Scanning electrochemical microscopy. Hydrodynamics generated by the motion of a scanning tip and its consequences on the tip current

The motion of a SECM tip above a substrate generates a flow of the surrounding fluid. Finite element calculations show that this flow is a simple linear-shear flow (Couette flow) for small tip-substrate separations and deviates from Couette's law at larger ones. The effect of fluid flow on the tip current response was determined numerically. Different mass-transfer regimes are observed depending on the insulating or conducting nature of the substrate, the tip speed (or fluid velocity), and the tip-substrate separation. Those observations are tested experimentally, and good agreement is obtained between numerical and experimental results.     

Relations entre la notion et la perception de la vitesse relative chez l'enfant.

Administered 2 tasks bearing on the perception and concept of relative velocity to 7-, 9-, 11-, and 13-yr-old children (24 at each age level). The perceptual task presented an illusion created by the movement of a target on a moving background, while the conceptual task was a modified version of Piaget's technique. In each task the 2 movements involved were either in the same (MS) or in the opposite direction. It was found that the illusion appeared earlier than the corresponding concept under the MS condition. The possibility of a retroactive effect of the concept on the percept is suggested. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Reliability aspects of gate oxide under ESD pulse stress

Power law time-to-breakdown voltage acceleration is investigated down to ultra-thin oxides (1.1 nm) in the ESD regime in inversion and accumulation. Breakdown modes, oxide degradation and device drifts under ESD-like stress are discussed as function of the oxide thickness. The consequent impacts on the ESD design window are presented.     

Domestic refrigeration practices with emphasis on hygiene: analysis of a survey and consumer recommendations

A Web-enabled survey was conducted to improve knowledge of home refrigeration practices of French consumers (n = 809), with an emphasis on hygiene, and this information was used to establish recommendations. The survey targeted a convenience sample of working people. Analysis of the survey responses revealed that efforts should be directed toward improvement of microbiological control measures. Only 37% of respondents made sure the temperature in their refrigerator was 4 degrees C or below. Only 37% of respondents reported that they systematically wrapped food. Sponges, known to be frequently highly contaminated, were used by 89% of the respondents to clean their refrigerator, which indicates the need to recommend disinfection of sponges before they are used for cleaning. Twenty-seven percent of respondents used sodium hypochlorite (bleach), but it was applied without previous cleaning (21% of the users) or in the commercial concentrated form (7% of the users). The permanent presence of water condensation on the shelves was noted by 2% of respondents, suggesting imperfect closure of the door, with a consequence of higher energy consumption and water available for microbial circulation and growth. Thus, an important recommendation is to check the door gaskets and to ensure the tight closure of the door. Seventy percent of the respondents declared that they never put warm or hot food in the refrigerator. However, many people, when orally questioned, acknowledged that they leave dishes at ambient temperature overnight before putting them in the refrigerator. It therefore is essential to recommend that perishable food not be left for more than 2 h at ambient temperature.     

Robocast zirconia-toughened alumina scaffolds: Processing,structural characterisation and interaction with human primary osteoblasts

Zirconia-toughened alumina (ZTA) is the gold-standard ceramic in hip arthroplasty, but still lacks direct osseointegration and a metal shell, often coated with a bioactive layer, is currently required. The latter could potentially be replaced by a thinner, architectured ZTA layer, thereby allowing for larger acetabular components, with larger range of motion and lower dislocation risk. Robocasting may be an adequate technique to fabricate the architectured layer. Therefore, as a first step, this study aimed to produce ZTA scaffolds (3D-ZTA) by robocasting and assess their in vitro response. Shape retention was achieved by using a stable, well-dispersed, high solid loading ink injected in acid pH waterbath. 3D-ZTA exhibit regularly spaced microporous, rough struts and fully interconnected macroporosity. Human primary osteoblasts were homogenously distributed inside 3D-ZTA and showed increased osteogenic marker expression compared to 2D-ZTA control. Further work will focus on optimizing scaffold design to improve cell retention and extracellular matrix maturation.     

LTL model checking for communicating concurrent programs

Innovations in Systems and Software Engineering - We present in this paper a new approach to the static analysis of concurrent programs with procedures. To this end, we model multi-threaded...     

Poly(lactide)/cellulose nanocrystal nanocomposites by high-shear mixing

There is currently considerable interest in developing stiff, strong, tough, and heat resistant poly(lactide) (PLA) based materials with improved melt elasticity in response to the increasing demand for sustainable plastics. However, simultaneous optimization of stiffness, strength, and toughness is a challenge for any material, and commercial PLA is well-known to be inherently brittle and temperature-sensitive and to show poor melt elasticity. In this study, we report that high-shear mixing with cellulose nanocrystals (CNC) leads to significant improvements in the toughness, heat resistance, and melt elasticity of PLA while further enhancing its already outstanding room temperature stiffness and strength. This is evidenced by (i) one-fold increase in the elastic modulus (6.48 GPa), (ii) 43% increase in the tensile strength (87.1 MPa), (iii) one-fold increase in the strain at break (∼6%), (iv) two-fold increase in the impact strength (44.2 kJ/m²), (v) 113-fold increase in the storage modulus at 90°C (787.8 MPa), and (vi) 10³-fold increase in the melt elasticity at 190°C and 1 rad/s (∼10⁵ Pa) via the addition of 30 wt% CNC. It is hence possible to produce industrially viable, stiff, strong, tough, and heat resistant green materials with improved melt elasticity through high-shear mixing.     

Forest governance and REDD+ in Central Africa: towards a participatory model to increase stakeholder involvement in carbon markets

Forests play a significant role in the global carbon budget, and can help to mitigate climate change impacts. Tropical forests which experience high rates of deforestation and forest degradation are particularly important, as they are the most active in winter. Based on academic research into global environmental policies in Central Africa, this study finds that REDD+ policies can succeed when there is a carbon market mechanism that increases participation by developing countries, with better integration of forest management and community forestry. Incentives should be based on an appropriate baseline, accurate carbon stocks and fluxes estimation, a suitable silvicultural system and regular monitoring.     

A Review of Digital Terrain Modeling

Terrains are a crucial component of three‐dimensional scenes and are present in many Computer Graphics applications. Terrain modeling methods focus on capturing landforms in all their intricate detail, including eroded valleys arising from the interplay of varied phenomena, dendritic mountain ranges, and complex river networks. Set against this visual complexity is the need for user control over terrain features, without which designers are unable to adequately express their artistic intent. This article provides an overview of current terrain modeling and authoring techniques, organized according to three categories: procedural modeling, physically‐based simulation of erosion and land formation processes, and example‐based methods driven by scanned terrain data. We compare and contrast these techniques according to several criteria, specifically: the variety of achievable landforms; realism from both a perceptual and geomorphological perspective; issues of scale in terms of terrain extent and sampling precision; the different interaction metaphors and attendant forms of user‐control, and computation and memory performance. We conclude with an in‐depth discussion of possible research directions and outstanding technical and scientific challenges.