Electrical and stability properties and ultrasonic microscope characterisation of low temperature co-fired ceramics resistors

This paper presents systematic investigations of electrical and stability properties of various low temperature co-fired ceramics (LTCC) resistors. One of the goals of this work was to check the compatibility of LTCC materials (tapes, resistive and conductive inks) from various manufacturers. Three commercially available green tapes and three LTCC resistor/conductor systems were examined. The resistive inks with 1 kΩ/sq. nominal sheet resistance were used. Buried (inside) and surface resistors were laminated and fired according to the tape manufacturers’ recommendations. The influence of dimensional effect on sheet resistance and hot temperature coefficient of resistance, the temperature dependence of resistance in a wide temperature range (from −180°C to +130°C), long-term stability of thermally aged as-fired resistors (150°C, 500 h) and durability to high-voltage micro- or nanosecond pulses (50 ns pulses with 4000 V/mm maximum electric field or 10 μs ones with 700–1000 V/mm electrical field) were carried out for electrical and stability characterisation of LTCC resistors. Non-destructive scanning acoustic microscope diagnostics was applied for structure investigation and estimation of lamination and cofiring process quality of buried LTCC resistors.     

Doping efficiency and energy-level scheme in C60F48-doped zinc–tetraphenylporphyrin films

High resolution synchrotron-based core level spectroscopy was used to examine the energy level alignment at the interface of zinc–tetraphenylporphyrin films doped by the surface acceptor C₆₀F₄₈. Two distinct fluorofullerene charge states were identified, corresponding to ionized and neutral molecules, and their relative concentration as a function of coverage was used to evaluate the probability of occupation of the acceptor lowest unoccupied molecular orbital (LUMO). From an initial acceptor energy of ?0.25 eV, the C₆₀F₄₈ LUMO shifts upwards with coverage due to a doping-induced interfacial dipole potential, and stabilization of the LUMO at an energy 0.45 eV above the Fermi energy was obtained. While the energy difference upon saturation is consistent with the results obtained for other donor–acceptor systems that have been interpreted as Fermi level pinning, the present work shows that the energy offset is a direct consequence of the interplay between Fermi–Dirac statistics in combination with the interfacial dipole potential.     

Glycosidic linkages of legume,grass and cereal straw cell walls before and after extensive degradation by rumen microorganisms

The technique of methylation analysis for the location of glycosidic linkages in cell wall polysaccharides was applied directly (after dry milling in liquid nitrogen) to whole wheat and barley straws, cell wall preparations from early- and late-cut perennial ryegrass and white clover, and their extensively degraded residues recovered from the rumen. The addition of an internal standard, methyl-β-D-allo-pyranose, to milled samples enabled the recovery of partially-methylated sugars to be quantified, and the recovery of parent sugars from methylated material to be compared with values obtained by direct estimation of monosaccharides by the alditol acetate method. Recovery of sugars from methylated samples was generally higher than that predicted by the alditol acetate method, particularly from digested residues. All four samples of Gramineae showed similar proportions of glycosidic linkages in which (1 →4)-linked xylose and glucose units accounted for more than 80% of total identified partially-methylated sugars. The proportions of glycosidic linkages found in digested residues of straws were essentially the same as those found in the parent material. In residues of the more digestible ryegrass there was a two- to three-fold increase in (1→4)-linked xylose units without branch points at the O-2/O-3 positions, the proportions of these branch points being substantially reduced. A corresponding reduction in the proportion of (1→2)-, (1→3)-and terminally-linked arabinose units was also found. The proportion of both (1→4)- and (1→3)-linked glucose units were also reduced in digested residues. These changes were greater in the early-cut than in the late-cut sample. White clover differed from the Gramineae in a number of respects. Galactose units predominantly in the form of (1→4)-, (1→6)- and terminally-linked units, were the major non-cellulosic sugars present. The proportion of all forms of galactose was reduced in digested residues, but (1→6)-linked units appeared more resistant to degradation than (1→4)-linked units. Like ryegrass, the proportion of xylose units increased in digested residues from clover, while the proportion of glucose decreased. The proportion of (1→4)-linked mannose units, initially present at levels ten times as great as in the Gramineae, was also substantially reduced.     

Direction finding using data-supported optimization

A novel data-supported optimization technique for maximum likelihood (ML) direction-of-arrival estimation is proposed. The essence of our approach is to optimize the likelihood function at certaindata-supported points obtained by a resampled root-MUSIC procedure. These points are shown to comprise a small but representative subset of all possible searching points and contain enough information for solving the ML problem.This work was supported in part by grants from the National Sciences and Engineering Research Council of Canada (NSERC), Ministry of Energy, Science and Technology (MEST) of Ontario, Communications and Information Technology Ontario (CITO), and by the Senior Individual Grant Program of the Swedish Foundation for Strategic Research.     

