XIII. Yeast sequencing reports. Cloning and sequencing of the NES24 gene of Saccharomyces cerevisiae

We have cloned NES24 using a temperature-sensitive nes24-1 mutant as a host and sequenced a 3162 bp XhoI-EcoRI DNA fragment containing the NES24 gene. Computer analysis revealed that this segment contains a 1806 bp open reading frame which is needed for complementation of the nes24-1 mutation. We found SUP8 in the region upstream of the NES24 gene, placing the NES24 gene on chromosome XIII. A protein homology search indicated that NES24 encodes a new protein. The disruption of the NES24 gene resulted in temperature-sensitive growth. The sequence has been deposited in DDBJ/EmBL/GenBank data bases under Accession Number D15052.     

Design of electrofusion joints and evaluation of fusion strength using fusion simulation technology

Fusion simulation is one of the key techniques in designing and producing electrofusion (EF) joints for gas distribution and in evaluating fusion joint integrity. This paper describes the result of a numerical simulation of a thermal fusion process, using the finite element method. A nonlinear heat transfer computer program was used to obtain the temperature profile of a large electrofusion joint at fusion. The effects of applied voltage, heating time, wire pitch, and ambient temperature were examined for designing a 150-mm EF joint. A method to shorten the cooling time was also investigated. The fusion condition range suitable for a 150-mm EF joint was found to be slightly narrower than that suitable for a 50-mm EF joint. Examination of the effect of wire pitch revealed that if the pitch is extremely large, thermal degradation starts in the resin close to the wire before the fusion-interface strength reaches the maximum value. We have developed a program to simulate the process of closing the gap between the pipe and the joint due to resin expansion and melting after the power is supplied.     

DX centers in AlxGa1-xAs bulk alloy,AlAs/GaAs ordered,and disordered superlattices

Properties of theDX centers in Al_0.5Ga_0.5As bulk alloy (b-AL), (AlAs)₂ (GaSa)₂ ordered superlattice (o-SL) and (AlAs) _m (GaAs) _n disordered superlattice (d-SL) (m = 1, 2, 3,n = 1, 2, 3) with the same macroscopic composition were measured and compared. By deconvolution of deep level transient spectroscopy (DLTS) spectrum due to theDX center, we have found a decrease in the number of separate peaks in DLTS spectrum in an intentionally atomic ordered arrangement. Visiting Scholar of the Japan Society for the Promotion of Science. On leave from Department of Electrical Engineering, San Jose State University, San Jose, California 95192-0084, USA.     

Direct contact melting of porous material

The direct contact melting of a porous material is investigated experimentally and analytically. The phase change material (PCM) is made of fine ice particles of a nearly uniform diameter, which is changed as a parameter. In the analysis, two models are proposed. One is calculated as the direct contact melting of a monolithic sample and another is treated as an assembly of the direct contact melting of the individual particles. As a result, it was found that the heat flux increased with the diameter, due to increase of permeability in a case of small diameter. But, in a case of large diameter, the heat flux decreased as the particle diameter increased because the direct contact melting occurred independently for the individual particles.     

In Situ Observation of Phase Separation of a Barium Borate Melt in a Stable Immiscibility Region under Microgravity

The precipitation of droplets was directly observed on a BaO–B₂O₃ melt in a drop shaft experiment. This is the first time that precipitation of droplets has been observed in a 4.5 s drop test. The melt film of 4BaOz96B₂O₃ (mol%) held on a platinum wire loop was heated above the critical tem-perature to produce uniformity and was cooled down to the phase separation temperature range. Phase separation of the melt was observed directly with a video camera. The IR image of the melt was simultaneously detected with a CCD array and was converted into a two-dimensional thermograph.     

Formation and Crystallization of Yttrium Aluminosilicate Glasses Containing Calcium Oxide

Formation of yttrium aluminosilicate glasses containing calcium oxide from batches melted at 1550°C was investigated. Densities and thermal expansion coeflcients were measured for some glasses. In a specific compositional region, crystals with a needlelike habit were observed in the glass matrix. A crystal in the form of a tubular hexagonal prism was identified as Ca₄Y₆0(Si0₄)₆.     

Dynamic Mechanical Properties and Adhesive Strengths of Emulsion Polymer by Power Feed Technique, I

Dynamic mechanical properties and adhesive strengths of power feed copolymer and random copolymer synthesized using styrene or methyl methacrylate and n-butyl acrylate were investigated. Although the two systems were synthesized from the same raw materials, power feed copolymer had a very broad transition compared with random copolymer. This fact was explained by the fact that the system synthesized through power feed method was an alloy of copolymers which are a continuous series from monomer A rich copolymers to monomer B rich copolymers. The dynamic mechanical behavior of film cast from solution was almost the same as that of emulsion film, which indicated more extensive application of power feed copolymer. In the P(nBA/St) system, power feed copolymer maintained its adhesive strengths over a wide temperature range compared with random copolymer. The absolute value, however, was not so high. This was due to the low cohesive strengths of the films.     

Dynamic Mechanical Properties and Adhesive Joint Strengths of Emulsion Polymers Produced by Power Feed Technique. III. Adhesive Joint Strengths of Grafted Power Feed Copolymer

Power feed copolymers were synthesized using styrene and n-butyl acrylate through non-uniform feeding emulsion polymerization. Poly(vinyl alcohol) (PVA) was used as a protective colloid, onto which vinyl monomers were grafted. Power feed copolymer had a very broad glass transition temperature compared with random copolymer, even if grafting and/or crosslinking were introduced to the system. This tendency was almost the same as the non-grafted power feed copolymer where only low molecular weight surfactant was used.

Adhesive joint strengths of power feed copolymers were evaluated compared with random copolymers. In the case of usual linear power feed copolymer, the adhesive joint strengths were not higher than those of random copolymer, which was considered to be due to the lower film strengths of the power feed copolymer. Power feed copolymer having grafting showed slightly higher adhesive joint strengths over a wide range of temperatures than random copolymer. When crosslinking was introduced to the system, power feed copolymer showed much higher adhesive joint strengths over a wide temperature range.     

New type of tin support for hydroprocessing catalyst

TiN supported molybdenum sulfide catalysts showed much higher activity for cleavage of C-C bonds than oxide supported molybdenum sulfide catalysts, indicating the possibility of a new generation of supports for hydroprocessing catalysts.