A CALCULATION METHOD OF OBTAINING DESORPTION ISOTHERMS OF BEECH (FAGUSMOESL4CA) WOOD

ABSTRACT

This paper presents the specific methods to obtain sorption isotherms. Sorption isotherms were first obtained experimentally for 20°C and 100°C and then, by using the presented method, isotherms were also obtained for 50°C and 80°C. The same treatment can be applied in finding any isotherm sorption in the temperature range between 20°Cand 100°C.

The experiments were carried out on beech (Fagus moesiaca) and sample dimensions were 3×3×3cm. Based on the results of the experiment, by regression analysis, the most suitable analytic formula was proposed. It relsites temperature and air humidity with the equilibrium moisture content in wood. Experimental results were compared with psychrometric tables and Bramhall's formula for desorption curves with good agreement. This proves that the method presented in this paper is precise and efficient to decrease the lime needed to obtain sorption isotherms experimentally.     

Fully-Naphthalenoid Hydrocarbons and their Conjugation Modes

Abstract

A fully-naphthalenoid hydrocarbon (FUN) is a benzenoid hydrocarbon whose all π-electrons can be (formally) grouped into disjoint naphthalene-units. The cyclic conjugation in FUNs is studied by means of the energy-effects of their various cycles. It is found that the dominant conjugation modes in FUNs are those involving the 6- and 10-membered cycles of the “full” naphthalene fragments. The cycles belonging to the “empty” domains of a FUN have significantly smaller energy-effects.     

Effect of preparation route on the microstructure and electrical conductivity of co-doped ceria

Dense Ce_0.8Sm_0.1Gd_0.1O_2?δ electrolytes were fabricated by sintering of CeO₂ solid solutions which were prepared from metal nitrates and NaOH using self propagating room temperature synthesis (SPRT). Three different routes were employed to obtain CeO₂ solid solution powders: (I) hand mixing of reactants, (II) ball milling of reactants and (III) ball milling of Ce_0.8Sm_0.2O_2?δ and Ce_0.8Gd_0.2O_2?δ solid solutions previously prepared by ball milling of corresponding nitrates and NaOH. Density measurements showed that ball milling, which is more convenient than hand mixing, is an effective way to obtain almost full dense samples after presureless sintering at 1550 °C for 1 h. These samples had larger grain size and consequently higher conductivity than the samples obtained by hand mixing. The highest conductivity of 2.704×10^?2 (Ω cm)^?1was measured at 700 °C in a sample prepared by route II. It was found that reduced grain size in samples obtained by hand mixing leads to a decrease in grain boundary conductivity and therefore decrease in the total conductivity. The results showed that mixing of single doped ceria solid solutions improved densification and inhibited grain growth.     

Thermodynamic modeling of vapor-liquid equilibria and excess properties of the binary systems containing diethers and n-alkanes by cubic equation of state

A comparison of the performances of two different approaches of cubic equations of state models, based on a classical van der Waals and mixing rules incorporating theG ^E equation, was carried out for correlation of Vapor-Liquid Equilibria (VLE), H^E and C _P ^E data alone, and simultaneous correlation of VLE+H^E, VLE+C _P ^E , H^E +C _P ^E and VLE+H^E +C _P ^E data for the diethers (1,4-dioxane or 1,3-dioxolane) with n-alkane systems. For all calculations the Peng-Robinson-Stryjek-Vera cubic equation of state (PRSV CEOS) was used. A family of mixing rules for the PRSV CEOS based on the Modified van der Waals one-fluid mixing rule (MvdW1) and two well-known CEOS/G^E mixing rules (MHV1 and MHV2), was considered. The NRTL equation, as the G^E model with linear or reciprocal temperature dependent parameters, was incorporated in the CEOS/G^E models. The results obtained by the CEOS/G^E models exhibit significant improvement in comparison to the MvdW1 models.     

Electrospun Poly(styrene) Fibers as a Protection for the First- and the Second-Generation Grubbs’ Catalyst

The study presents a novel method for protection of the first- and the second-generation Grubbs’ catalyst, by incorporation in poly(styrene) fibers through electrospinning technique. Both catalysts are sensitive to the presence of the amine hardeners in the epoxy-based self-healing composites and require protection from deactivation to retain their ability to promote polymerization reaction of the healing agent. Comparison of healing efficiencies of both catalysts suggested that poly(styrene) fibers offer better protection and dispersion for the first-generation Grubbs’ catalyst, although all the samples exhibited high-healing efficiency. Difference in stereoselectivity between two catalysts was also indicated.     

