The time course of plausibility effects on eye movements in reading: Evidence from noun-noun compounds.

Readers' eye movements were monitored as they read sentences containing noun-noun compounds that varied in frequency (e.g., elevator mechanic, mountain lion). The left constituent of the compound was either plausible or implausible as a head noun at the point at which it appeared, whereas the compound as a whole was always plausible. When the head noun analysis of the left constituent was implausible, reading times on this word were inflated, beginning with the first fixation. This finding is consistent with previous demonstrations of very rapid effects of plausibility on eye movements. Compound frequency did not modulate the plausibility effect, and all disruption was resolved by the time readers' eyes moved to the next word. These findings suggest (contra Kennison, 2005) that the parser initially analyzes a singular noun as a head instead of a modifier. In addition, the findings confirm that the very rapid effect of plausibility on eye movements is not due to strategic factors, because in the present experiment, unlike in previous demonstrations, this effect appeared in sentences that were globally plausible. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

Fluctuations of Turbulent Bed Shear Stress

With the assumption that the bed shear stress fluctuates in a lognormal fashion, the probability density function (PDF) of the standardized bed shear stress is derived as a function of the relative shear stress intensity. The PDF is more skewed with larger relative intensities, but approaches a Gaussian function when the relative intensity is small. The computed PDF agrees well with the reported experimental data for flows over a smooth boundary. The higher-order moments of the bed shear stress, skewness, and kurtosis, are shown analytically to be also dependent on the relative intensity. The theoretical dependencies are then compared to a number of measurements available in the literature. The Reynolds number effect on the relative intensity is also discussed.     

Gelling of alginate fibres

Equipment was developed to measure the time for complete gelling of sodium alginate fibres in calcium chloride solution, taken as the time to achieve maximum tensile strength. The effects of fibre diameter, alginate concentration, alginate composition and calcium chloride concentration on gelling time were investigated. A diffusional model, developed to predict the gelling time, agreed with experimental results except for the effect of calcium ion concentration which was modelled empirically.     

Location of Aluminum in Substituted Calcium Silicate Hydrate (C-S-H) Gels as Determined by 29Si and 27Al NMR and EELS

Solid-state ²⁷Al and ²⁹Si magic angle spinning NMR spectroscopy has been combined with electron energy loss spectroscopy carried out in the transmission electron microscope to determine the location of Al substituting in a semicrystalline C-S-H gel present in a hydrated synthetic slag glass. The gel is found to contain mainly pentameric silicate chains in which the central silicon is substituted by aluminum.     

POLARIZATION BEHAVIOR OF PACKED-BED ELECTRODES: A COMPARATIVE STUDY OF EXPERIMENTAL AND MODELING RESULTS

The current distribution and overall polarization behavior of electrodeposition at a flow-through (packed bed or fluidized bed) electrode are modeled by means of a one-dimensional model involving a primary reacting species and a simultaneous side reaction. The model equations are solved by orthogonal collocation; the time and storage requirements compare favorably to those of finite-difference methods. Experimental data obtained using a packed-bed electrode are compared with the model predictions and various methods of fitting the data are compared.     

Asymptotic deformation and stress fields at the tip of a sharp notch in an elastic-plastic material

The singular elastic-plastic stress, strain and the displacement fields at the tip of a sharp notch for both plane stress and plane strain conditions are investigated analytically. The material is assumed to be governed by the deformation theory of plasticity with linear strain hardening characteristic. Since the elastic strain is retained in the analysis, the final strain and displacement fields can be separated into the elastic and the plastic parts. In the case with zero notch angle, the results reduce to the classical crack problem. The relationship of the amplitude of the near crack tip elastic-plastic field to the elastic far field is obtained. Both mode I and mode II cases are investigated. The mixed mode case is also discussed.     

PPTC元件为电子设备提供价廉可靠的端口保护

高分子正温度系数(PPTC)电路保护元件主要是对有破坏性的电流过载冲击进行保护,通常称之为“可恢复式保险丝”。PPTC元件被广泛应用于计算机和外部设备的电路保护,以确保在发生意外连接中断或短路的情况下,不会导致永久性且代价巨大的内部和外部电路受损。这种元件已经成为了I/O(输入/输出)保护的工业标准,广泛应用于USB、IEEE1394、CPU和VGA等方面。在USB和IEEE1394的规范说明中都特别提及这种元件。在计算机工业中,应用PPTC元件较其它类似技术,如一次性保险丝具有更多优点。最主要的是PPTC元件是可恢复式的,减少了由于保…     

DBS电视接收机低中频与直接转换调谐器的比较

CMOS技术是把L波段卫星调谐器、解调器和其它功能整合至低成本、高效能单芯片的关键。本文将探讨新型低中频和传统零中频DBS调谐器架构在单芯片DBS射频前端设计中的优缺点。