Design aspects of MOS-controlled thyristor elements: technology,simulation, and experimental results

2.5-kV thyristor devices have been fabricated with integrated MOS controlled n⁺-emitter shorts and a bipolar turn-on gate using a p-channel DMOS technology. Square-cell geometries with pitch variations ranging from 15 to 30 μm were implemented in one- and two-dimensional arrays with up to 20000 units. The impact of the cell pitch on the turn-off performance and the on-state voltage was studied for arrays with constant cathode area as well as for single-cell structures. By realizing MOS components with submicrometer channel lengths, scaled single cells are shown to turn off with current densities of several kiloamperes per square centimeter at a gate bias of 5 V. In the case of multi-cell ensembles, turn-off performance is limited due to inhomogeneous current distribution. Critical process parameters as well as the device behavior were optimized through multidimensional numerical simulation     

trans-dominant mutations in the GPR1 gene cause high sensitivity to acetic acid and ethanol in the yeast Yarrowia lipolytica

Acetate non-utilizing strains harbouring trans-dominant mutations in the GPR1 gene (GPR1(d)) of the dimorphic yeast Yarrowia lipolytica have been selected and characterized. These mutants are highly sensitive to low concentrations of acetic acid and ethanol, even in presence of glucose. The toxic effect of acetic acid is pH-dependent and has the strongest effect at low pH. In contrast, the action of ethanol is pH-independent. One GPR1(d) mutant has been detected that was highly sensitive to acetic acid but could still grow on ethanol, which indicates putative differences in the function of the GPR1 gene product in the sensitivity to acetic acid and ethanol. The GPR1(d) mutants exhibit a complex pleiotropic phenotype. The mutations cause changed colony morphology as well as dimorphism of cells, and induce early cell death during growth on glucose, even without the presence of dicarbon compounds. Composition of intracellular membranes, as well as morphology of vacuole and mitochondria, were strongly changed. Back-crosses with wild-type strains and analysis of recombinant strains have shown that the expression of the pleiotropic phenotype depends on the site of mutation in the GPR1 gene, as well as on the genetic background of the strain harbouring the responsive mutation. Our data suggest that Gpr1p is involved in a general response of cells to the toxic action of dicarbon compounds like acetic acid and ethanol.     

Halogen-free solvent processing for sustainable development of high efficiency organic solar cells

Eliminating processing with halogenated solvents is desirable to achieve sustainable large-scale fabrication of organic solar cells. This work demonstrates a device processing approach completely free of halogenated solvents to yield high-performance (power conversion efficiency, η_P > 6%) polymer:fullerene bulk-heterojunction solar cells comprising a conjugated polymer PIDT-phanQ and [6,6]-phenyl-C71-butyric acid methyl ester (PC₇₁BM). Introducing 2% 1-methylnaphthalene (Me-naph) as a processing additive to toluene alleviates PC₇₁BM solubility problems, reduces phase domain size by two orders of magnitude, and boosts efficiency from η_P = 0.02% to 6.10%. Both AFM and TEM imaging show that the Me-naph additive promotes a more finely phase-separated morphology in spin-coated films, while photoluminescence quenching and photoinduced absorption spectroscopy confirm that this finer morphology results in both better exciton quenching and more efficient charge separation.     

Bottom-contact small-molecule n-type organic field effect transistors achieved via simultaneous modification of electrode and dielectric surfaces

Low-voltage, n-type organic field effect transistors (OFETs) with simultaneously modified bottom-contact (BC) electrodes and dielectric were compared to their top-contact (TC) counterparts. The devices modified with 6-phenoxyhexylphosphonic acid (Ph6PA) self-assembled monolayer (SAM) showed similar performance, morphology, and contact resistance. Electron mobility of C₆₀ devices were 0.212 and 0.320 cm² V⁻¹ s⁻¹ and [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) devices were 0.04 and 0.06 cm² V⁻¹ s⁻¹ for TC and BC devices, respectively. Low contact resistance between 11 and 45 kΩ cm was found regardless of device architecture or n-type semiconductor used. This work shows it is possible to fabricate solution processable low-voltage bottom-contact devices with performance that is similar or better than their top-contact counterparts without the addition of complex and time-consuming processing steps.