Hydrogen Effervescence from Aluminum Alloy Melts

With expansion of integrated computational materials engineering, new mathematical models are required for the assessment of processes that traditionally were manually monitored on factory production floors. The Richards logistic function is used to describe the total amount of porosity in an as-cast aluminum alloy sample after treatment under near vacuum and atmospheric pressures. The acquired function constants were correlated to the different process parameters during solidification. It is found that the Richards logistic function describes the best formation of porosity in aluminum alloy melts. The maximum porosity (M _P) and lowest porosity level (L _P) constants are directly related to the highest and lowest porosity levels in the analyzed samples, while the rate (r) defines the increase of porosity with respect to an increase in dissolved hydrogen between the threshold and mass transfer limits. The Richards logistic function can be used instead of traditional low-order mathematical equations to predict threshold limit and amount of porosity in solidified aluminum alloys by assessing the hydrogen concentration in aluminum alloy melts.     

Short Electrospun Fibers by UV Cutting Method

Short electrospun fibers were obtained by using UV cutting method. Either polymers with double bonds with a photocross‐linker (CL) and photoinitiator (PI) or known photochemistry of coumarin ([2 + 2] cycloaddition reaction) without the addition of CL and PI is utilized for making short electrospun fibers. The electrospun fibers were irradiated by UV light in the presence of a mask with a defined width of slits. The uncovered parts of fibers were cross‐linked and therefore became insoluble. The non‐cross‐linked parts were removed by immersion of the fibers into an appropriate solvent. The length of obtained short fibers can be controlled by changing the width of the slits of the employed mask.

     

Determination of 200 °C Isothermal Section of Al-Ag-Ga Phase Diagram by Microanalysis,X-ray Diffraction,Hardness and Electrical Conductivity Measurements

Ternary Al-Ag-Ga system at 200 °C was experimentally and thermodynamically assessed. Isothermal section was extrapolated using optimized thermodynamic parameters for constitutive binary systems. Microstructure and phase composition of the selected alloy samples were analyzed using light microscopy, scanning electron microscopy combined with energy-dispersive spectrometry and x-ray powder diffraction technique. The obtained experimental results were found to be in a close agreement with the predicted phase equilibria. Hardness and electrical conductivity of the alloy samples from four vertical sections Al-Ag₈₀Ga₂₀, Al-Ag₆₀Ga₄₀, Ag-Al₈₀Ga₂₀ and Ag-Al₆₀Ga₄₀ of the ternary Al-Ag-Ga system at 200 °C were experimentally determined using Brinell method and eddy current measurements. Additionally, hardness of the individual phases present in the microstructure of the studied alloy samples was determined using Vickers microhardness test. Based on experimentally obtained results, isolines of Brinell hardness and electrical conductivity were calculated for the alloys from isothermal section of the ternary Al-Ag-Ga system at 200 °C.     

Transmittance Measurements in Non-alternating Magnetic Field as Reliable Method for Determining of Heating Properties of Phosphate and Phosphonate Coated Fe3O4 Magnetic Nanoparticles

Different phosphates and phosphonates have shown excellent coating ability toward magnetic nanoparticles, improving their stability and biocompatibility which enables their biomedical application. The magnetic hyperthermia efficiency of phosphates (IDP and IHP) and phosphonates (MDP and HEDP) coated Fe₃O₄ magnetic nanoparticles (MNPs) were evaluated in an alternating magnetic field. For a deeper understanding of hyperthermia, the behavior of investigated MNPs in the non-alternating magnetic field was monitored by measuring the transparency of the sample. To investigate their theranostic potential coated Fe₃O₄-MNPs were radiolabeled with radionuclide ¹⁷⁷Lu. Phosphate coated MNPs were radiolabeled in high radiolabeling yield (>?99%) while phosphonate coated MNPs reached maximum radiolabeling yield of 78%. Regardless lower radiolabeling yield both radiolabeled phosphonate MNPs may be further purified reaching radiochemical purity of more than 95%. In vitro stabile radiolabeled nanoparticles in saline and HSA were obtained. The high heating ability of phosphates and phosphonates coated MNPs as sine qua non for efficient in vivo hyperthermia treatment and satisfactory radiolabeling yield justifies their further research in order to develop new theranostic agents.

     

Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.