Direct ethanol production from barley beta-glucan by sake yeast displaying Aspergillus oryzae beta-glucosidase and endoglucanase

Three beta-glucosidase- and two endoglucanase-encoding genes were cloned from Aspergillus oryzae, and their gene products were displayed on the cell surface of the sake yeast, Saccharomyces cerevisiae GRI-117-UK. GRI-117-UK/pUDB7 displaying beta-glucosidase AO090009000356 showed the highest activity against various substrates and efficiently produced ethanol from cellobiose. On the other hand, GRI-117-UK/pUDCB displaying endoglucanase AO090010000314 efficiently degraded barley beta-glucan to glucose and smaller cellooligosaccharides. GRI-117-UK/pUDB7CB codisplaying both beta-glucosidase AO090009000356 and endoglucanase AO090010000314 was constructed. When direct ethanol fermentation from 20 g/l barley beta-glucan as a model substrate was performed with the codisplaying strain, the ethanol concentration reached 7.94 g/l after 24 h of fermentation. The conversion ratio of ethanol from beta-glucan was 69.6% of the theoretical ethanol concentration produced from 20 g/l barley beta-glucan. These results showed that sake yeast displaying A. oryzae cellulolytic enzymes can be used to produce ethanol from cellulosic materials. Our constructs have higher ethanol production potential than the laboratory constructs previously reported.     

Gel permeation chromatography of polyoxymethylene

Gel permeation chromatography of polyoxymethylene has been studied using N,N-dimethylformamide as the solvent. Polyoxymethylene samples used here are a copolymer of tetraoxane with 1,3-dioxolane and a commercial polyoxymethylene whose molecular weight distributions are moderately broad. Their intrinsic viscosities [η] range from 1.4 to 2.8 dl/g. Factors affecting chromatograms are discussed, and the operating conditions were determined by using the analytical scale GPC. On the basis of these operating conditions, the molecular weight fractionation of polyoxymethylene was carried out by using the preparative scale GPC. It was found that polyoxymethylene can be effectively fractionated to give seven to ten fractions each of them containing the fractionated polymer ranging in weight from 0.2 to 8 mg when 40 mg polymer sample was used for a run of the measurement. The fractionated polymers were also found to have a narrow molecular weight distribution within a single peak, and their M_w/M_n values decrease with increasing molecular weight.     

Reduction and unusual recovery in the reversible hydrogen storage capacity of V1−xTix during hydrogen cycling

The effect of the vanadium content on the cyclic stability of V–Ti binary alloys was investigated. V_1−xTi_x, x = 0.2 and 0.5 samples were hydrogenated and dehydrogenated at 410 K and 553 K respectively, for more than 100 times. During hydrogen cycling, reduction in the reversible hydrogen storage capacity was clearly observed from both samples. No prominent V-effect was found. In fact, the reduction rates of two samples were similar; both samples showed a ∼25% reduction in the reversible hydrogen storage capacity after 100 cycles. In addition, the shape of the pressure–composition-isotherm (PCT) curves was significantly altered over the testing cycle period; the absorption and desorption plateaus got markedly inclined and the hysteresis became evidently smaller. We found that even after the hydrogen storage capacity of V_1−xTi_x was significantly reduced, at low enough temperature V_1−xTi_x was able to absorb hydrogen as much as it did at the first cycle. Furthermore, the reversible hydrogen storage capacity of V_0.8Ti_0.2 at 410 K was recovered to a certain degree after hydrogenating the sample at low temperatures.     

Experimental investigation of melt pool behaviour during selective laser melting by high speed imaging

Melt pool behaviour and the characteristics of the surrounding metal powder during selective laser melting (SLM) are captured using high-speed imaging, and the influence of the substrate temperature and the line building sequence on the formation of the built structure and the generation of spatter particles is experimentally investigated. The results indicate that the substrate temperature has a measurable effect on the formation of droplets and the generation of spatter particles, while the volume specific energy density of the process was the principal factor affecting the built structure.     

