Periodic variation method for blind symbol rate estimation

In order to obtain unknown symbol rate of incoming signal at a receiver, in this paper, cyclostationary features of linear digitally modulated signals are exploited by proposed periodic variation method. A low complexity but highly accurate symbol rate estimation technique is obtained. The proposed method is based on a superposed epoch analysis over autocorrelations obtained blindly in different sampling frequencies. The obtained autocorrelations are analyzed in the frequency domain, and it is seen that there are large oscillations when the autocorrelation is obtained around the symbol rate. Then, a superposed epoch analysis is developed in order to estimate symbol rate based of the periodic variations on the frequency responses of autocorrelations. The proposed algorithm is quite accurate in the noisy environment because the noise is having no frequency component after taking Fourier transform of autocorrelations in all sampling rates, and this feature is also valid for the offset frequency that the purposed estimation is not affected by offset frequency. Thus, a successful blind symbol rate estimation algorithm is obtained, and it performs much better error performance than those using the well‐known cyclic correlation based symbol rate estimations, as it is proven by the obtained performances presented in the paper. Copyright © 2013 John Wiley & Sons, Ltd.     

Structural advantages of rectangular-like channel cross-section on electrical characteristics of silicon nanowire field-effect transistors

We have experimentally demonstrated structural advantages due to rounded corners of rectangular-like cross-section of silicon nanowire (SiNW) field-effect transistors (FETs) on on-current (I_ON), inversion charge density normalized by a peripheral length of channel cross-section (Q_inv) and effective carrier mobility (μ_eff). The I_ON was evaluated at the overdrive voltage (V_OV) of 1.0 V, which is the difference between gate voltage (V_g) and the threshold voltage (V_th), and at the drain voltage of 1.0 V. The SiNW nFETs have revealed high I_ON of 1600 μA/μm of the channel width (w_NW) of 19 nm and height (h_NW) of 12 nm with the gate length (L_g) of 65 nm. We have separated the amount of on-current per wire at V_OV = 1.0 V to a corner component and a flat surface component, and the contribution of the corners was nearly 60% of the total I_ON of the SiNW nFET with L_g of 65 nm. Higher Q_inv at V_OV = 1.0 V evaluated by advanced split-CV method was obtained with narrower SiNW FET, and it has been revealed the amount of inversion charge near corners occupied 50% of all the amount of inversion charge of the SiNW FET (w_NW = 19 nm and h_NW = 12 nm). We also obtained high μ_eff of the SiNW FETs compared with that of SOI planar nFETs. The μ_eff at the corners of SiNW FET has been calculated with the separated amount of inversion charge and drain conductance. Higher μ_eff around corners is obtained than the original μ_eff of the SiNW nFETs. The higher μ_eff and the large fractions of I_ON and Q_inv around the corners indicate that the rounded corners of rectangular-like cross-sections play important roles on the enhancement of the electrical performance of the SiNW nFETs.     

Prediction of energy consumption for LoRa based wireless sensors network

Wireless Networks - This paper shows a method for predicting the lifetime of a wireless sensor network based on the LoRa Ra-01 wireless modules. To develop a prediction model of the energy...     

An efficient network-switch scheduling for real-time applications

Bursts consist of a varying number of asynchronous transfer mode cells corresponding to a datagram. Here, we generalized weighted fair queueing to a burst-based algorithm with preemption. The new algorithm enhances the performance of the switch service for real-time applications, and it preserves the quality of service guarantees. We study this algorithm theoretically and via simulations.     

Adaptive multichannel decision feedback equalization for volterra type nonlinear communication channels

A model-based approach for the decision feedback equalization of Volterra type nonlinear communication channels is proposed such that the linear model-based decision feedback equalization can be considered as a special case of the proposed approach. In designing the decision feedback equalizer, the nonlinear decision feedback equalization problem is visualized as a linear, multichannel equalization problem. A complete modified Gram–Schmidt orthogonalization of the input vector is achieved by using modified sequential processing multichannel lattice stages. The elements of the multichannel desired signal vector are then estimated from the new orthogonal set by using only scalar operations. The probability of error performance of the proposed equalizer is improved by the estimation of the elements of the desired signal vector through a sigmoid activation function so that a polynomial perceptron equalizer is realized. The comparative computational complexity calculations and performance results of the proposed decision feedback equalizer are also provided.     

Performance analysis of dual-hop fixed-gain AF relaying systems with OSTBC over Nakagami-m fading channels

In this paper, we present outage probability and symbol error rate (SER) performance analyses of a dual-hop transmission using fixed-gain amplify-and-forward relaying in flat Nakagami-m fading channels. The system under consideration is equipped with multiple antennas at source and destination adopting orthogonal space-time block coding to provide transmit diversity and maximum ratio combining to provide receive diversity, respectively. For integer and half-integer m values, closed forms of exact outage probability and moment generating function (MGF) expressions are derived through cumulative distribution function (CDF) of the overall system signal-to-noise ratio. Closed-form exact SER expressions based on the overall CDF are obtained for binary phase shift keying, binary frequency shift keying and M-ary pulse amplitude modulation. Exact SER expressions based on the MGF method are also obtained for binary differential phase shift keying, M-ary phase shift keying and M-ary quadrature amplitude modulation. Moreover, the asymptotic diversity order analysis is performed through derivations of asymptotic outage probability and SER. Theoretical analyses are validated by Monte Carlo simulations showing perfect match between each other.     

