Effect of Gamma Irradiation on Biochemical Properties of Grape Seeds

In the present study, grape seed samples (Alicante Bouschet, Cabernet Franc, Cinsault, Merlot, Shiraz) were treated with 1.0, 3.0, 5.0, and 7.0 kGy of gamma radiation. Effect of irradiation dose on free fatty acids (FFA), peroxide value (PV), sterol, fatty acid composition, phenolic content, antioxidant activity of the seed oils, and chemical (dry matter, fat, ash, total sugar, invert sugar) changes of grape seeds were determined. Regarding fatty acid composition, oleic acid (C18:1) and linoleic acid (C18:2) levels decreased. β-sitosterol content with a highest percentage among sterols in grape seed oils decreased due to gamma irradiation. Generally gamma irradiation increased free fatty acids and peroxide value of the oils; however, phenolic content and antioxidant capacity of grape seeds decreased.     

Optimization of dielectric heating parameters in the production of high‐voltage LiNiPO4‐core and carbon‐shell ceramics

Excellent core‐shell morphology and nanoscale high‐voltage LiNiPO₄@C cathode materials have been synthesized by a low‐level and long‐time microwave and solvothermal synthesis methodology. The effects of the changing physicochemical parameters on the crystal‐quality and electrochemical properties of the products have been evaluated in relation to the cycling stability. X‐ray diffraction analysis shows that it is possible to synthesize phase‐pure LiNiPO₄ material when the reaction parameters are carefully elaborated. High‐resolution transmission electron microscopy analysis reveals a core‐shell morphology with a coating thickness of 6‐8 nm for 30 minutes at 180°C solvothermal temperature and time‐spread microwave energy. This mentioned cathode material exhibits the best electrochemical properties, achieving a discharge capacity of 157 mAh·g^?1 at a 0.l C current rate, and shows a remarkable 81% capacity retention at the end of the 80th cycle.     

Effect of calcium hydroxide removal techniques on the bond strength of root canal sealers

To evaluate the influence of calcium-hydroxide(CH) with different vehicles on the push-out bond strength of different canal sealers to radicular dentin. 152 decrowned single-rooted human teeth were used. After preparation of root canals with nickel-titanium rotary files, 8 roots served as control groups. Then, the roots were divided as follows: (1) Calasept and (2) Surepaste (n = 72). Roots were further subgrouped according to the CH removal techniques: (1) %17 ethylenediaminetetraacetic acid (EDTA) + rotary file, (2) %17EDTA + hand file, and (3) %17EDTA (n = 24). Eight roots from each group sectioned longitudinally, divided into two pairs and photographed by stereomicroscope (n = 16). The remaining 16 roots in CH intracanal dressing groups were further divided into 2 subgroups according to the sealer used: (1) AH-Plus-jet and (2) Apexit-Plus (n = 8). Bond strengths of the root canal sealers to root canal dentin were measured using a push-out test setup. The data were statistically analyzed using multivariate analysis of variance p = 0.05. The push-out bond strength values were significantly affected by type of vehicle and the removal techniques (p < 0.05). The mean bond strength of AH-Plus-jet was significantly higher than Apexit-Plus, regardless of type of vehicle and the removal techniques (p < 0.05). There was no difference between vehicles on CH removal (p > 0.05). When examining the removal techniques, only irrigation with %17 EDTA left significantly larger amount of residue (p < 0.05). AH-Plus-jet showed better dislocation resistance than Apexit-Plus. Type of vehicle does not play a fundamental role in the degree of persistence of CH residues on the dentin walls. Instrumentation improves the removal efficiency of CH from root canal.     

DYNAMICS AND CONTROL OF CROSS-FLOW GRAIN DRYERS I. MODEL DEVELOPMENT AND TESTING

A general dynamic model for a cross-flow dryer is developed from fundamental balance equations. Six dimensionless groups that govern the process are defined and the resulting dimensionless equations are solved with the method of lines, using the Advanced Continuous Simulation Language software package ACSL (1986). The mesh influence on the numerical solution is investigated, and the assumption of quasi-steady state for the air is discussed. Application of the model to rice-drying experiments shows good agreement, and the results underline the potential of the model and the numerical solution strategy in obtaining critical physical insight towards the operation of cross-flow rice dryers.     

