fails to prevent oxygen starvation. Thus, a current governor is implemented to handle oxygen starvation, while the compressor voltage is constrained to avoid surge and choke. Quadratic programming optimization, Laguerre and exponential weight function are employed to reduce the computational burden of the controller. The simulation results prove that the proposed controller managed to satisfy all constraints without any conflict.