Photocatalytic hydrogenation of acetophenone derivatives and diaryl ketones on polycrystalline titanium dioxide

In the absence of molecular oxygen, various aromatic ketones such as acetophenone derivatives and diaryl ketones were photocatalytically hydrogenated on polycrystalline titanium dioxide (Degussa P25) under UV light irradiation (> 340 nm). The desired secondary alcohols were obtained with excellent chemical efficiency (almost 100% yields for 10 examples) by choosing ethanol as a sacrificial hole scavenger, which was oxidized into acetaldehyde.     

Experimental study on latent heat storage characteristics of W/O emulsion -Supercooling rate of dispersed water drops by direct contact heat exchange-

Recently, much attention has been paid to investigate the latent heat storage system. Using of ice heat storage system brings an equalization of electric power demand, because it will solved the electric -power-demand-concentration on day-time of summer by the air conditioning. The flowable latent heat storage material, Oil/Water type emulsion, microencapsulated latent heat material-water mixture or ice slurry, etc., is enable to transport the latent heat in a pipe. The flowable latent heat storage material can realize the pipe size reduction and system efficiency improvement. Supercooling phenomenon of the dispersed latent heat storage material in continuous phase brings the obstruction of latent heat storage. The latent heat storage rates of dispersed water drops in W/O (Water/Oil) emulsion are investigated experimentally in this study. The water drops in emulsion has the diameter within 3 ～ 25μm, the averaged water drop diameter is 7.3μm and the standard deviation is 2.9μm. The direct contact heat exchange method is chosen as the phase change rate evaluation of water drops in W/O emulsion. The supercooled temperature and the cooling rate are set as parameters of this study. The evaluation is performed by comparison between the results of this study and the past research. The obtained experimental result is shown that the 35K or more degree from melting point brings 100% latent heat storage rate of W/O emulsion. It was clarified that the supercooling rate of dispersed water particles in emulsion shows the larger value than that of the bulk water.     

Surface‐discharge electrode design methods for ACPDPs

Abstract— In order to lower development costs and to shorten development time, small panels, under 10‐in on the diagonal, are used for the experiments to improve the luminous efficiency of plasma‐display panels. However, it is difficult to show the same results as those of large panels, over 40 in. on the diagonal. In this paper, first, we show that the luminous efficiency and the voltage margin of mini‐panels are not obtained with large panels by using an actual 46‐in. PDP. The reason is that the resistance in the large panels is larger than that in the mini panels and the voltage drop in the large panels are larger than in mini‐panels. Therefore, we conclude that the bus electrode width and the transparent electrode width are important factors in the design of large PDPs. Next, we show the technique of designing large panels by using a database obtained from mini‐panels. The estimated cell‐design results show good agreement with an actual 46‐in. PDP in luminous efficiency and minimum sustain voltage. We show that a desired large PDP can be obtained by using the cell design proposed in the present paper.     

Formalization and Analysis of Class Loading in Java

Since Java security relies on the type-safety of the JVM, many formal approaches have been taken in order to prove the soundness of the JVM. This paper presents a new formalization of the JVM and proves its soundness. It is the first model to employ dynamic linking and bytecode verification to analyze the loading constraint scheme of Java2. The key concept required for proving the soundness of the new model is augmented value typing, which is defined from ordinary value typing combined with the loading constraint scheme. In proving the soundness of the model, it is shown that there are some problems inside the current reference implementation of the JVM with respect to our model. We also analyze the findClass scheme, newly introduced in Java2. The same analysis also shows why applets cannot exploit the type-spoofing vulnerability reported by Saraswat, which led to the introduction of the loading constraint scheme.     

Influence of water vapor on the reduction of cuprous chloride to copper microfibers

Reduction of cuprous chloride has been examined in various atmospheres, mostly at 600°C, to produce copper microfibers that can be applied as a filler for electromagnetic interference shielding and electron conductive paste composites. The reduction with hydrogen resulted in formation of a large amount of copper films, but fine particles and short filaments were obtained when carbon black was mixed into the raw material. The most promising copper microfibers with dimensions of several mm length and 1–10 m thickness could be produced with the system CuCl — C — H₂O using argon as a carrier gas, where H₂ and CO formed then probably reduced the vaporized CuCl molecules. Introduction of hydrogen gas into this system increased the yield of copper microfibers, though they became more bent, curved and kinked in shape. However, the morphology of the microfibers is still acceptable as a filler.