Organizing the production of heat-insulating inserts for ingot-mold hot tops

The Zlatoust Metallurgical Plant has developed a technology that employs semi-dry pressing to make two-layer (composite) heat-insulating inserts for ingot-mold hot tops. The working layer is made of a mixture of materials based on quartz sand, while the insulating layer is based on foamed vermiculate. The binders are sodium silicate solution and commercial lignosulfonate with a density of 1.12–1.20 g/cm³.     

Enhancement of heat and mass transfer in a plane channel with turbulizers on one of the walls

The effect of turbulizing asperities positioned on one of the walls of a plane channel on the intensity of exchange processes near a smooth wall with injection of different working media is studied experimentally. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 70, No. 3, pp. 404–408, 1997.     

Mikrotechnik für Raumfahrtanwendungen

This contribution describes the preparation, based upon a chemically amplified novolak resist (CAR), electron beam lithography, and ECR plasma etching, of structures with a high aspect ratio (10∶1) and lateral dimensions in the sub-micrometer range (150nm–300nm) which may serve as collector surfaces for sub-μm dust particles in a space experiment.     

On the universal behavior of scattering from a rough surface forsmall grazing angles

It is shown that for scattering from a plane of an average rough surface, the scattering cross section of the range of small grazing angles of the scattered wave demonstrates a universal behavior. If the angle of incidence is fixed (in general, it should not be small), the diffuse component of the scattering cross section for the Dirichlet problem is proportional to &thetas;² where &thetas; is the (small) angle of elevation and for the Neumann problem it does not depend on &thetas;. For the backscattering case, these dependencies correspondingly become &thetas;⁴ and &thetas;⁰. The result is obtained from the structure of the equations that determine the scattering problem rather than the use of an approximation     

Stochastic complexity measures for physiological signal analysis

Traditional feature extraction methods describe signals in terms of amplitude and frequency. This paper takes a paradigm shift and investigates four stochastic-complexity features. Their advantages are demonstrated on synthetic and physiological signals; the latter recorded during periods of Cheyne-Stokes respiration, anesthesia, sleep, and motor-cortex investigation     

A method for dynamic measurement of the resistance to dry heat exchange by footwear

Five different types of cold protective footwear have been tested with regard to their resistance to dry heat loss (i.e. the insulation) with a new electrically heated foot model. The model is able to simulate 'walking' movements in order to provide a more realistic simulation of wear conditions. Thermal insulation of shoes with and without a steel toe cap was the same. The insulating properties during simulated walking movements were 10-25% lower compared with static conditions. For two of the shoe models a significantly lower insulation value for the sole area was obtained when adding a weight of 30 kg. A significant difference could also be found between the insulation values of two different sizes of one of the models. Measurements with the standard method (EN 344) correlated well with the local insulation value of the sole part of the thermal foot. Correlation with the insulation value for the whole shoe was much less, variation was bigger and ranking in terms of cold protection differed between methods. The electrically heated foot model appears to provide a reproducible, accurate and more realistic method for measuring the insulation properties of shoes than EN 344.     

Calculation of the acoustical characteristics of gas transport equipment of the unit type in the design stage

Translated from Khimicheskoe i Neftyanoe Mashinostroenie, No. 11, pp. 28–30, November, 1993.     

Effect of Bi and Sr concentrations on the formation of the 2223 phase in Bi-Pb-Sb-Sr-Ca-Cu-O materials, obtained under different conditions of thermal treatment

The superconducting properties and the phase and chemical composition of Bi _x Pb_0.3Sb_0.1Sr _y Ca₂Cu₃O_z (x=1.5, 1.6, and 1.7;y=1.9, 2.0, and 2.1) materials synthesized by one-step and multistep thermal treatments have been investigated. The multistep annealing between 825–875°C promotes the 2223 phase. The change of Bi concentration has little effect on the 2223 phase formation, regardless of the kind of thermal treatment used, but increasing the Sr concentration (y> 2) strongly inhibits this phase. It has also been established that the loss of Pb after synthesis depends on the initial Bi concentration. The loss of Pb decreases when the initial Bi content is lower.