Carbon nanotubes and onions from carbon monoxide using Ni(acac)2 and Cu(acac)2 as catalyst precursors

New catalyst precursors (copper and nickel acetylacetonates) have been used successfully for the synthesis of carbon nanotubes and onion particles from carbon monoxide. Catalyst nanoparticles and carbon products were produced by metal-organic precursor vapour decomposition and catalytic disproportionation of carbon monoxide in a laminar flow reactor at temperatures between 705 and 1216 °C. Carbon nanotubes (CNTs) were formed in the presence of nickel particles at 923-1216 °C. The CNTs were single-walled, 1-3 nm in diameter and up to 90 nm long. Hollow carbon onion particles (COPs) were produced in the presence of copper particles at 1216 °C. The COPs were from 5 to 30 nm in diameter and consisted of several concentric carbon layers surrounding a hollow core. The results of computational fluid dynamics calculations to determine the temperature and velocity profiles and mixing conditions of the species in the reactor are presented. The mechanisms for the formation of both CNTs and COPs are discussed on the basis of the experimental and computational results.     

Dense subgraph maintenance under streaming edge weight updates for real-time story identification

Recent years have witnessed an unprecedented proliferation of social media. People around the globe author, everyday, millions of blog posts, social network status updates, etc. This rich stream of information can be used to identify, on an ongoing basis, emerging stories, and events that capture popular attention. Stories can be identified via groups of tightly coupled real-world entities, namely the people, locations, products, etc, that are involved in the story. The sheer scale and rapid evolution of the data involved necessitate highly efficient techniques for identifying important stories at every point of time. The main challenge in real-time story identification is the maintenance of dense subgraphs (corresponding to groups of tightly coupled entities) under streaming edge weight updates (resulting from a stream of user-generated content). This is the first work to study the efficient maintenance of dense subgraphs under such streaming edge weight updates. For a wide range of definitions of density, we derive theoretical results regarding the magnitude of change that a single edge weight update can cause. Based on these, we propose a novel algorithm, DynDens, which outperforms adaptations of existing techniques to this setting and yields meaningful, intuitive results. Our approach is validated by a thorough experimental evaluation on large-scale real and synthetic datasets.     

Solvent-free oxidation of benzyl alcohol using titania-supported gold–palladium catalysts: Effect of Au–Pd ratio on catalytic performance

The oxidation of benzyl alcohol with molecular oxygen under solvent-free conditions has been investigated using a range of titania-supported Au–Pd alloy catalysts to examine the effect of the Au–Pd ratio on the conversion and selectivity. The catalysts have been compared at high reaction temperature (160 °C) as well as at 100 °C, to determine the effect on selectivity since at lower reaction temperature the range of by-products that are formed are limited. Under these conditions the 2.5 wt.% Au–2.5 wt.% Pd/TiO₂ was found to be the most active catalyst, whereas the Au/TiO₂ catalyst demonstrated the highest selectivity to benzaldehyde. Toluene, formed via either a hydrogen transfer process or an oxygen transfer process, was observed as a major by-product under these forcing conditions.     

Solvent free liquid phase oxidation of benzyl alcohol using Au supported catalysts prepared using a sol immobilization technique

Solvent free oxidation of benzyl alcohol was investigated in the absence of a base using Au catalysts prepared by sol immobilization on titania and carbon supports. Comparison between the Au supported catalysts revealed that activity and distribution of products was dependent on the nature of support and heat treatment. Specifically, heat pre-treatment of the Au catalysts has a beneficial effect in terms of activity, but is detrimental in terms of selectivity to the benzaldehyde. We conclude that sol immobilization is a suitable technique for preparing gold catalysts with small particle size and narrow particle size distributions and very high activity and selectivity for benzyl alcohol oxidation.     

Modeling nonisothermal impregnation of fibrous media with reactive polymer resin

The manufacture of polymer composites through resin transfer molding (RTM) or structural reaction injection molding (SRIM) involves the impregnation of a fibrous reinforcement in a mold cavity with a reactive polymer resin. The design of RTM and SRIM operations requires an understanding of the various parameters, such as materials properties, mold geometry, and mold filling conditions, that affect the resin impregnation process. Modeling provides a potential tool for analyzing the relationships among the important parameters. The present work provides the physical model and finite element formulations for simulating the mold filling stage. Resin flow through the fibers is modeled using two-dimensional Darcian flow. Simultaneous resin reaction and heat transfer among resin, mold walls, and fibers are considered in the model. The proposed technique emphasizes the use of the least squares finite element method to solve the convection dominated mass and energy equations for the resin. Excellent numerical stability of the proposed technique provides a powerful numerical method for the modeling of polymer processing systems characterized by convection dominated transport equations. Results from example numerical studies for SRIM of polyurethane/glass fiber composites were presented to illustrate the application of the proposed model and numerical scheme.     

