Methods of Verifying Continuous Automatic Belt Weighers: State and Prospects

The basic methods of verifying continuous automatic belt weighers are described. A comparative analysis of these methods on the basis of experimental studies is made and ways of implementing the results in industry are recommended.     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.     

The anisotropic effect of a weak magnetic field on the photoconductivity of C<Subscript>60</Subscript> single crystals

The effect of crystal orientation on the photogeneration of free charge carriers was studied for C₆₀ single crystals in a weak magnetic field. The photoconductivity sharply depends on the orientation of magnetic field with respect to the crystallographic directions, showing a 5–8% increase for seven axes of the C₆₀ crystal.     

State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

Oligo(ethylene oxide) side‐chain steric screening effects on conductimetric properties of grafted poly(4‐vinylpyridinium) salts in aqueous solutions

A set of poly[N‐oligo(ethylene oxide)yl 4‐vinylpyridinium tosylate] (P4VOEOOTs) has been prepared by spontaneous polymerization of 4‐vinylpyridine. This method gives a grafted polyelectrolyte having a positive charge on every backbone pyridinic moiety. The P4VP15Ts, P4VP164Ts, P4VP350Ts and P4VP750Ts aqueous solution conductivities were determined in the concentration range from 6 × 10^?4 to 10^?2 M at 25 °C. The variation of the conductivity versus concentration of the investigated system exhibits typical polyelectrolyte behaviour. The polyelectrolyte mobility was found to be dependent on the oligo(ethylene oxide) (OEO) side‐chain length. Manning's rod‐like model fails to describe these results. A simple steric effect is proposed to explain the influence of the OEO length. Copyright © 2003 Society of Chemical Industry     

Effects of surface charge, micro-bubble size and particle size on removal efficiency of electro-flotation.

Flotation is a water treatment alternative to sedimentation, and uses small bubbles to remove low-density particles from potable water and wastewater. The effect of zeta potential, bubble size and particle size on removal efficiency of the electro-flotation process was investigated because previous model-simulations indicated that these attributes are critical for high collision efficiency between micro-bubbles and particles. Solutions containing Al3+ as the metal ion were subjected to various conditions. The zeta potentials of bubbles and particles were similar under identical conditions, and their charges were influenced by metal ion concentration and pH. Maximum removal efficiency was 98 and 12% in the presence and absence of flocculation, respectively. Removal efficiency was higher when particle size was similar to bubble size. These results agree with modelling simulations and indicate that collision efficiency is greater when the zeta potential of one is negative and that of the other is positive and when their sizes are similar.     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

Assessing stem cell research productivity

Honour Index (HoI), a method to evaluate research performance within different research fields, was derived from the impact factor (IF). It can be used to rate and compare different categories of journals. HoI was used in this study to determine the scientific productivity of stem cell research in the Asian Four Dragons (Hong Kong, Singapore, South Korea and Taiwan) from 1981 to 2001. The methodology applied in this study represents a synthesis of universal indicator studies and bibliometric analyses of subfields at the micro-level. We discuss several comparisons, and conclude the developmental trend in stem cell research for two decades. This revised version was published online in August 2006 with corrections to the Cover Date.     

A redundant multivalued logic for a 10-Gb/s CMOS demultiplexer IC

A redundant multivalued logic is proposed for high-speed communication ICs. In this logic, serial binary data are received and converted into parallel redundant multivalued data. Then they are restored into parallel binary data. Because of the multivalued data conversion, this logic makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was fabricated using a 0.18-/spl mu/m CMOS process. The IC achieved an operating speed of 10 Gb/s with a supply voltage of only 1.3 V and with power consumption of 38 mW. This logic may achieve CMOS communication ICs with an operating speed several times greater than 10 Gb/s.     

Effect of film thickness on hydrogen content in a-Si : H

The hydrogen content, its depth distribution, and its bonding configuration have been studied in hydrogenated amorphous silicon prepared by plasma-enhanced chemical vapor deposition with hydrogen-diluted silane. Nuclear reaction analysis and infrared spectroscopy were used to determine the total amount of hydrogen and its bonded component, respectively. It has been established that the total concentration of hydrogen does not depend on the film thickness, and has a uniform depth profile. The concentration of bonded hydrogen changes with the film thickness within the measurement accuracy. The data obtained suggest the presence of molecular (non-bonded) hydrogen, uniformly distributed in concentration across the film thickness.