Wind turbine speed control of a contactless piezoelectric wind energy harvester

ABSTRACT

Wind turbine control is an important task to make the electricity generation secure in terms of energy demand and machine safety. It also yields to control the desired power level and optimized energy because of the assignment of turbine speed. The contactless piezoelectric wind energy harvester (CPWEH) used in this study has three piezoelectric layers located around the shaft with 120 degrees apart and they are buckled by the magnetic force without any physical contact. The superiority of this device is to generate energy for low wind speeds such as 1.5 m/s. However, for high speeds, high total harmonic distortions (THDs) govern the waveforms, thus controlling the turbine speed becomes necessary for optimizing the output power. Encouraged by this, a small low inertia dc generator is coupled with the wind turbine, and the generator terminals are connected to a resistor through a power switch to generate a braking torque that opposes to wind speed direction. By controlling the switch properly, turbine speed is ensured to remain within a certain band, which accordingly prevents the turbine from rotating very fast at damaging wind speeds. Several experiments are performed on the developed CPWEH with/without the presented control scheme which prove the existence of promising performance of our proposal.     

Entropy production due to free convection in partially heated isosceles triangular enclosures

A numerical analysis of the entropy production has been performed due to natural convection heat transfer and fluid flow in isosceles triangular enclosures with partially heated from below and symmetrically cooled from sloping walls. Governing equations are solved by finite difference method. Governing parameters on flow and temperature fields are Rayleigh number (10³  Ra  8.8 × 10⁵), dimensionless length of heater (0.25  (ℓ′ = ℓ/L)  1.0), dimensionless location of heater (0.25  (c′ = c/L)  0.75) and inclination angle of slopping walls (30°  β  60°). Heat transfer results are presented in terms of local and mean Nusselt numbers (Nu) while entropy production results are shown with entropy production number (N_s) and Bejan number (Be). Isotherms, streamlines, contours of entropy production due to heat transfer and fluid friction irreversibility are plotted. It is observed that entropy production number increases but Bejan number decreases with increasing of Rayleigh number. However, both entropy production due to heat transfer and fluid friction irreversibility are affected by higher inclination angle of triangle and length of heater.     

Fatty acid/poly(methyl methacrylate) (PMMA) blends as form-stable phase change materials for latent heat thermal energy storage

Fatty acids such as stearic acid (SA), palmitic acid (PA), myristic acid (MA), and lauric acid (LA) are promising phase change materials (PCMs) for latent heat thermal energy storage (LHTES) applications, but high cost is the most drawback which limits the utility area of them in thermal energy storage. The use of fatty acids as form-stable PCM will increase their feasibilities in practical LHTES applications due to reduced cost of the energy storage system. In this regard, a series of fatty acid/poly(methyl methacrylate) (PMMA) blends, SA/PMMA, PA/PMMA, MA/PMMA, and LA/PMMA were prepared as new kinds of form-stable PCMs by encapsulation of fatty acids into PMMA which acts as supporting material. The blends were prepared at different mass fractions of fatty acids (50, 60, 70, 80, and 90% w/w) to reach maximum encapsulation ratio. All blends were subjected to leakage test by heating the blends over the melting temperature of the PCM. The blends that do not allow leakage of melted PCM were identified as form-stable PCMs. The form-stable fatty acid/PMMA (80/20 wt.%) blends were characterized using optic microscopy (OM), viscosimetry, and Fourier transform infrared (FT-IR) spectroscopy methods, and the results showed that the PMMA was compatible with the fatty acids. In addition, thermal characteristics such as melting and freezing temperatures and latent heats of the form-stable PCMs were measured by using differential scanning calorimetry (DSC) technique and indicated that they had good thermal properties. On the basis of all results, it was concluded that form-stable fatty acid/PMMA blends had important potential for some practical LHTES applications such as under floor space heating of buildings and passive solar space heating of buildings by using wallboard, plasterboard or floor impregnated with a form-stable PCM due to their satisfying thermal properties, easily preparing in desired dimensions, direct usability without needing an add encapsulation and eliminating the thermal resistance caused by shell and thus reducing cost of LHTES system.     

Mechanical properties of a reinforced composite polymer electrolyte membrane and its simulated performance in PEM fuel cells

The hygro-thermo-mechanical properties and response of a class of reinforced perfluorosulfonic acid membranes (PFSA), that has potential application as an electrolyte in polymer fuel cells, are investigated through both experimental and numerical modeling means. A critical set of material properties, including Young's modulus, proportional limit stress, break stress and break strain, is determined for a range of temperature and humidity levels in a custom-built environmental test apparatus. The swelling strains are also determined as functions of temperature and humidity level. To elucidate the mechanical response and the potential effect these properties have on the mechanical durability, mechanics-based simulations are performed using the finite element method (ABAQUS). The results indicate that the relatively high strength of the experimental membrane, in combination with its relatively low in-plane swelling due to water absorption, should have a positive influence on membrane durability, potentially leading to longer life times for polymer electrolyte membrane fuel cells (PEMFC).