Improving hydrophobicity on polyurethane-based synthetic leather through plasma polymerization for easy care effect

This study reports on the deposition of a hydrophobic coating on polyurethane (PU)-based synthetic leather through a plasma polymerization method and investigates the hydrophobic behavior of the plasma-coated substrate. The silicon compound of hexamethyldisiloxane (HMDSO), inactive gas argon (Ar), and toluene were used to impart surface hydrophobicity to a PU-based substrate. Surface hydrophobicity was analyzed by water contact angle measurements. Surface hydrophobicity was increased by deposition of compositions of 100% HMDSO, 3:1 HMDSO/toluene, and 1:1 HMDSO/toluene. Optimum conditions of 40 W, 30 s plasma treatment resulted in essentially the same initial contact angle results of approximately 100° for all three treatment compositions. The initial water contact angle for untreated material was about 73°. A water droplet took 1800 s to spread out on the plasma-treated sample after it had been placed on the sample surface. An increase in plasma power also led to a decrease in contact angle, which may be attributed to oxidization of HMDSO during plasma deposition. XPS analysis showed that plasma polymerization of HMDSO/toluene compositions led to a significant increase in atomic percentage of Si compound responsible for the hydrophobic surface. The easy clean results for the treated and untreated PU-based synthetic leather samples clearly showed that the remaining stain on the plasma-polymerized sample was less than that of untreated sample. The plasma-formed coating was both hydrophobic and formed a physical barrier against water and stain.     

Soluble and conductive polypyrrole copolymers containing silicone tegomers

Soluble and processable conductive copolymers of silicone tegomers and pyrrole were developed. This was easily accomplished by the oxidative polymerization of pyrrole monomer by Ce(IV) salt in the presence of silicone tegomers with hydroxyl chain ends. The resulting copolymers were soluble in dimethylformamide. The products were characterized by Fourier transform infrared, ¹H‐NMR, and four‐point probe conductivity, and their surface properties were investigated with contact‐angle measurements. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2896–2901, 2003     

The preparation of core–shell Al2O3/Ni composite powders by electroless plating

Core–shell nanostructured Ni-coated Al₂O₃ composite powders were synthesised by using the electroless plating method. The influence of the chemical components and powder concentration in the Ni coating was investigated by scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction techniques. The results show that the concentration of the plating components plays an important role in the formation of core–shell Al₂O₃/Ni composite powders. The nickel content in the composite powders could be effectively controlled by adjusting the nickel chloride content and the concentration of NaH₂PO₂·H₂O in the plating solution. The nanostructure of the crystalline Ni coatings was observed to be very attractive for achieving good bonding between ceramic particles and matrices for composite production.     

Catalytic effect of potassium carbonate on carbothermic production of hexagonal boron nitride

Effect of potassium carbonate addition on the carbothermic formation of hexagonal boron nitride (hBN) was investigated by keeping the K₂CO₃ added B₂O₃+C mixtures in nitrogen atmosphere at 1400 °C for 40–160 min. K₂CO₃ amount was varied in the range of 10–60 wt% of the B₂O₃+C mixture. Products were subjected to XRD and quantitative analyses, SEM and TEM observations, and particle size measurement. Amount of hBN increased considerably with K₂CO₃ addition; also particle size and crystallinity improved. Catalytic role of K₂CO₃ was suggested as forming a potassium borate melt in which hBN particles form, in addition to carbothermic formation reaction. Effect of K₂CO₃ on increasing the hBN amount decreased when it was used over 40%. This was attributed to the rapid evaporation of the formed potassium borate liquid.     

Preparation and thermal properties of polyethylene terephthalate/huntite–hydromagnesite composites

In this report, it was aimed to the improve thermal stability of polyethylene terephthalate (PET) by adding huntite/hydromagnesite minerale. PET/huntite/hydromagnesite composites were prepared by adding various proportions of huntite/hydromagnesite to PET. The chemical structures of the composites were characterized by Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) analysis. Thermal properties of the composites were determined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Glass‐transition temperatures and char yields increased with the increase of the huntite/hydromagnesite content in the composites. The surface morphologies of the composites were investigated by a scanning electron microscopy. The obtained results proved that the composite system is more thermally stable than the pure PET itself. POLYM. COMPOS., 37:3275–3279, 2016. © 2015 Society of Plastics Engineers     

The Nucleation Effect of PbSe Additive on Bi2Sr2CaCu2Oδ Glass Ceramics

Glass and Ceramics - The crystallisation kinetics and effects of doping on Bi2Sr2CaCu2Oδ (BSCCO) glass ceramic system with 0.0%, 0.1%, 0.3% and 0.5% PbSe were investigated in this study....