Direct synthesis of hydrogen peroxide from H2 and O2 using zeolite-supported Au catalysts

The direct synthesis of hydrogen peroxide from H₂ and O₂ using zeolite-supported Au catalysts is described and their activity is contrasted with silica- and alumina-supported Au catalysts. Two zeolites were investigated, ZSM-5 and zeolite Y. The effect of calcination of these catalysts is studied and it is found that for uncalcined catalysts high rates of hydrogen peroxide formation are observed, but these catalysts are unstable and lose Au during use. Consequently, reuse of these catalysts leads to lower rates of hydrogen peroxide formation. However, catalysts calcined at 400 °C are more stable and can be reused without loss of gold. The use of zeolites as a support for Au gives comparable rates of hydrogen peroxide formation to alumina-supported Au catalysts and higher rates when compared with silica-supported catalysts. prepared using a similar method. Zeolite Y-supported catalysts are more active than ZSM-5-supported catalysts for the stable calcined materials. It is considered that the overall activity of these supported catalysts may be related to the aluminium content as the activity increases with increasing aluminium content.     

Development of a virtual reality laboratory stressor

Virtual Reality - This research report describes the development of a virtual reality (VR) laboratory stressor to study the effects of exposure to stressful events. The aim of the research was to...     

Polyester functionalization for mycobacterial capture

Tuberculosis (TB) is one of the deadliest diseases known to man and ranks among the top ten global causes of fatalities. Children often develop a paucibacillary form of this disease which makes diagnosis arduous even with the aid of sophisticated techniques. In these cases, the concentration of bacteria in their sputum falls below the lowest limit of detection for sputum smear microscopy, the technique predominantly used in developing countries. In this study we aim to test the hypothesis that modifying a polymer, often used in buccal swabs, could assist in creating a capturing and concentrating oral swab for Mycobacterium tuberculosis (Mtb), the pathogenic bacterial species responsible for TB. Such a device will assist in meeting the detection limit and allow for rapid detection of the disease. The polymer used was a micro fibrous form of poly(ethylene terephthalate) (PET) which was surface functionalized with Concanavalin A (Con A), a lectin based adhesin with an affinity for the mannose groups on the Mtb cell wall. The functionalization was mediated with glutaraldehyde as bioconjugate molecule and found to produce a surface uniformly covered with Con A. Affinity studies between the modified fibers and the Mycobacterium bovis bacillus Calmette-Guérin (BCG), as Mtb mimic, were conducted to evaluate the capturing abilities of the substrate. The results indicate that the fibers avidly captured BCG and that the fibrous matrix aided in its function. Dilution studies showed successful capturing of the bacterial species at concentrations characteristic of paucibacillary cases. In this study a commercial polymeric material was successfully surface modified with a biological entity to create a substrate to which Mtb could adhere and accordingly be captured.     

High-throughput drilling of titanium alloys

Experiments of high-throughput drilling of Ti–6Al–4V at 183 m/min cutting speed and 156 mm³/s material removal rate (MRR) using a 4 mm diameter WC–Co spiral point drill were conducted. The tool material and geometry and drilling process parameters, including cutting speed, feed, and fluid supply, were studied to evaluate the effect on drill life, thrust force, torque, energy, and burr formation. The tool wear mechanism, hole surface roughness, and chip light emission and morphology for high-throughput drilling were investigated. Supplying the cutting fluid via through-the-drill holes has proven to be a critical factor for drill life, which can be increased by 10 times compared to that of dry drilling at 183 m/min cutting speed and 0.051 mm/rev feed. Under the same MRR of 156 mm³/s with a doubled feed of 0.102 mm/rev (91 m/min cutting speed), over 200 holes can be drilled. The balance of cutting speed and feed is essential to achieve long drill life and good hole surface roughness. This study demonstrates that, using proper drilling process parameters, spiral point drill geometry, and fine-grained WC–Co tool material, the high-throughput drilling of Ti alloy is technically feasible.     

In situ repair welding of steam turbine shroud for replacing a cracked blade

A root-cracked blade in a high-pressure steam turbine of a nuclear power plant had to be replaced with a new blade by cutting the shroud to remove the cracked blade. This necessitated in situ welding of a new shroud piece with the existing shroud after the blade replacement. The in situ welding of the shroud, a 12% Cr martensitic stainless steel with tempered martensite microstructure, was carried out using gastungsten arc welding and 316L austenitic stainless steel filler metal followed by localized postweld heat treatment at 873 K for 1 h using a specially designed electrical resistance-heating furnace. Mock-up trials were carried out to ensure that sound welds could be made under the constraints present during the in situ repair welding operation. In situ metallography of the repair weld after postweld heat treatment confirmed the adequate tempering of the martensitic structure in the heat-affected zone. Metallurgical investigations carried out in the laboratory on a shroud test-piece that had been welded using the same procedure as employed in the field confirmed the success of the in situ repair operation. The alternate option available was replacing the cracked blade and the shroud piece to which it is riveted with a new one, reducing the height of all the blades attached to the shroud by machining, riveting the blades with reduced height to the new shroud, and, finally, dynamic balancing of the entire turbine after completion of the repair. This option is both time-consuming and expensive. Hence, the successful completion of this repair welding resulted in enormous savings both in terms of reducing the downtime of the plant and the cost of the repair. The turbine has been put back into service and has been operating satisfactorily since December 2000.